Hello,
I've been working on setting up a Sun Ultra5 running OpenBSD 3.6 Current (Sparc64). My plan is to use it as a router/wireless access point for my home network. The card I'm using is a D-Link DWL-520 rev. B (Prism 2.5 chipset). I checked the hardware compatibility list and it is listed.
I get this with dmesg:
# dmesg |grep wi0
wi0 at pci2 dev 3 function 0 "Intersil PRISM2.5" rev 0x01: ivec 18wi0: init failed
ifconfig doesn't work either:
# ifconfig wi0 up ifconfig: SIOCGIFFLAGS: Device not configured
I asked someone over at freebsdforums.org and they said it sounded like the card hadn't been given "seen" by the hardware. I know next to nothing about Sun hardware but a brief tour through the manuals didn't mention any special steps about setting up PCI cards. My PCI ethernet card seems to be working fine as well.
I also understand their might be some issue as to if the card is supported or not since it seems these days manufactures like to change chipsets without changing model numbers. However it does seem to be a Prism 2.5-based card and it is listed as a compatible card... but then again... wireless...
Anyway, I'm not to sure where to go from here but any help or ideas would be very welcome. Thanks in advance.
I've also included my full dmesg output just in case someone might find it useful:
-----
console is keyboard/display
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2004 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 3.6-stable (GENERIC) #0: Sun May 1 12:07:28 AKDT 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/sparc64/compile/GENERIC
total memory = 536870912
avail memory = 480428032
using 3276 buffers containing 26836992 bytes of memory
bootpath: /[EMAIL PROTECTED],0/[EMAIL PROTECTED],1/[EMAIL PROTECTED],0/[EMAIL PROTECTED],0
mainbus0 (root): Sun Ultra 5/10 UPA/PCI (UltraSPARC-IIi 400MHz)
cpu0 at mainbus0: SUNW,UltraSPARC-IIi @ 400 MHz, version 0 FPU
cpu0: physical 32K instruction (32 b/l), 16K data (32 b/l), 2048K external (64 b/l)
psycho0 at mainbus0 addr 0xfffc4000
SUNW,sabre: impl 0, version 0: ign 7c0 bus range 0 to 2; PCI bus 0
DVMA map: c0000000 to e0000000
IOTDB: 29e8000 to 2a68000
pci0 at psycho0
ppb0 at pci0 dev 1 function 1 "Sun Simba PCI-PCI" rev 0x13
pci1 at ppb0 bus 1
ebus0 at pci1 dev 1 function 0 "Sun PCIO Ebus2" rev 0x01
auxio0 at ebus0 addr 726000-726003, 728000-728003, 72a000-72a003, 72c000-72c003, 72f000-72f003
power at ebus0 addr 724000-724003 ipl 37 not configured
SUNW,pll at ebus0 addr 504000-504002 not configured
sab0 at ebus0 addr 400000-40007f ipl 43: rev 3.2
sabtty0 at sab0 port 0
sabtty1 at sab0 port 1
comkbd0 at ebus0 addr 3083f8-3083ff ipl 41: layout 34
wskbd0 at comkbd0: console keyboard
com0 at ebus0 addr 3062f8-3062ff ipl 42, mouse: ns16550a, 16 byte fifo
lpt0 at ebus0 addr 3043bc-3043cb, 30015c-30015d, 700000-70000f ipl 34: polled
fdthree at ebus0 addr 3023f0-3023f7, 706000-70600f, 720000-720003 ipl 39 not configured
clock0 at ebus0 addr 0-1fff: mk48t59: hostid 80d15042
flashprom at ebus0 addr 0-fffff not configured
audioce0 at ebus0 addr 200000-2000ff, 702000-70200f, 704000-70400f, 722000-722003 ipl 35 ipl 36: nvaddrs 0
audio0 at audioce0
hme0 at pci1 dev 1 function 1 "Sun HME" rev 0x01: address 08:00:20:d1:50:42
nsphy0 at hme0 phy 1: DP83840 10/100 media interface, rev. 1
hme0: using ivec 3021 for interrupt
vgafb0 at pci1 dev 2 function 0 "ATI Mach64 GP" rev 0x5c
wsdisplay0 at vgafb0: console (std, sun emulation), using wskbd0
pciide0 at pci1 dev 3 function 0 "CMD Technology PCI0646" rev 0x03: DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide0: using ivec 1820 for native-PCI interrupt
wd0 at pciide0 channel 0 drive 0: <WDC WD102BA>
wd0: 16-sector PIO, LBA, 9779MB, 20028960 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <LG, CD-ROM CRD-8322B, 1.05> SCSI0 5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2
ppb1 at pci0 dev 1 function 0 "Sun Simba PCI-PCI" rev 0x13
pci2 at ppb1 bus 2
xl0 at pci2 dev 1 function 0 "3Com 3c905 100Base-TX" rev 0x00: ivec 10, address 00:60:08:1c:53:7e
nsphy1 at xl0 phy 24: DP83840 10/100 media interface, rev. 1
wi0 at pci2 dev 3 function 0 "Intersil PRISM2.5" rev 0x01: ivec 18wi0: init failed
: unable to read station address
pcons at mainbus0 not configured
No counter-timer -- using %tick at 400MHz as system clock.
root on wd0a
rootdev=0xc00 rrootdev=0x1a00 rawdev=0x1a02
WARNING: clock gained 2 days -- CHECK AND RESET THE DATE!
