Small general purpose engine EFI components have been developed for the far
eastern motor scooter markets so appropriate pumps, injectors, ecu, sensor,
etc are all developed. Delphi among others have the stuff. Kohler just
announced the release of efi small engines but the cost is high compared to
carbs. Only high end applications will pay for it.

The new emissions regs are going to drive aftertreatment not efi because
the emission improvement of efi is very small the way it is measure in the
audit process.


                                                                           
             Ashraf Farrag                                                 
             <ashraf_far...@ms                                             
             ccnc.org>                                                  To 
             Sent by:                  [email protected]                      
             miatapower-bounce                                          cc 
             [email protected]          [email protected]           
                                                                   Subject 
                                       Re: [npc] alternative fuel lawn     
             04/20/2009 11:26          equipment                           
             AM                                                            
                                                                           
                                                                           
             Please respond to                                             
             ashraf_far...@msc                                             
                  cnc.org                                                  
                                                                           
                                                                           




Ian McCloghrie wrote:
> Maybe it's fuel-injected and it needs the battery to get the ECU
> running? :)
This is way, way off topic at this point but here are my musings on that
subject...  ;-)

When I was fighting the carburetor, I was "this close" (well, not
really, since it is not practical) in frustration (and to some extent
still am, since it doesn't run well under power) to just making a big
experiment out of it and converting to a jury rigged DIY fuel injection,
probably the microsquirt variant of the Megasquirt project.

I've seen that the bits and pieces to do just that are starting to be
developed but I don't think they have hit the market quite yet.  They
(Bosch) apparently have started to develop small engine fuel pumps (more
a problem, IMHO than the computer).  Could probably even use a
carburetor pump at low pressure...I think I read that some small engine
actually have a pump.

Injectors for that size of displacement probably aren't common, though,
so I'm not sure what off-the-shelf component you could borrow/use.
Given the fuel atomization isn't a huge issue, I wonder if some sort of
industrial standard solenoid valve could be used in front of a carb jet
to meter the fuel for the engine size (same ones that folks use for
boost control solenoids).

The ECU, for constant load, wouldn't take much computer to inject the
fuel if you keep the magneto for ignition, in fact, the rotary airplane
guys came up with an "ECU" that used a 555 timer chip.  Genius of a
hack.  Pure genius, I tell you.

I wonder if there's enough output from a larger magneto that could
charge a capacitor to run the ECU/pump/injector to bypass the battery.
Pull #1 charges the capacitor.  Pull #2 starts the mower.

For a unit cost of $350, I don't think they can replace the carburetor
with fuel injection and keep the costs reasonable on a push-mower
(yet).  I think it makes sense for inject a riding mower/tractor for the
immediate future.

I also saw somewhere that there will be new emissions requirements for
small engines?  That may be the real push to engineer fuel injection for
that market segment.

Alternately, I could just yank the carb (again), dip it in the parts
dip, reset the float and it will probably work right.

Take note, Bryan:
I just need to remember to drain the gas at the end of each season or
put Stabil in there so it doesn't varnish the carburetor innards.  :)

Regards,
--Ashraf
_______________________________________________
Miatapower mailing list
[email protected]
http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower

______________________________________________________________________
This email has been scanned by the MessageLabs Email Security System.
For more information please visit http://www.messagelabs.com/email
______________________________________________________________________


_______________________________________________
Miatapower mailing list
[email protected]
http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower

Reply via email to