Re: Z series stuff again

[mark krawczuk]

hi, when i got my  latest set of pistons, and even the set before that, they didnt even ask about wether it was a  z20e or a z20s also that means the conrods must be a different length as well....        mark k this is getting confusing,  i cant see why they would change the piston,  what a hassel that would be to cast  other pistons  for the same motor,  imagine if holden  or whatever made  2 different  sets of pistons for 106 etc....   would it actually be worth the cost , for  no gain in performance haviong two sets of pistons?     ----- Original Message ----- From: Richardson, Thomas Morgwn - RICTM002 To: '[EMAIL PROTECTED]' Sent: Monday, December 03, 2001 9:28 PM Subject: RE: Z series stuff again Yup   Z20E 31.6mm vs Z20S 35.5mm -----Original Message----- From: mark krawczuk [mailto:[EMAIL PROTECTED]] Sent: Monday, 3 December 2001 9:03 PM To: [EMAIL PROTECTED] Subject: Re: Z series stuff again hi, whats the difference between the z20e and z20s pistons?i presume its the gudgeon  pin position?   mark k     ----- Original Message ----- From: Richardson, Thomas Morgwn - RICTM002 To: '[EMAIL PROTECTED]' Sent: Monday, December 03, 2001 5:49 PM Subject: RE: Z series stuff again Actually Mark, there are two different types of Z20 pistons, Z20E and Z20S.  Eddie will be able to use the L20b pistons if he uses L20b conrods.  He wouldn't be able to use the longer Z20S rods and L20b pistons unless he REDUCED the Z20 crankshaft stroke. -----Original Message----- From: mark krawczuk [mailto:[EMAIL PROTECTED]] Sent: Monday, 3 December 2001 11:40 AM To: [EMAIL PROTECTED] Subject: Re: Z series stuff again hi,  they will work , but it depends on  what crank, rod  etc, combonation  u are using. in my l20  with z24 crank, i am using  1 mm oversize Z20 pistons. the gudgeon pin to crown height is closer than a  l20b piston. i am using the z20 pistons  due to the extra stroke of the crank. if u use the z20 and put in the l20 pistons , they will stick out the block. like i said depends on what conrod , crank combo u end up using.  mark k .----- Original Message ----- From: [EMAIL PROTECTED] To: [EMAIL PROTECTED] Sent: Monday, December 03, 2001 9:51 AM Subject: Re: Z series stuff again Will pistons intended for an L20B work in a Z20S? I'm converting a Z20S into an L series and have been offered some high comp cosworth pistons but they are for an L20B. I was under the impression that Z20S motors have longer rods...is that true?   Cheers, Eddie Rattley England [EMAIL PROTECTED] www.ratdat.com --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ --------------------------------------------------------------------- --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/membersozdat@datascribe.com.au/ ---------------------------------------------------------------------