Hi! I've added new R52H intereface to my RB411U (Level4) with 5.16 firmware.
I can see IRQ: ---------------------------------------------------------------------------------------------------------------- /system resource pci> print # DEVICE VENDOR NAME IRQ 0 00:12.0 Atheros Communications Inc. AR5413 802.11abg NIC (r... 48 ---------------------------------------------------------------------------------------------------------------- but not interface ---------------------------------------------------------------------------------------------------------------- /interface> print Flags: D - dynamic, X - disabled, R - running, S - slave # NAME TYPE MTU L2MTU MAX-L2MTU 0 R ether1 ether 1500 1526 1526 ---------------------------------------------------------------------------------------------------------------- other test: - Downgrate to 5.12 not resolve the problem - Upgrade to 6.0beta2 not resolve the problem - Adding/Removing 3G modem not change R52H interface status - Reset configuration (to default) not solve the problem During boot, if R52H is connected, I can see this by serial port: ---------------------------------------------------------------------------------------------------------------- jumping to kernel code Starting... Starting services... Oops[#1]: Cpu 0 $ 0 : 00000000 00000064 d1320000 deadc0de $ 4 : 000000c8 00004d58 ffffffff c03bebac $ 8 : c03c2c65 00000000 000000bc 00000000 $12 : 00000000 080072ff 080072df 6e637920 $16 : c1f70000 00000002 fffcffff 00000064 $20 : 00010000 c1f74470 0000005a c1f70080 $24 : 00000003 00000000 $28 : c1f6c000 c1f6dc58 00450000 c1faabf0 Hi : 000000bc Lo : a1d80000 epc : c1faabfc a5212_swba_int+0x382c/0x4a08 [a5212@0xc1fa0000] Tainted: P ra : c1faabf0 a5212_swba_int+0x3820/0x4a08 [a5212@0xc1fa0000] Status: 1000c603 KERNEL EXL IE Cause : 1080001c PrId : 00019374 (MIPS 24Kc) Process insmod (pid: 236, threadinfo=c1f6c000, task=c085c450, tls=00000000) Stack : 00010000 000000d0 00438a4c 00010000 c1f70000 00000013 00000013 00000000 00000000 c1fab5a0 000000d0 00000041 d0000000 00000000 00000001 00000034 10000000 00000000 00000000 00000000 c1f70000 00000000 00000000 c1fac4dc 10000000 c1f74470 0000005a c1f70080 00000000 c02f9a54 10000000 c010ffdc c1f70000 c1f70080 00000002 d1320000 10000000 c1fa20a0 00000000 0000000a ... Call Trace: [<c1faabfc>] a5212_swba_int+0x382c/0x4a08 [a5212@0xc1fa0000] [<c1faabf0>] a5212_swba_int+0x3820/0x4a08 [a5212@0xc1fa0000] Code: 8e020a18 26310001 8c434004 <00721824> ac434004 5633fff4 8e020a18 3c0 ---[ end trace dfde3d450a918355 ]--- Netfilter messages via NETLINK v0.30. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub MikroTik 5.16 MikroTik Login: ctnetlink v0.93: registering with nfnetlink. ip6_tables: (C) 2000-2006 Netfilter Core Team usbcore: registered new device driver usb ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver rb400-ohci rb400-ohci.0: RB400 OHCI rb400-ohci rb400-ohci.0: new USB bus registered, assigned bus number 1 rb400-ohci rb400-ohci.0: irq 22, io mem 0x1c000000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ip_tables: (C) 2000-2006 Netfilter Core Team usb 1-2: new full speed USB device using rb400-ohci and address 2 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not aftr ath chip revision: 000000a8 rb400-ehci rb400-ehci.0: RB400 EHCI rb400-ehci rb400-ehci.0: new USB bus registered, assigned bus number 2 rb400-ehci rb400-ehci.0: irq 3, io mem 0x1b000000 rb400-ehci rb400-ehci.0: USB 2.0 started, EHCI 1.00 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ar724x_usb: Host Tx Pre-Buffer Packet Tuning [00000000] usb 1-2: can't set config #1, error -62 usb 1-2: USB disconnect, address 2 netfilter PSD loaded - (c) astaro AG hub 2-0:1.0: unable to enumerate USB device on port 2 usbcore: registered new interface driver usbserial USB Serial support registered for generic usb 1-2: new full speed USB device using rb400-ohci and address 3 usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for Sierra USB modem sierra 1-2:1.0: Sierra USB modem converter detected usb 1-2: Sierra USB modem converter now attached to ttyUSB0 usb 1-2: Sierra USB modem converter now attached to ttyUSB1 usb 1-2: Sierra USB modem converter now attached to ttyUSB2 usbcore: registered new interface driver sierra sierra: v.1.7.16:USB Driver for Sierra Wireless USB modems rb400_beep 5000 rb400_beep 0 rb400_beep 5000 rb400_beep 0 rb400_beep 0 reset ag7100 eth0: reset unit 0 (phy 1) eth0: open skb_bin_request: add eth0 1526 1622 eth0: reset unit 0 (phy 1) eth0: link down ---------------------------------------------------------------------------------------------------------------- and without any operation this is the "console" abnormar output: ---------------------------------------------------------------------------------------------------------------- alg: No test for ecb(cipher_null) (ecb-cipher_null) alg: No test for digest_null (digest_null-generic) alg: No test for compress_null (compress_null-generic) NET: Registered protocol family 15 mpls_nl_init: id 17 fan: init rb_ioctl, cmd: 0x1, arg: 0x0 rb: RB_CFG_SIZE rb_ioctl, cmd: 0x3, arg: 0x4208d0 rb: RB_READ_CFG rb_ioctl, cmd: 0xf, arg: 0x0 rb: RB_GET_TYPE rb_ioctl, cmd: 0x2, arg: 0x0 rb: RB_INFO_SIZE rb_ioctl, cmd: 0x4, arg: 0x4218d8 rb: RB_READ_INFO ---------------------------------------------------------------------------------------------------------------- The RB is real instable (crash and very very slow) with R52H into slot. Thanks for your support. Best regards --- Sim _______________________________________________ Mikrotik mailing list Mikrotik@mail.butchevans.com http://www.butchevans.com/mailman/listinfo/mikrotik Visit http://blog.butchevans.com/ for tutorials related to Mikrotik RouterOS
