a speedy reply pointed me to incorrect setting in /etc/ttys Cheers! --patrick
On 1/11/14, patrick keshishian <pkesh...@gmail.com> wrote: > Hi, > > This is my first experience with installing on one of these > boards. I got today's i386 snapshot (Jan 11, 2014) and installed > successfully on a CF card. > > After placing the CF in the unit, it seems to boot up fine > after setting: > boot> stty com0 38400 > boot> set tty com0 > > However, it stops right before displaying the login prompt: > > switching console to com0 > >> OpenBSD/i386 BOOT 3.25 > boot> > loadrandom: hd0a:/etc/random.seed > booting hd0a:/bsd: 9276028+1082796 [72+404624+398274]=0xaa5260 > entry point at 0x200120 > > [ using 803384 bytes of bsd ELF symbol table ] > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > Copyright (c) 1995-2014 OpenBSD. All rights reserved. > http://www.OpenBSD.org > [... full output at eom] > starting network daemons: sshd sendmail sndiod. > starting local daemons: cron. > Sat Jan 11 20:12:23 PST 2014 > > > it just sits there. Sending it BREAK does nothing. > > Any ideas what I may be doing incorrectly? > > --patrick > > > PC Engines ALIX.2 v0.99h > 640 KB Base Memory > 261120 KB Extended Memory > > 01F0 Master 848A ULTIMATE CF CARD > Phys C/H/S 16383/16/63 Log C/H/S 1892/255/63 LBA > Using drive 0, partition 3. > Loading..... > probing: pc0 com0 com1 pci mem[640K 255M a20=on] > disk: hd0+ >>> OpenBSD/i386 BOOT 3.25 > boot> > loadrandom: hd0a:/etc/random.seed > booting hd0a:/bsd: 9276028+1082796 [72+404624+398274]=0xaa5260 > entry point at 0x200120 > PC Engines ALIX.2 v0.99h > 640 KB Base Memory > 31744PC Engines ALIX.2 v0.99h > 640 KB Base Memory > 261120 KB Extended Memory > > 01F0 Master 848A ULTIMATE CF CARD > Phys C/H/S 16383/16/63 Log C/H/S 1892/255/63 LBA > Using drive 0, partition 3. > Loading..... > probing: pc0 com0 com1 pci mem[640K 255M a20=on] > disk: hd0+ >>> OpenBSD/i386 BOOT 3.25 > boot> stty com0 38400 > boot> set tty com0 > switching console to com0 > >> OpenBSD/i386 BOOT 3.25 > boot> > loadrandom: hd0a:/etc/random.seed > booting hd0a:/bsd: 9276028+1082796 [72+404624+398274]=0xaa5260 > entry point at 0x200120 > > [ using 803384 bytes of bsd ELF symbol table ] > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > Copyright (c) 1995-2014 OpenBSD. All rights reserved. > http://www.OpenBSD.org > > OpenBSD 5.4-current (GENERIC) #224: Sat Jan 11 00:32:57 MST 2014 > dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC > cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" > 586-class) 499 MHz > cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX,MMXX,3DNOW2,3DNOW > real mem = 267943936 (255MB) > avail mem = 251678720 (240MB) > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 11/05/08, BIOS32 rev. 0 @ 0xfd088 > pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000 > pcibios0: pcibios_get_intr_routing - function not supported > pcibios0: PCI IRQ Routing information unavailable. > pcibios0: PCI bus #0 is the last bus > bios0: ROM list: 0xe0000/0xa800 > cpu0 at mainbus0: (uniprocessor) > mtrr: K6-family MTRR support (2 registers) > pci0 at mainbus0 bus 0: configuration mode 1 (bios) > pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x33 > glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES > vr0 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 10, > address 00:0d:b9:2f:89:e4 > ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x004063, model 0x0034 > vr1 at pci0 dev 10 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11, > address 00:0d:b9:2f:89:e5 > ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x004063, model 0x0034 > vr2 at pci0 dev 11 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 15, > address 00:0d:b9:2f:89:e6 > ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI > 0x004063, model 0x0034 > glxpcib0 at pci0 dev 15 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, > 32-bit 3579545Hz timer, watchdog, gpio, i2c > gpio0 at glxpcib0: 32 pins > iic0 at glxpcib0 > maxtmp0 at iic0 addr 0x4c: lm86 > pciide0 at pci0 dev 15 function 2 "AMD CS5536 IDE" rev 0x01: DMA, > channel 0 wired to compatibility, channel 1 wired to compatibility > wd0 at pciide0 channel 0 drive 0: <ULTIMATE CF CARD> > wd0: 1-sector PIO, LBA48, 14847MB, 30408336 sectors > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 > pciide0: channel 1 ignored (disabled) > ohci0 at pci0 dev 15 function 4 "AMD CS5536 USB" rev 0x02: irq 12, > version 1.0, legacy support > ehci0 at pci0 dev 15 function 5 "AMD CS5536 USB" rev 0x02: irq 12 > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1 > isa0 at glxpcib0 > isadma0 at isa0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > com0: console > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > pcppi0 at isa0 port 0x61 > spkr0 at pcppi0 > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > usb1 at ohci0: USB revision 1.0 > uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1 > nvram: invalid checksum > vscsi0 at root > scsibus0 at vscsi0: 256 targets > softraid0 at root > scsibus1 at softraid0: 256 targets > root on wd0a (530c32759ec43d2d.a) swap on wd0b dump on wd0b > WARNING: / was not properly unmounted > clock: unknown CMOS layout > Automatic boot in progress: starting file system checks. > /dev/rwd0a: 2004 files, 23066 used, 152524 free (44 frags, 19060 > blocks, 0.0% fragmentation) > /dev/rwd0a: MARKING FILE SYSTEM CLEAN > /dev/rwd0g: 17 files, 291 used, 514132 free (20 frags, 64264 blocks, > 0.0% fragmentation) > /dev/rwd0g: MARKING FILE SYSTEM CLEAN > /dev/rwd0d: 5 files, 4 used, 514531 free (35 frags, 64312 blocks, 0.0% > fragmentation) > /dev/rwd0d: MARKING FILE SYSTEM CLEAN > /dev/rwd0f: 22762 files, 267407 used, 2311336 free (2080 frags, 288657 > blocks, 0.1% fragmentation) > /dev/rwd0f: MARKING FILE SYSTEM CLEAN > /dev/rwd0e: 424 files, 2317 used, 512106 free (26 frags, 64010 blocks, > 0.0% fragmentation) > /dev/rwd0e: MARKING FILE SYSTEM CLEAN > setting tty flags > wsconsctl: /dev/wskbd0: Device not configured > pf enabled > starting network > starting early daemons: syslogd pflogd. > starting RPC daemons:. > savecore: no core dump > checking quotas: done. > clearing /tmp > starting pre-securelevel daemons:. > setting kernel security level: kern.securelevel: 0 -> 1 > creating runtime link editor directory cache. > preserving editor files. > starting network daemons: sshd sendmail sndiod. > starting local daemons: cron. > Sat Jan 11 20:12:23 PST 2014