I know it's ancient and minimal hardware, but I've been tinkering with
OpenBSD 5.5 on a Nokia IP260 with an 8GB compact flash. The OS was
installed on the compact flash using a card reader on a Dell laptop.
The OS boots and networking works as long as I specify the MAC using
lladdr in hostname.xxx and use duids. If you don't use duids the
partitions will not mount when the compact flash is moved from the
laptop to the IP260. But I see some errors on an 8GB compact flash that
I didn't see with a 1GB compact flash. Could it be the 8GB compact
flash is more than what the IP260 supported? Here's the dmesg
OpenBSD 5.5-current (GENERIC) #104: Sun May 11 07:51:32 MDT 2014
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Celeron(TM) CPU 400MHz ("GenuineIntel" 686-class) 401 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PSE36,MMX,FXSR,SSE,PERF
real mem = 536379392 (511MB)
avail mem = 515194880 (491MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: PC BIOS, date //
pcibios at bios0 function 0x1a not configured
bios0: ROM list: 0xe0000/0x10000!
cpu0 at mainbus0: (uniprocessor)
mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82815 Host" rev 0x04
intelagp0 at pchb0
agp0 at intelagp0: aperture at 0xf8000000, size 0x2400000
ppb0 at pci0 dev 1 function 0 "Intel 82815 AGP" rev 0x04
pci1 at ppb0 bus 1
ppb1 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x05
pci2 at ppb1 bus 2
ubsec0 at pci2 dev 0 function 0 "Broadcom 5823" rev 0x01: 3DES MD5 SHA1
AES RNG PK, irq 10
cbb0 at pci2 dev 1 function 0 "TI PCI1520 CardBus" rev 0x01: irq 11,
CardBus support disabled
cbb1 at pci2 dev 1 function 1 "TI PCI1520 CardBus" rev 0x01: irq 11,
CardBus support disabled
fxp0 at pci2 dev 2 function 0 "Intel 82559ER" rev 0x10, i82551: irq 5,
address 00:00:00:00:00:00
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
fxp1 at pci2 dev 3 function 0 "Intel 82559ER" rev 0x10, i82551: irq 6,
address 00:00:00:00:00:00
inphy1 at fxp1 phy 1: i82555 10/100 PHY, rev. 4
fxp2 at pci2 dev 4 function 0 "Intel 82559ER" rev 0x10, i82551: irq 7,
address 00:00:00:00:00:00
inphy2 at fxp2 phy 1: i82555 10/100 PHY, rev. 4
fxp3 at pci2 dev 5 function 0 "Intel 82559ER" rev 0x10, i82551: irq 9,
address 00:00:00:00:00:00
inphy3 at fxp3 phy 1: i82555 10/100 PHY, rev. 4
cbb0: bad Vcc request. sock_ctrl 0x400, sock_status 0x30000206
cardslot0 at cbb0 slot 0 flags 0
pcmcia0 at cardslot0
cardslot1 at cbb1 slot 1 flags 0
pcmcia1 at cardslot1
ichpcib0 at pci0 dev 31 function 0 "Intel 82801BA LPC" rev 0x05: PM disabled
pciide0 at pci0 dev 31 function 1 "Intel 82801BA IDE" rev 0x05: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFHNJC-008G>
wd0: 1-sector PIO, LBA48, 7629MB, 15625216 sectors
wd1 at pciide0 channel 0 drive 1: <FUJITSU MHV2040AS>
wd1: 16-sector PIO, LBA, 38154MB, 78140160 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
ichiic0 at pci0 dev 31 function 3 "Intel 82801BA SMBus" rev 0x05: irq 9
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 256MB SDRAM non-parity PC133CL2
spdmem1 at iic0 addr 0x51: 256MB SDRAM non-parity PC133CL2
isa0 at ichpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4: polled
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
gpio0 at nsclpcsio0: 29 pins
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
nvram: invalid checksum
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
wd0(pciide0:0:0): timeout
type: ata
c_bcount: 512
c_skip: 0
pciide0:0:0: bus-master DMA error: missing interrupt, status=0x61
wd0c: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
wd0(pciide0:0:0): timeout
type: ata
c_bcount: 512
c_skip: 0
pciide0:0:0: bus-master DMA error: missing interrupt, status=0x61
wd0: transfer error, downgrading to Ultra-DMA mode 1
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 1
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
wd0c: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
wd0(pciide0:0:0): timeout
type: ata
c_bcount: 512
c_skip: 0
pciide0:0:0: bus-master DMA error: missing interrupt, status=0x61
wd0: transfer error, downgrading to Ultra-DMA mode 0
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 0
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
wd0c: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
wd0(pciide0:0:0): timeout
type: ata
c_bcount: 512
c_skip: 0
pciide0:0:0: bus-master DMA error: missing interrupt, status=0x61
wd0: transfer error, downgrading to DMA mode 2
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
wd0c: device timeout reading fsbn 0 (wd0 bn 0; cn 0 tn 0 sn 0), retrying
wd0: soft error (corrected)
wd0(pciide0:0:0): timeout
type: ata
c_bcount: 512
c_skip: 0
pciide0:0:0: bus-master DMA error: missing interrupt, status=0x61
wd0: transfer error, downgrading to PIO mode 4
wd0(pciide0:0:0): using PIO mode 4
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
wd0c: device timeout reading fsbn 65 (wd0 bn 65; cn 0 tn 1 sn 2), retrying
wd0: soft error (corrected)
root on wd0a (511531c0c5c7c075.a) swap on wd0b dump on wd0b
clock: unknown CMOS layout
