This sounds similar to a problem I was having, kind of. One of the odd things about the problem I was having though was that when I booted and redirected the console to the serial port so I could capture the trace etc. it wouldn't do it.
That doesn't help, but it is what I have to say. JR -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Marco Peereboom Sent: Wednesday, May 25, 2005 4:43 PM To: Steve Shockley Cc: Miscellaneous OBSD Subject: Re: Hang using generic.mp with ami0 hmmm very odd. Let me try to reproduce. On May 25, 2005, at 6:59 PM, Steve Shockley wrote: > I've just set up a Compaq Proliant 6500 with OpenBSD 3.7-release. > It works fine with the uniprocessor kernel, but when I boot from > bsd.mp, it sits at "mtrr: Pentium Pro MTRR support", then after a > minute or two it reports "ami0: timeout ccb 1" and hangs. > > I found http://marc.theaimsgroup.com/?m=109355301607068, which > suggested upgrading the firmware on the card. I upgraded to the > most current firmeware from AMI, no change. It's an HP NetRAID 2M > and/or Megaraid Elite 1600. > > Dmesg from /bsd: > > OpenBSD 3.7 (GENERIC) #50: Sun Mar 20 00:01:57 MST 2005 > [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC > cpu0: Intel Pentium III Xeon ("GenuineIntel" 686-class, 2048KB L2 > cache) 500 MHz > cpu0: > FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE3 > 6,MMX,FXSR,SSE > real mem = 3220791296 (3145304K) > avail mem = 2931523584 (2862816K) > using 4278 buffers containing 161140736 bytes (157364K) of memory > mainbus0 (root) > bios0 at mainbus0: AT/286+(00) BIOS, date 12/31/99, BIOS32 rev. 0 @ > 0xf0000 > pcibios0 at bios0: rev 2.1 @ 0xf0000/0x2000 > pcibios0: PCI BIOS has 10 Interrupt Routing table entries > pcibios0: PCI Interrupt Router at 000:15:0 ("Intel 82371AB PIIX4 > ISA" rev 0x00) > pcibios0: PCI bus #0 is the last bus > bios0: ROM list: 0xc0000/0x8000 0xc8000/0x1400 0xe8000/0x6000 > 0xee000/0x2000! > cpu0 at mainbus0 > pci0 at mainbus0 bus 0: configuration mode 1 (no bios) > fxp0 at pci0 dev 1 function 0 "Intel 82557" rev 0x0d, i82550: irq > 11, address 00:02:b3:8f:1a:3f > inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4 > "Compaq PCI Hotplug" rev 0x04 at pci0 dev 11 function 0 not configured > "Compaq Netelligent ASMC" rev 0x00 at pci0 dev 12 function 0 not > configured > siop0 at pci0 dev 13 function 0 "Symbios Logic 53c875" rev 0x14: > irq 10, using 4K of on-board RAM > scsibus0 at siop0: 16 targets > siop1 at pci0 dev 13 function 1 "Symbios Logic 53c875" rev 0x14: > irq 5, using 4K of on-board RAM > scsibus1 at siop1: 16 targets > vga1 at pci0 dev 14 function 0 "ATI Mach64 GV" rev 0x7a > wsdisplay0 at vga1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > pcib0 at pci0 dev 15 function 0 "Intel 82371AB PIIX4 ISA" rev 0x02 > pciide0 at pci0 dev 15 function 1 "Intel 82371AB IDE" rev 0x01: > DMA, channel 0 wired to compatibility, channel 1 wired to > compatibility > atapiscsi0 at pciide0 channel 0 drive 0 > scsibus2 at atapiscsi0: 2 targets > cd0 at scsibus2 targ 0 lun 0: <COMPAQ, CDR-8435, 0013> SCSI0 5/ > cdrom removable > cd0(pciide0:0:0): using PIO mode 4, DMA mode 2 > pciide0: channel 1 ignored (disabled) > uhci0 at pci0 dev 15 function 2 "Intel 82371AB USB" rev > 0x01pci_intr_map: no mapping for pin D > : couldn't map interrupt > "Intel 82371AB Power Mgmt" rev 0x02 at pci0 dev 15 function 3 not > configured > pchb0 at pci0 dev 16 function 0 "Intel 82451NX Mem & IO" rev 0x03 > pchb1 at pci0 dev 18 function 0 "Intel 82454NX PXB" rev 0x04 > pchb2 at pci0 dev 20 function 0 "Intel 82454NX PXB" rev 0x04 > pci1 at pchb2 bus 4 > ppb0 at pci1 dev 3 function 0 "DEC 21154 PCI-PCI" rev 0x05 > pci2 at ppb0 bus 5 > ppb1 at pci2 dev 0 function 0 "DEC 21154 PCI-PCI" rev 0x05 > pci3 at ppb1 bus 6 > ami0 at pci3 dev 0 function 0 "AMI MegaRAID" rev 0x02: irq 5 AMI > 493/64b/lhc > ami0: FW 111U, BIOS vF320, 128MB RAM > ami0: 2 channels, 0 FC loops, 1 logical drives > scsibus3 at ami0: 40 targets > sd0 at scsibus3 targ 0 lun 0: <AMI, Host drive #00, > SCSI2 0/ > direct fixed > sd0: 8677MB, 1106 cyl, 255 head, 63 sec, 512 bytes/sec, 17770496 > sec total > "QLogic ISP12160" rev 0x06 at pci2 dev 1 function 0 not configured > "Compaq PCI Hotplug" rev 0x04 at pci1 dev 11 function 0 not configured > > isa0 at pcib0 > isadma0 at isa0 > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0 (mux 1 ignored for console): console keyboard, > using wsdisplay0 > pms0 at pckbc0 (aux slot) > pckbc0: using irq 12 for aux slot > wsmouse0 at pms0 mux 0 > pcppi0 at isa0 port 0x61 > midi0 at pcppi0: <PC speaker> > sysbeep0 at pcppi0 > lpt0 at isa0 port 0x378/4 irq 7 > npx0 at isa0 port 0xf0/16: using exception 16 > pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 > fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec > biomask e765 netmask ef65 ttymask ffe7 > pctr: 686-class user-level performance counters enabled > mtrr: Pentium Pro MTRR support > dkcsum: sd0 matched BIOS disk 80 > root on sd0a > rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
