Hello all,
I have recently installed OpenBSD 3.7-current (as of 07/12/05) and have selected the bsd.mp kernel since I am running a system with 2 CPUs. After looking at the dmesg output after the initial boot, I noticed the following strange lines near the bottom:

ioapic0: pin 17 shares different IPL interrupts (40..90), degraded performance ioapic0: pin 18 shares different IPL interrupts (40..50), degraded performance ioapic0: pin 19 shares different IPL interrupts (40..50), degraded performance

I have done google searches, but was unable to determine the cause of these messages. Additionally, I have sought help on the #openbsd IRC channel (freenode.net) but no one seems to be able to figure out what's going on here. The details of my particular system are spelled out in the full dmesg output, which is listed below. Specifically, I would like to know what the reason for these messages might be, whether or not they are anything I should worry about (the system is up and running, with no noticeable problems thus far), and if there is anything I can do to remedy the situation. As always, thanks in advance for your help.

Cheers,
Mike

---------- dmesg output follows ----------

OpenBSD 3.7-current (GENERIC.MP) #215: Tue Jul 12 11:00:46 MDT 2005
   [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: AMD Athlon(tm) MP 2100+ ("AuthenticAMD" 686-class, 256KB L2 cache) 1.74 GHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
real mem  = 1072730112 (1047588K)
avail mem = 972230656 (949444K)
using 4278 buffers containing 53739520 bytes (52480K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(18) BIOS, date 08/05/03, BIOS32 rev. 0 @ 0xfd670
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xfd670/0x990
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdee0/256 (14 entries)
pcibios0: no compatible PCI ICU found: ICU vendor 0x1022 product 0x7443
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc0000/0xc000 0xcc000/0x800 0xcc800/0x800 0xcd000/0x4600 0xe0000/0x4000!
mainbus0: Intel MP Specification (Version 1.4) (TYAN     PAULANER    )
cpu0 at mainbus0: apid 1 (boot processor)
cpu0: AMD Powernow: FID
cpu0: apic clock running at 266 MHz
cpu1 at mainbus0: apid 0 (application processor)
cpu1: AMD Athlon(tm) MP 2100+ ("AuthenticAMD" 686-class, 256KB L2 cache) 1.74 GHz cpu1: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
mainbus0: bus 0 is type PCI
mainbus0: bus 1 is type PCI
mainbus0: bus 2 is type PCI
mainbus0: bus 3 is type ISA
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 11, 24 pins
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "AMD 762 PCI" rev 0x11
ppb0 at pci0 dev 1 function 0 "AMD 762 PCI-PCI" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 5 function 0 "ATI Radeon 9200" rev 0x01
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
"ATI Radeon 9200 2nd" rev 0x01 at pci1 dev 5 function 1 not configured
pcib0 at pci0 dev 7 function 0 "AMD 768 ISA" rev 0x05
pciide0 at pci0 dev 7 function 1 "AMD 768 IDE" rev 0x04: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <WDC WD1200BB-00CAA1>
wd0: 16-sector PIO, LBA, 114473MB, 234441648 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
sd0 at scsibus0 targ 0 lun 0: <IOMEGA, ZIP 250, 42.S> SCSI0 0/direct removable
sd0: drive offline
atapiscsi1 at pciide0 channel 1 drive 1
scsibus1 at atapiscsi1: 2 targets
cd0 at scsibus1 targ 0 lun 0: <Memorex, DVD+R/RW 2.4x8AA, 1.72> SCSI0 5/cdrom removable
sd0(pciide0:1:0): using PIO mode 3, Ultra-DMA mode 2
cd0(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 2
"AMD 768 Power" rev 0x03 at pci0 dev 7 function 3 not configured
emu0 at pci0 dev 9 function 0 "Creative Labs SoundBlaster Live" rev 0x0a: apic 2 int 17 (irq 11)
ac97: codec id 0x83847608 (SigmaTel STAC9708/11)
ac97: codec features 18 bit DAC, 18 bit ADC, SigmaTel 3D
audio0 at emu0
"Creative Labs PCI Gameport Joystick" rev 0x0a at pci0 dev 9 function 1 not configured
ppb1 at pci0 dev 16 function 0 "AMD 768 PCI-PCI" rev 0x05
pci2 at ppb1 bus 2
ohci0 at pci2 dev 0 function 0 "AMD 768 USB" rev 0x07: apic 2 int 19 (irq 10), version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
ohci1 at pci2 dev 5 function 0 "NEC USB" rev 0x43: apic 2 int 17 (irq 11), version 1.0
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
ohci2 at pci2 dev 5 function 1 "NEC USB" rev 0x43: apic 2 int 18 (irq 9), version 1.0
usb2 at ohci2: USB revision 1.0
uhub2 at usb2
uhub2: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0 at pci2 dev 5 function 2 "NEC USB" rev 0x04: apic 2 int 19 (irq 10)
usb3 at ehci0: USB revision 2.0
uhub3 at usb3
uhub3: NEC EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 5 ports with 5 removable, self powered
pciide1 at pci2 dev 6 function 0 "HighPoint HPT36x/37x IDE" rev 0x03: DMA
pciide1: using apic 2 int 18 (irq 9) for native-PCI interrupt
wd1 at pciide1 channel 0 drive 0: <WDC WD1200JB-00CRA1>
wd1: 16-sector PIO, LBA, 114473MB, 234441648 sectors
wd1(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5
wd2 at pciide1 channel 1 drive 0: <WDC WD800BB-00CAA0>
wd2: 16-sector PIO, LBA, 76319MB, 156301488 sectors
wd2(pciide1:1:0): using PIO mode 4, Ultra-DMA mode 5
"ATI Rage XL" rev 0x27 at pci2 dev 7 function 0 not configured
xl0 at pci2 dev 8 function 0 "3Com 3c980C 100Base-TX" rev 0x78: apic 2 int 18 (irq 9), address 00:e0:81:22:5b:f4
exphy0 at xl0 phy 24: 3Com internal media interface
xl1 at pci2 dev 9 function 0 "3Com 3c980C 100Base-TX" rev 0x78: apic 2 int 19 (irq 10), address 00:e0:81:22:5b:f5
exphy1 at xl1 phy 24: 3Com internal media interface
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask 0 netmask 0 ttymask 0
ioapic0: pin 17 shares different IPL interrupts (40..90), degraded performance ioapic0: pin 18 shares different IPL interrupts (40..50), degraded performance ioapic0: pin 19 shares different IPL interrupts (40..50), degraded performance
pctr: user-level cycle counter enabled
mtrr: Pentium Pro MTRR support
apm0: disconnected
uhidev0 at uhub2 port 1 configuration 1 interface 0
uhidev0: Logitech USB Mouse, rev 1.10/6.10, addr 2, iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir.
wsmouse0 at ums0 mux 0
umass0 at uhub3 port 3 configuration 1 interface 0
umass0: Behavior Tech. Computer USB 2.0 Storage Device, rev 2.00/1.03, addr 2
umass0: using SCSI over Bulk-Only
scsibus2 at umass0: 2 targets
cd1 at scsibus2 targ 1 lun 0: <CDWRITER, IDE5232, 0009> SCSI0 5/cdrom removable
dkcsum: wd0 matched BIOS disk 80
dkcsum: read of sd0 failed (0)
dkcsum: wd1 matched BIOS disk 81
wd2: no disk label
dkcsum: wd2 matched BIOS disk 82
root on wd1a
rootdev=0x10 rrootdev=0x310 rawdev=0x312
cpu1: AMD Powernow: FID
umass1 at uhub1 port 3 configuration 1 interface 0
umass1: SCM Microsystems Inc. eUSB ORCA Quad Reader, rev 1.10/5.03, addr 2
umass1: using SCSI over Bulk-Only
scsibus3 at umass1: 2 targets
umass1: Invalid CSW: tag 0 should be 50
sd1 at scsibus3 targ 1 lun 0: <eUSB, SD-MS-SM, 5.03> SCSI2 0/direct removable
umass1: Invalid CSW: tag 0 should be 52
umass1: Invalid CSW: tag 0 should be 54
sd1: drive offline
sd2 at scsibus3 targ 1 lun 1: <eUSB, SD-MS-SM, 5.03> SCSI2 0/direct removable
sd2: drive offline

--------- end dmesg output ----------

_________________________________________________________________
Dont just search. Find. Check out the new MSN Search! http://search.msn.click-url.com/go/onm00200636ave/direct/01/

Reply via email to