Did this work with a previous release or is this a new setup? // Brad
On Thu, May 26, 2005 at 05:12:09PM +0100, Stephen Marley wrote: > I have some boxes with dc (quad Znyx), xl and some virtual gre > interfaces. Using CARP with dc's as the carpdev, the carp i/f sticks in > INIT state when I take the physical i/f down and up. I need to ifconfig > up the carp i/f itself to get it to return to MASTER state. > > However, with the xl and gre interfaces, the carp device returns to > MASTER when I bring the carpdev back up, which is what I'd expect. > > Is there something about these dc's (or these old pcs) that makes them > difficult for CARP? > > OpenBSD 3.7-current (GENERIC) #126: Sun May 15 18:52:44 MDT 2005 > [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC > cpu0: Intel Pentium/MMX ("GenuineIntel" 586-class) 199 MHz > cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,MMX > cpu0: F00F bug workaround installed > real mem = 133804032 (130668K) > avail mem = 115552256 (112844K) > using 1658 buffers containing 6791168 bytes (6632K) of memory > mainbus0 (root) > bios0 at mainbus0: AT/286+(00) BIOS, date 08/27/97, BIOS32 rev. 0 @ > 0xffe90 > apm0 at bios0: Power Management spec V1.2 > apm0: AC on, battery charge unknown > pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000 > pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfc7b0/128 (6 entries) > pcibios0: PCI Interrupt Router at 000:07:0 ("Intel 82371FB ISA" rev > 0x00) > pcibios0: PCI bus #1 is the last bus > bios0: ROM list: 0xc0000/0x8000 > cpu0 at mainbus0 > pci0 at mainbus0 bus 0: configuration mode 1 (no bios) > pchb0 at pci0 dev 0 function 0 "Intel 82439TX System" rev 0x01 > pcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x01 > pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE" rev 0x01: DMA, > channel > 0 wired to compatibility, channel 1 wired to compatibility > wd0 at pciide0 channel 0 drive 0: <Maxtor 83240D4> > wd0: 16-sector PIO, LBA, 3089MB, 6328125 sectors > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 > atapiscsi0 at pciide0 channel 1 drive 0 > scsibus0 at atapiscsi0: 2 targets > cd0 at scsibus0 targ 0 lun 0: <NEC, CD-ROM DRIVE:288, 3.04> SCSI0 > 5/cdrom re > movable > cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 > uhci0 at pci0 dev 7 function 2 "Intel 82371AB USB" rev 0x01: irq 11 > usb0 at uhci0: USB revision 1.0 > uhub0 at usb0 > uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > "Intel 82371AB Power Mgmt" rev 0x01 at pci0 dev 7 function 3 not > configured > ppb0 at pci0 dev 14 function 0 "DEC 21152 PCI-PCI" rev 0x03 > pci1 at ppb0 bus 1 > dc0 at pci1 dev 4 function 0 "DEC 21142/3" rev 0x41: irq 11, address > 00:c0:9 > 5:e2:bd:90 > dcphy0 at dc0 phy 31: internal PHY > dc1 at pci1 dev 5 function 0 "DEC 21142/3" rev 0x41: irq 11, address > 00:c0:9 > 5:e2:bd:91 > dcphy1 at dc1 phy 31: internal PHY > dc2 at pci1 dev 6 function 0 "DEC 21142/3" rev 0x41: irq 11, address > 00:c0:9 > 5:e2:bd:92 > dcphy2 at dc2 phy 31: internal PHY > dc3 at pci1 dev 7 function 0 "DEC 21142/3" rev 0x41: irq 9, address > 00:c0:95 > :e2:bd:93 > dcphy3 at dc3 phy 31: internal PHY > xl0 at pci0 dev 15 function 0 "3Com 3c905B 100Base-TX" rev 0x30: irq 9, > addr > ess 00:04:76:1a:19:cb > exphy0 at xl0 phy 24: 3Com internal media interface > vga1 at pci0 dev 16 function 0 "S3 Trio64V2/DX" rev 0x16 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > wsdisplay0: screen 1-5 added (80x25, vt100 emulation) > isa0 at pcib0 > isadma0 at isa0 > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pcppi0 at isa0 port 0x61 > midi0 at pcppi0: <PC speaker> > spkr0 at pcppi0 > sysbeep0 at pcppi0 > lpt0 at isa0 port 0x378/4 irq 7 > npx0 at isa0 port 0xf0/16: using exception 16 > pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 > fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec > isapnp0 at isa0 port 0x279: read port 0x203 > sb1 at isapnp0 "Creative ViBRA16X PnP, CTL0043, , Audio" port > 0x220/16,0x330 > /2,0x388/4 irq 5 drq 1,3: dsp v4.16 > midi1 at sb1: <SB MPU-401 UART> > audio0 at sb1 > opl0 at sb1: model OPL3 > midi2 at opl0: <SB Yamaha OPL3> > joy0 at isapnp0 "Creative ViBRA16X PnP, CTL7005, PNPB02F, Game" port > 0x201/1 > biomask fd45 netmask ff45 ttymask ffc7 > pctr: 586-class performance counters and user-level cycle counter > enabled > dkcsum: wd0 matched BIOS disk 80 > root on wd0a > rootdev=0x0 rrootdev=0x300 rawdev=0x302 > > -- > [EMAIL PROTECTED]