Good afternoon,
My apologies - the previous post was a little mangled.
I have just attempted an install of the latest snapshot cd51.iso - dated
07/04/2012 5:55:00 PM on some new HP 360 servers.
I am able to boot of the CD, but the boot hangs immediately after the following
line is displayed:
brgphy3 at bnx3 phy1: BCM5709 10/100/100baseT PHY, rev. 8
(see full dmesg below)
This is also the case when trying to install by booting off the OpenBSD 5.0 CD
disk 1 (and cd50.iso).
I was able to install on the HP 360 servers by moving drives over from an HP
120 (which didn't have the same problem) with BSD already installed, booting
off bsd.rd from disk, and reinstalling over the network, and subsequent
installations booting to bsd.rd on disk to sd1 and swapping drives, etc.
As such, I have OpenBSD 5.0 running on our HP 360 servers, but have never been
able to boot and install from a USB attached CD (or USB memory stick).
I should mention that when installing I also have a USB attached key board in
addition to the USB attached CD Drive (see dmesg output below).
This is an inconvenience more than anything, but it might point to some
underlying issues?
Has anyone seen similar problems?
Many thanks.
Rob
= = = = = USB Keyboard attach, detach, and reattach = = = = =
uhidev2 at uhub4 port 1 configuration 1 interface 0 "GASIA GASIA USB KB Pro"
rev 1.10/2.10 addr 2
uhidev2: iclass 3/1
ukbd1 at uhidev2: 8 modifier keys, 6 key codes
wskbd2 at ukbd1 mux 1
wskbd2: connecting to wsdisplay0
uhidev3 at uhub4 port 1 configuration 1 interface 1 "GASIA GASIA USB KB Pro"
rev 1.10/2.10 addr 2
uhidev3: iclass 3/0, 2 report ids
uhid0 at uhidev3 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev3 reportid 2: input=1, output=0, feature=0
wskbd2: disconnecting from wsdisplay0
wskbd2 detached
ukbd1 detached
uhidev2 detached
uhid0 detached
uhid1 detached
uhidev3 detached
uhidev2 at uhub4 port 1 configuration 1 interface 0 "GASIA GASIA USB KB Pro"
rev 1.10/2.10 addr 2
uhidev2: iclass 3/1
ukbd1 at uhidev2: 8 modifier keys, 6 key codes
wskbd2 at ukbd1 mux 1
wskbd2: connecting to wsdisplay0
uhidev3 at uhub4 port 1 configuration 1 interface 1 "GASIA GASIA USB KB Pro"
rev 1.10/2.10 addr 2
uhidev3: iclass 3/0, 2 report ids
uhid0 at uhidev3 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev3 reportid 2: input=1, output=0, feature=0
= = = = = USB attached CD Drive = = = = =
wskbd2: disconnecting from wsdisplay0
wskbd2 detached
ukbd1 detached
uhidev2 detached
uhid0 detached
uhid1 detached
uhidev3 detached
uhidev2 at uhub4 port 1 configuration 1 interface 0 "GASIA GASIA USB KB Pro"
rev 1.10/2.10 addr 2
uhidev2: iclass 3/1
ukbd1 at uhidev2: 8 modifier keys, 6 key codes
wskbd2 at ukbd1 mux 1
wskbd2: connecting to wsdisplay0
uhidev3 at uhub4 port 1 configuration 1 interface 1 "GASIA GASIA USB KB Pro"
rev 1.10/2.10 addr 2
uhidev3: iclass 3/0, 2 report ids
uhid0 at uhidev3 reportid 1: input=2, output=0, feature=0
uhid1 at uhidev3 reportid 2: input=1, output=0, feature=0
umass0 at uhub1 port 7 configuration 1 interface 0 "MediaTek Inc MT1836" rev
2.00/0.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus3 at umass0: 2 targets, initiator 0
cd0 at scsibus3 targ 1 lun 0: <HL-DT-ST, DVDRAM GP10NW20, 1.03> SCSI0 5/cdrom
removable serial.0e8d1836B3H5824_
cd0 detached
scsibus3 detached
umass0 detached
= = = = = dmesg (USB devices were not present at reboot) = = = = =
OpenBSD 5.0 (GENERIC.MP) #59: Wed Aug 17 10:19:44 MDT 2011
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Intel(R) Xeon(R) CPU E5620 @ 2.40GHz ("GenuineIntel" 686-class) 2.41 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACP
I,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,PCLMUL,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,
PDCM,DCA,SSE4.1,SSE4.2,POPCNT,AES
real mem = 3747340288 (3573MB)
avail mem = 3675979776 (3505MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 12/31/99, BIOS32 rev. 0 @ 0xf0000, SMBIOS
rev. 2.7 @
0xdf7fe000 (127 entries)
bios0: vendor HP version "P68" date 05/05/2011
bios0: HP ProLiant DL360 G7
acpi0 at bios0: rev 2
acpi0: sleep states S0 S4 S5
acpi0: tables DSDT FACP SPCR MCFG HPET FFFF SPMI ERST APIC SRAT FFFF BERT HEST
DMAR SSDT SS
DT SSDT SSDT SSDT
acpi0: wakeup devices
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-63
acpihpet0 at acpi0: 14318179 Hz
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: apic clock running at 133MHz
cpu1 at mainbus0: apid 20 (application processor)
cpu1: Intel(R) Xeon(R) CPU E5620 @ 2.40GHz ("GenuineIntel" 686-class) 2.41 GHz
cpu1:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACP
I,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,PCLMUL,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,
PDCM,DCA,SSE4.1,SSE4.2,POPCNT,AES
cpu2 at mainbus0: apid 2 (application processor)
cpu2: Intel(R) Xeon(R) CPU E5620 @ 2.40GHz ("GenuineIntel" 686-class) 2.41 GHz
cpu2:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACP
I,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,PCLMUL,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,
PDCM,DCA,SSE4.1,SSE4.2,POPCNT,AES
cpu3 at mainbus0: apid 18 (application processor)
cpu3: Intel(R) Xeon(R) CPU E5620 @ 2.40GHz ("GenuineIntel" 686-class) 2.41 GHz
cpu3:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACP
I,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,PCLMUL,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,
PDCM,DCA,SSE4.1,SSE4.2,POPCNT,AES
cpu4 at mainbus0: apid 1 (application processor)
cpu4: Intel(R) Xeon(R) CPU E5620 @ 2.40GHz ("GenuineIntel" 686-class) 2.41 GHz
cpu4:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACP
I,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,PCLMUL,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,
PDCM,DCA,SSE4.1,SSE4.2,POPCNT,AES
cpu5 at mainbus0: apid 21 (application processor)
cpu5: Intel(R) Xeon(R) CPU E5620 @ 2.40GHz ("GenuineIntel" 686-class) 2.41 GHz
cpu5:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACP
I,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,PCLMUL,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,
PDCM,DCA,SSE4.1,SSE4.2,POPCNT,AES
cpu6 at mainbus0: apid 3 (application processor)
cpu6: Intel(R) Xeon(R) CPU E5620 @ 2.40GHz ("GenuineIntel" 686-class) 2.41 GHz
cpu6:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACP
I,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,PCLMUL,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,
PDCM,DCA,SSE4.1,SSE4.2,POPCNT,AES
cpu7 at mainbus0: apid 19 (application processor)
cpu7: Intel(R) Xeon(R) CPU E5620 @ 2.40GHz ("GenuineIntel" 686-class) 2.41 GHz
cpu7:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACP
I,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,PCLMUL,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,
PDCM,DCA,SSE4.1,SSE4.2,POPCNT,AES
ioapic0 at mainbus0: apid 8 pa 0xfec00000, version 20, 24 pins
ioapic1 at mainbus0: apid 0 pa 0xfec80000, version 20, 24 pins
acpiprt0 at acpi0: bus 1 (IP2P)
acpiprt1 at acpi0: bus 17 (IPT1)
acpiprt2 at acpi0: bus -1 (IPT3)
acpiprt3 at acpi0: bus 2 (IPT5)
acpiprt4 at acpi0: bus 5 (PT01)
acpiprt5 at acpi0: bus 9 (PT03)
acpiprt6 at acpi0: bus 13 (PT04)
acpiprt7 at acpi0: bus 14 (PT05)
acpiprt8 at acpi0: bus 15 (PT06)
acpiprt9 at acpi0: bus 3 (PT07)
acpiprt10 at acpi0: bus 4 (PT08)
acpiprt11 at acpi0: bus 6 (PT09)
acpiprt12 at acpi0: bus 16 (PT0A)
acpiprt13 at acpi0: bus 0 (PCI0)
acpicpu0 at acpi0: C3, C3, C1
acpicpu1 at acpi0: C3, C3, C1
acpicpu2 at acpi0: C3, C3, C1
acpicpu3 at acpi0: C3, C3, C1
acpicpu4 at acpi0: C3, C3, C1
acpicpu5 at acpi0: C3, C3, C1
acpicpu6 at acpi0: C3, C3, C1
acpicpu7 at acpi0: C3, C3, C1
acpitz0 at acpi0: critical temperature is 31 degC
bios0: ROM list: 0xc0000/0xb000 0xcb000/0x2e00! 0xcde00/0x4000
ipmi at mainbus0 not configured
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 5520 Host" rev 0x13
ppb0 at pci0 dev 1 function 0 "Intel X58 PCIE" rev 0x13
pci1 at ppb0 bus 5
ciss0 at pci1 dev 0 function 0 "Hewlett-Packard Smart Array" rev 0x01: apic 0
int 4
ciss0: 1 LD, HW rev 2, FW 5.14/5.14, 64bit fifo rro
scsibus0 at ciss0: 1 targets
sd0 at scsibus0 targ 0 lun 0: <HP, LOGICAL VOLUME, 5.14> SCSI3 0/direct fixed
sd0: 69973MB, 512 bytes/sector, 143305920 sectors
ppb1 at pci0 dev 2 function 0 "Intel X58 PCIE" rev 0x13
pci2 at ppb1 bus 12
ppb2 at pci0 dev 3 function 0 "Intel X58 PCIE" rev 0x13
pci3 at ppb2 bus 9
ppb3 at pci0 dev 4 function 0 "Intel X58 PCIE" rev 0x13
pci4 at ppb3 bus 13
ppb4 at pci0 dev 5 function 0 "Intel X58 PCIE" rev 0x13
pci5 at ppb4 bus 14
ppb5 at pci0 dev 6 function 0 "Intel X58 PCIE" rev 0x13
pci6 at ppb5 bus 15
ppb6 at pci0 dev 7 function 0 "Intel X58 PCIE" rev 0x13
pci7 at ppb6 bus 3
bnx0 at pci7 dev 0 function 0 "Broadcom BCM5709" rev 0x20: apic 0 int 6
bnx1 at pci7 dev 0 function 1 "Broadcom BCM5709" rev 0x20: apic 0 int 13
ppb7 at pci0 dev 8 function 0 "Intel X58 PCIE" rev 0x13
pci8 at ppb7 bus 4
bnx2 at pci8 dev 0 function 0 "Broadcom BCM5709" rev 0x20: apic 0 int 7
bnx3 at pci8 dev 0 function 1 "Broadcom BCM5709" rev 0x20: apic 0 int 15
ppb8 at pci0 dev 9 function 0 "Intel X58 PCIE" rev 0x13
pci9 at ppb8 bus 6
ppb9 at pci0 dev 10 function 0 "Intel X58 PCIE" rev 0x13
pci10 at ppb9 bus 16
pchb1 at pci0 dev 13 function 0 vendor "Intel", unknown product 0x343a rev 0x13
pchb2 at pci0 dev 13 function 1 vendor "Intel", unknown product 0x343b rev 0x13
pchb3 at pci0 dev 13 function 2 vendor "Intel", unknown product 0x343c rev 0x13
pchb4 at pci0 dev 13 function 3 vendor "Intel", unknown product 0x343d rev 0x13
pchb5 at pci0 dev 13 function 4 "Intel 5520/X58 QuickPath" rev 0x13
pchb6 at pci0 dev 13 function 5 "Intel 5520 QuickPath" rev 0x13
pchb7 at pci0 dev 13 function 6 vendor "Intel", unknown product 0x341a rev 0x13
pchb8 at pci0 dev 14 function 0 vendor "Intel", unknown product 0x341c rev 0x13
pchb9 at pci0 dev 14 function 1 vendor "Intel", unknown product 0x341d rev 0x13
pchb10 at pci0 dev 14 function 2 vendor "Intel", unknown product 0x341e rev 0x13
pchb11 at pci0 dev 14 function 3 vendor "Intel", unknown product 0x341f rev 0x13
pchb12 at pci0 dev 14 function 4 vendor "Intel", unknown product 0x3439 rev 0x13
"Intel X58 Misc" rev 0x13 at pci0 dev 20 function 0 not configured
"Intel X58 GPIO" rev 0x13 at pci0 dev 20 function 1 not configured
"Intel X58 RAS" rev 0x13 at pci0 dev 20 function 2 not configured
ppb10 at pci0 dev 28 function 0 "Intel 82801JI PCIE" rev 0x00
pci11 at ppb10 bus 17
ppb11 at pci0 dev 28 function 4 "Intel 82801JI PCIE" rev 0x00
pci12 at ppb11 bus 2
"Hewlett-Packard iLO3 Slave" rev 0x04 at pci12 dev 0 function 0 not configured
"Hewlett-Packard iLO3 Management" rev 0x04 at pci12 dev 0 function 2 not
configured
uhci0 at pci12 dev 0 function 4 "Hewlett-Packard USB" rev 0x01: apic 8 int 17
usb0 at uhci0: USB revision 1.0
uhub0 at usb0 "Hewlett-Packard UHCI root hub" rev 1.00/1.00 addr 1
uhci1 at pci0 dev 29 function 0 "Intel 82801JI USB" rev 0x00: apic 8 int 20
uhci2 at pci0 dev 29 function 1 "Intel 82801JI USB" rev 0x00: apic 8 int 23
uhci3 at pci0 dev 29 function 2 "Intel 82801JI USB" rev 0x00: apic 8 int 22
uhci4 at pci0 dev 29 function 3 "Intel 82801JI USB" rev 0x00: apic 8 int 23
ehci0 at pci0 dev 29 function 7 "Intel 82801JI USB" rev 0x00: apic 8 int 20
usb1 at ehci0: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb12 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x90
pci13 at ppb12 bus 1
vga1 at pci13 dev 3 function 0 "ATI ES1000" rev 0x02
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
radeondrm0 at vga1: apic 8 int 23
drm0 at radeondrm0
pcib0 at pci0 dev 31 function 0 "Intel 82801JIB LPC" rev 0x00
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci3: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb5 at uhci4: USB revision 1.0
uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
com1: probed fifo depth: 0 bytes
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
mtrr: Pentium Pro MTRR support
uhidev0 at uhub0 port 1 configuration 1 interface 0 "HP Virtual Keyboard" rev
1.10/0.02 add
r 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes, country code 33
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub0 port 1 configuration 1 interface 1 "HP Virtual Keyboard" rev
1.10/0.02 add
r 2
uhidev1: iclass 3/1
ums0 at uhidev1: 3 buttons
wsmouse0 at ums0 mux 0
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
root on sd0a (a1adc58327a25ce1.a) swap on sd0b dump on sd0b
bnx0: address ...
brgphy0 at bnx0 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8
bnx1: address ...
brgphy1 at bnx1 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8
bnx2: address ...
brgphy2 at bnx2 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8
bnx3: address ...
brgphy3 at bnx3 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8
carp: carp1 demoted group carp by 1 to 129 (carpdev)
carp: pfsync0 demoted group carp by 1 to 130 (pfsync bulk start)
carp: pfsync0 demoted group pfsync by 1 to 1 (pfsync bulk start)
carp: carp1 demoted group carp by -1 to 129 (carpdev)
carp: carp1 demoted group paz by -1 to 0 (carpdev)
