I've not been able to establish a wireless connection lately on urtw0 on a yeeloong. ifconfig keeps showing a status of 'no network' on urtw0 both for the local wireless network here and another wifi network I've tried that used to work. The indicator light for the wireless device is on and 'ifconfig urtw0 scan' appears to show that the network is available. I try to connect using:
ifconfig urtw0 nwid MYWLAN chan 11 mode 11g wpakey MYWPAKEY This access point itself is running a snapshot but on i386 instead and the nwid, wpakey, channel, and mode all seem to match what I set with ifconfig on the yeeloong. And I can connect to this network with another platform. The cabled interface (rl0) works fine. What do I need to change to get urtw0 to finish connecting and show a status of 'active' ? Regards, /Lars [ using 487264 bytes of bsd ELF symbol table ] Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2014 OpenBSD. All rights reserved. http://www.OpenBSD.org OpenBSD 5.6-current (GENERIC) #159: Thu Oct 30 19:20:44 MDT 2014 dera...@loongson.openbsd.org:/usr/src/sys/arch/loongson/compile/GENERIC real mem = 1073741824 (1024MB) avail mem = 1058701312 (1009MB) mainbus0 at root: Lemote Yeeloong cpu0 at mainbus0: STC Loongson2F CPU 797 MHz, STC Loongson2F FPU cpu0: cache L1-I 64KB D 64KB 4 way, L2 512KB 4 way bonito0 at mainbus0: memory and PCI-X controller, rev 1 pci0 at bonito0 bus 0 rl0 at pci0 dev 7 function 0 "Realtek 8139" rev 0x10: irq 5, address 00:23:8b:59:df:48 rlphy0 at rl0 phy 0: RTL internal PHY smfb0 at pci0 dev 8 function 0 "Silicon Motion LynxEM+" rev 0xb0 wsdisplay0 at smfb0 mux 1: console (std, vt100 emulation) glxpcib0 at pci0 dev 14 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, 32-bit 3579545Hz timer, watchdog, gpio, i2c isa0 at glxpcib0 pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pms0 at pckbc0 (aux slot) pckbc0: using irq 12 for aux slot wsmouse0 at pms0 mux 0 mcclock0 at isa0 port 0x70/2: mc146818 or compatible ykbec0 at isa0 port 0x381/3 gpio1 at glxpcib0: 32 pins iic at glxpcib0 not configured glxclk0 at glxpcib0: clock, prof pciide0 at pci0 dev 14 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility wd0 at pciide0 channel 0 drive 0: <ULTIMATE CF CARD 1GB> wd0: 1-sector PIO, LBA, 991MB, 2030112 sectors wd0(pciide0:0:0): using PIO mode 4, DMA mode 2 pciide0: channel 1 ignored (disabled) auglx0 at pci0 dev 14 function 3 "AMD CS5536 Audio" rev 0x01: isa irq 9, CS5536 AC97 ac97: codec id 0x414c4760 (Avance Logic ALC655 rev 0) audio0 at auglx0 ohci0 at pci0 dev 14 function 4 "AMD CS5536 USB" rev 0x02: isa irq 11, version 1.0, legacy support ehci0 at pci0 dev 14 function 5 "AMD CS5536 USB" rev 0x02: isa irq 11 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1 usb1 at ohci0: USB revision 1.0 uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1 apm0 at mainbus0 umass0 at uhub0 port 1 configuration 1 interface 0 "Generic USB2.0-CRW" rev 2.00/58.87 addr 2 umass0: using SCSI over Bulk-Only scsibus0 at umass0: 2 targets, initiator 0 sd0 at scsibus0 targ 1 lun 0: <Generic-, Multi-Card, 1.00> SCSI0 0/direct removable serial.0bda0158114173400000 urtw0 at uhub0 port 4 "Realtek RTL8187B" rev 2.00/2.00 addr 3 urtw0: RTL8187B rev E, address 00:17:c4:4d:ed:56 vscsi0 at root scsibus1 at vscsi0: 256 targets softraid0 at root scsibus2 at softraid0: 256 targets pmon bootpath: /dev/disk/wd0 boot device: wd0 root on wd0a (78c08aaf23988299.a) swap on wd0b dump on wd0b umass1 at uhub0 port 2 configuration 1 interface 0 "JetFlash Mass Storage Device" rev 2.00/1.42 addr 4 umass1: using SCSI over Bulk-Only scsibus3 at umass1: 2 targets, initiator 0 sd1 at scsibus3 targ 1 lun 0: <JetFlash, Transcend 4GB, 8.07> SCSI2 0/direct removable sd1: 3911MB, 512 bytes/sector, 8011774 sectors sd1 detached scsibus3 detached umass1 detached ehci_idone: ex=0x98000000801693b0 is done! ehci_idone: ex=0x98000000801693b0 is done! ehci_idone: ex=0x98000000801693b0 is done! ehci_idone: ex=0x98000000801693b0 is done! ehci_idone: ex=0x98000000801693b0 is done! ehci_idone: ex=0x98000000801693b0 is done! ehci_idone: ex=0x98000000801693b0 is done! ehci_idone: ex=0x98000000801693b0 is done! ehci_idone: ex=0x98000000801693b0 is done! ehci_idone: ex=0x98000000801693b0 is done! ehci_idone: ex=0x98000000801693b0 is done!