In the world of heavy trucks they get around the stud loosening issues by using 
longer studs. They add about a 2" long spacer under the nut. This effectively 
lowers the spring rate of the stud so it can vary in length more with thermal 
expansion and still keep clamp load. A good portion of the stud is further away 
from the heat source as well so it doesn't expand as much as the parts being 
held together.

I have countersunk my manifold to turbo to manifold stud holes so I get about 
12mm more grip length I think it helped but it hasn't cured the problem. 

Bob
  ----- Original Message ----- 
  From: Mark Rieb 
  To: [email protected] 
  Cc: [email protected] ; [email protected] 
  Sent: Thursday, April 02, 2009 6:43 AM
  Subject: Re: Re: loosening turbo to mani and turbo to d/p nuts


  Inconel would expand even more and cause more of a problem.  The coefficient 
of thermal expansion for all of the stainless steels (304, 316, 320, inconel, 
hastalloy, etc.) is nearly double that for the carbon steels.

  The Mitsubishi world has the same issues, with the added problem of shearing 
off the endmost studs from the differences in thermal expansion between the 
aluminum head and cast iron exhaust manifold - the newer cars use a larger stud 
in the endmost holes.  At one point I was using a belleville ("wavey") washer 
and wide based locking nuts from BMW to keep things together on an engine that 
was taxing the max flow of a 16g turbo.  The Belleville washer keeps tension on 
the joint when the stud expands.

  Mark


  Apr 2, 2009 06:33:29 AM, [email protected] wrote:

    I have fought this issue for many years. I have installed bigger studs and
    used all manners of locking devices and compounds and nothing has solved
    the problem. I can drive on the street for miles and miles with no problems
    but a track day brings it right back. I am convinced that the problem is
    not with the studs or nuts backing out(because I am sure I prevented that)
    but with the studs stretching under the high heat loads seen on track. I
    even spoke to ARP about getting some custom studs made from inconel. I
    think that would solve the problem but the cost was nuts. My final solution
    to this issue was to build a V8 RX7 for track use.

    Steve

    Things I have tried:

    3/8 studs
    Safety wire
    High temp thread locker - (2000 degrees aircraft shit $$$$)
    Nordlocks
    Best studs I could find - (ARP header studs)



    Emilio - 
    949Racing 
    com> MiataPower 
    Sent by: <[email protected]> 
    miatapower-bounce cc 
    [email protected] 
    Subject 
    Re: loosening turbo to mani and 
    04/01/2009 11:39 turbo to d/p nuts 
    PM 









    My experience has been that its more the studs backing out. So even, stage
    8's, Nordlocks, safety wire and what not doesn't always fix it. Someone at
    MRLS mentioned that FM may be switching to or optionally offering 10mm
    studs with their kits. The extra surface area does seem to make them stay
    put longer. 10m studs have been de rigueur for turbo Miatas that see a lot
    of track use but its trickling down to street cars slower it seems. I
    haven't tried green, hi temp cylindrical bonding Loctite but that might
    help. Another fix might be staking them, but that may raise cracking issues
    with cast manifolds.

    Jason, you don't track your car do you? That's when stuff falls off :) I've
    seen daily driven turbo cars that have never had an an issue on the street,
    not make one session at the track before a stud or two backs out.

    But to answer your question yes, it's endemic for turbo track miatas.

    Emilio Cervantes
    www.949Racing.com
    26242 Dimension Dr #130
    Lake Forest, CA 92630
    949.716.3111 phone / fax

    On 2009-04-02 03:05, Jason C wrote:
    > A lot of people seem to have this problem (though not me)....I want
    to understand why some do and some don't. Â Some do despite the
    fancy serrated FM washers.Do FM see this problem?



    ______________________________________________________________________
    This email has been scanned by the MessageLabs Email Security System.
    For more information please visit http://www.messagelabs.com/email
    ______________________________________________________________________
    _______________________________________________
    Miatapower mailing list
    [email protected]
    http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower


    _______________________________________________
    Miatapower mailing list
    [email protected]
    http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower



------------------------------------------------------------------------------


  _______________________________________________
  Miatapower mailing list
  [email protected]
  http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower
_______________________________________________
Miatapower mailing list
[email protected]
http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower

Reply via email to