Hi,
I have a problem with a Digitus USB 2.0 repeater cable in combination with a
Soekris net5501 running OpenBSD 5.2 (see full dmesg at the very end of this
mail).
The aim is to improve the position of a UTMS stick ("Option GlobeTrotter HSDPA
ICON225 USB") via the repeater cable. The UMTS stick works when directly
attached to the Soekris net5501:
umsm0 at uhub1 port 1 configuration 1 interface 0 "Option N.V. Globetrotter
HSDPA Modem" rev 1.10/0.00 addr 2
umsm0 detached
umsm0 at uhub1 port 1 configuration 1 interface 0 "Option N.V. Globetrotter
HSDPA Modem" rev 1.10/0.00 addr 2
ucom0 at umsm0
umsm1 at uhub1 port 1 configuration 1 interface 1 "Option N.V. Globetrotter
HSDPA Modem" rev 1.10/0.00 addr 2
ucom1 at umsm1
umsm2 at uhub1 port 1 configuration 1 interface 2 "Option N.V. Globetrotter
HSDPA Modem" rev 1.10/0.00 addr 2
ucom2 at umsm2
usbdevs -v:
Controller /dev/usb0:
addr 1: high speed, self powered, config 1, EHCI root hub(0x0000), AMD(0x1022),
rev 1.00
port 1 powered
port 2 powered
port 3 powered
port 4 powered
Controller /dev/usb1:
addr 1: full speed, self powered, config 1, OHCI root hub(0x0000), AMD(0x1022),
rev 1.00
port 1 addr 2: full speed, power 500 mA, config 1, Globetrotter HSDPA
Modem(0x6971), Option N.V.(0x0af0), rev 0.00, iSerialNumber Serial Number
port 2 powered
port 3 powered
port 4 powered
Attaching the repeater cable alone works as well:
uhub2 at uhub0 port 1 "Terminus Technology product 0x0101" rev 2.00/1.11 addr 2
usbdevs -v:
Controller /dev/usb0:
addr 1: high speed, self powered, config 1, EHCI root hub(0x0000), AMD(0x1022),
rev 1.00
port 1 addr 2: high speed, self powered, config 1, USB 2.0 Hub(0x0101),
Terminus Technology(0x1a40), rev 1.11
port 1 powered
port 2 powered
port 3 powered
port 4 powered
port 2 powered
port 3 powered
port 4 powered
Controller /dev/usb1:
addr 1: full speed, self powered, config 1, OHCI root hub(0x0000), AMD(0x1022),
rev 1.00
port 1 powered
port 2 powered
port 3 powered
port 4 powered
However, the problem occurs when I attach the repeater cable with the UMTS
stick at its end. The stick is not recognized anymore.
uhub2 at uhub0 port 1 "Terminus Technology product 0x0101" rev 2.00/1.11 addr 2
If I boot with the repeater cable and UMTS stick already attached:
uhub2 at uhub0 port 1 "Terminus Technology product 0x0101" rev 2.00/1.11 addr 2
uhub2: device problem, disabling port 1
Do you have any ideas how to address this? (Yes, I have tested the
repeater cable on a different machine (running Linux) and it works there
with the same combination of cable and UMTS stick).
Thanks!
Best regards,
Ingo
dmesg:
OpenBSD 5.2 (GENERIC) #278: Wed Aug 1 10:04:16 MDT 2012
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class) 434
MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX,MMXX,3DNOW2,3DNOW
real mem = 267972608 (255MB)
avail mem = 252731392 (241MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 20/80/26, BIOS32 rev. 0 @ 0xfac40
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0xa800
cpu0 at mainbus0: (uniprocessor)
amdmsr0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
io address conflict 0x6100/0x100
io address conflict 0x6200/0x200
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x30
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
vr0 at pci0 dev 6 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11, address
00:00:24:c9:31:80
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr1 at pci0 dev 7 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 5, address
00:00:24:c9:31:81
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr2 at pci0 dev 8 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 9, address
00:00:24:c9:31:82
ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr3 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12, address
00:00:24:c9:31:83
ukphy3 at vr3 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
glxpcib0 at pci0 dev 20 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, 32-bit
3579545Hz timer, watchdog, gpio, i2c
gpio0 at glxpcib0: 32 pins
iic0 at glxpcib0
pciide0 at pci0 dev 20 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFB-512>
wd0: 4-sector PIO, LBA, 488MB, 1000944 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 21 function 0 "AMD CS5536 USB" rev 0x02: irq 15, version 1.0,
legacy support
ehci0 at pci0 dev 21 function 1 "AMD CS5536 USB" rev 0x02: irq 15
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
isa0 at glxpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
gpio1 at nsclpcsio0: 29 pins
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
mtrr: K6-family MTRR support (2 registers)
vscsi0 at root
scsibus0 at vscsi0: 256 targets
softraid0 at root
scsibus1 at softraid0: 256 targets
root on wd0a (2c90b6fdf6bb14fc.a) swap on wd0b dump on wd0b
