Hello! Upgraded a soekris to 5.7-stable (built by flashrd) over the weekend and since then I'm seeing the following in the logs:
May 3 22:43:59 router /bsd: com4: 6 silo overflows, 0 ibuf overflows May 3 22:47:09 router /bsd: com4: 1 silo overflow, 0 ibuf overflows May 3 22:53:42 router /bsd: com4: 1 silo overflow, 0 ibuf overflows May 3 22:55:48 router /bsd: com4: 1 silo overflow, 0 ibuf overflows May 3 23:03:47 router last message repeated 2 times May 3 23:35:17 router /bsd: com4: 1 silo overflow, 0 ibuf overflows May 4 01:31:24 router /bsd: com4: 82 silo overflows, 0 ibuf overflows May 4 02:01:01 router /bsd: com4: 3 silo overflows, 0 ibuf overflows May 4 06:01:01 router /bsd: com4: 1 silo overflow, 0 ibuf overflows May 4 09:01:01 router /bsd: com4: 1 silo overflow, 0 ibuf overflows May 4 09:31:28 router /bsd: com4: 1 silo overflow, 0 ibuf overflows May 4 09:33:23 router /bsd: com4: 8 silo overflows, 0 ibuf overflows May 4 09:34:24 router /bsd: com4: 75 silo overflows, 0 ibuf overflows May 4 09:39:57 router /bsd: com4: 1 silo overflow, 0 ibuf overflows May 4 10:29:17 router /bsd: com4: 1 silo overflow, 0 ibuf overflows The GPS is attached by the following in /etc/ttys tty04 "/sbin/ldattach -s 9600 -t dcd nmea" unknown on softcar The GPS itself is an Adafruit Ultimate GPS Breakout (https://www.adafruit.com/products/746) with a small MAX232 circuit for level conversion and to connect PPS output to DCD pin on the serial port. ntpd still reports the sensor is valid. I haven't noticed it changing to any state other than OK in hw.sensors (this is another project: using the new skgpio device to light up the Soekris' red LED when the sensor state changes to something bad!) I never noticed anything wrong with it on 5.6, although perhaps there was always an issue and it's merely being logged now? I've included a dmesg below. Cheers, Mark OpenBSD 5.7-stable (FLASHRD.MP) #3: Sat May 2 18:29:26 AEST 2015 r...@black.home:/usr/src/sys/arch/amd64/compile/FLASHRD.MP real mem = 1056833536 (1007MB) avail mem = 1022943232 (975MB) mpath0 at root scsibus0 at mpath0: 256 targets mainbus0 at root bios0 at mainbus0 acpi at bios0 not configured mpbios0 at bios0: Intel MP Specification 1.4 cpu0 at mainbus0: apid 0 (boot processor) cpu0: Genuine Intel(R) CPU @ 1.00GHz, 1000.14 MHz cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,MOVBE,NXE,LONG,LAHF,PERF cpu0: 512KB 64b/line 8-way L2 cache cpu0: smt 0, core 0, package 0 mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges cpu0: apic clock running at 100MHz cpu0: mwait min=64, max=64, C-substates=0.2.2.0.2, IBE cpu1 at mainbus0: apid 1 (application processor) cpu1: Genuine Intel(R) CPU @ 1.00GHz, 1000.01 MHz cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,MOVBE,NXE,LONG,LAHF,PERF cpu1: 512KB 64b/line 8-way L2 cache cpu1: smt 1, core 0, package 0 mpbios0: bus 0 is type PCI mpbios0: bus 64 is type ISA ioapic0 at mainbus0: apid 0 pa 0xfec00000, version 20, 24 pins cpu0: unknown Enhanced SpeedStep CPU, msr 0x06090a0a06000a0d cpu0: using only highest, current and lowest power states cpu0: Enhanced SpeedStep 1000 MHz: speeds: 1000, 1000, 600 MHz pci0 at mainbus0 bus 0 pchb0 at pci0 dev 0 function 0 "Intel E600 Host" rev 0x05 pchb1 at pci0 dev 1 function 0 "Intel E600 Config" rev 0x00 ppb0 at pci0 dev 23 function 0 "Intel E600 PCIE" rev 0x00 pci1 at ppb0 bus 1 ppb1 at pci1 dev 0 function 0 "Intel EG20T PCIE" rev 0x01 pci2 at ppb1 bus 2 "Intel EG20T Packet Hub" rev 0x01 at pci2 dev 0 function 0 not configured "Intel EG20T Ethernet" rev 0x02 at pci2 dev 0 function 1 not configured "Intel EG20T GPIO" rev 0x01 at pci2 dev 0 function 2 not configured ohci0 at pci2 dev 2 function 0 "Intel EG20T USB" rev 0x02: apic 0 int 19, version 1.0 ohci1 at pci2 dev 2 function 1 "Intel EG20T USB" rev 0x02: apic 0 int 19, version 1.0 ohci2 at pci2 dev 2 function 2 "Intel EG20T USB" rev 0x02: apic 0 int 19, version 1.0 ehci0 at pci2 dev 2 function 3 "Intel EG20T USB" rev 0x02: apic 0 int 19 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1 "Intel EG20T USB Client" rev 0x02 at pci2 dev 2 function 4 not configured sdhc0 at pci2 dev 4 function 0 "Intel EG20T SDIO" rev 0x01: apic 0 int 18 sdmmc0 at sdhc0 sdhc1 at pci2 dev 4 function 1 "Intel EG20T SDIO" rev 0x01: apic 0 int 18 sdmmc1 at sdhc1 ahci0 at pci2 dev 6 function 0 "Intel EG20T AHCI" rev 0x02: msi, AHCI 1.1 scsibus1 at ahci0: 32 targets ohci3 at pci2 dev 8 function 0 "Intel EG20T USB" rev 0x02: apic 0 int 16, version 1.0 ohci4 at pci2 dev 8 function 1 "Intel EG20T USB" rev 0x02: apic 0 int 16, version 1.0 ohci5 at pci2 dev 8 function 2 "Intel EG20T USB" rev 0x02: apic 0 int 16, version 1.0 ehci1 at pci2 dev 8 function 3 "Intel EG20T USB" rev 0x02: apic 0 int 16 usb1 at ehci1: USB revision 2.0 uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1 "Intel EG20T DMA" rev 0x00 at pci2 dev 10 function 0 not configured puc0 at pci2 dev 10 function 1 "Intel EG20T Serial" rev 0x01: ports: 1 com com4 at puc0 port 0 apic 0 int 19: ti16750, 64 byte fifo com4: probed fifo depth: 0 bytes puc1 at pci2 dev 10 function 2 "Intel EG20T Serial" rev 0x00: ports: 1 com com5 at puc1 port 0 apic 0 int 19: ti16750, 64 byte fifo puc2 at pci2 dev 10 function 3 "Intel EG20T Serial" rev 0x00: ports: 1 com com6 at puc2 port 0 apic 0 int 19: ti16750, 64 byte fifo puc3 at pci2 dev 10 function 4 "Intel EG20T Serial" rev 0x00: ports: 1 com com7 at puc3 port 0 apic 0 int 19: ti16750, 64 byte fifo "Intel EG20T DMA" rev 0x00 at pci2 dev 12 function 0 not configured "Intel EG20T SPI" rev 0x00 at pci2 dev 12 function 1 not configured "Intel EG20T I2C" rev 0x00 at pci2 dev 12 function 2 not configured "Intel EG20T CAN" rev 0x00 at pci2 dev 12 function 3 not configured "Intel EG20T 1588" rev 0x01 at pci2 dev 12 function 4 not configured usb2 at ohci0: USB revision 1.0 uhub2 at usb2 "Intel OHCI root hub" rev 1.00/1.00 addr 1 usb3 at ohci1: USB revision 1.0 uhub3 at usb3 "Intel OHCI root hub" rev 1.00/1.00 addr 1 usb4 at ohci2: USB revision 1.0 uhub4 at usb4 "Intel OHCI root hub" rev 1.00/1.00 addr 1 usb5 at ohci3: USB revision 1.0 uhub5 at usb5 "Intel OHCI root hub" rev 1.00/1.00 addr 1 usb6 at ohci4: USB revision 1.0 uhub6 at usb6 "Intel OHCI root hub" rev 1.00/1.00 addr 1 usb7 at ohci5: USB revision 1.0 uhub7 at usb7 "Intel OHCI root hub" rev 1.00/1.00 addr 1 ppb2 at pci0 dev 24 function 0 "Intel E600 PCIE" rev 0x00 pci3 at ppb2 bus 3 ppb3 at pci3 dev 0 function 0 "IDT 89HPES4T4" rev 0x0e pci4 at ppb3 bus 4 ppb4 at pci4 dev 2 function 0 "IDT 89HPES4T4" rev 0x0e pci5 at ppb4 bus 5 em0 at pci5 dev 0 function 0 "Intel 82574L" rev 0x00: msi, address 00:00:24:d0:f1:74 ppb5 at pci4 dev 3 function 0 "IDT 89HPES4T4" rev 0x0e pci6 at ppb5 bus 6 em1 at pci6 dev 0 function 0 "Intel 82574L" rev 0x00: msi, address 00:00:24:d0:f1:75 ppb6 at pci4 dev 4 function 0 "IDT 89HPES4T4" rev 0x0e pci7 at ppb6 bus 7 ppb7 at pci0 dev 25 function 0 "Intel E600 PCIE" rev 0x00 pci8 at ppb7 bus 8 ppb8 at pci8 dev 0 function 0 "IDT 89HPES4T4" rev 0x0e pci9 at ppb8 bus 9 ppb9 at pci9 dev 2 function 0 "IDT 89HPES4T4" rev 0x0e pci10 at ppb9 bus 10 em2 at pci10 dev 0 function 0 "Intel 82574L" rev 0x00: msi, address 00:00:24:d0:f1:76 ppb10 at pci9 dev 3 function 0 "IDT 89HPES4T4" rev 0x0e pci11 at ppb10 bus 11 em3 at pci11 dev 0 function 0 "Intel 82574L" rev 0x00: msi, address 00:00:24:d0:f1:77 ppb11 at pci9 dev 4 function 0 "IDT 89HPES4T4" rev 0x0e pci12 at ppb11 bus 12 ppb12 at pci0 dev 26 function 0 "Intel E600 PCIE" rev 0x00 pci13 at ppb12 bus 13 tcpcib0 at pci0 dev 31 function 0 "Intel E600 LPC" rev 0x00: 14318179 Hz timer, watchdog isa0 at tcpcib0 com0 at isa0 port 0x3f8/8 irq 4: ti16750, 64 byte fifo com0: console pcppi0 at isa0 port 0x61 spkr0 at pcppi0 skgpio0 at isa0 port 0x680/32 gpio0 at skgpio0: 16 pins gpio1 at skgpio0: 2 pins umass0 at uhub1 port 3 configuration 1 interface 0 "SanDisk Cruzer Fit" rev 2.00/1.27 addr 2 umass0: using SCSI over Bulk-Only scsibus2 at umass0: 2 targets, initiator 0 sd0 at scsibus2 targ 1 lun 0: <SanDisk, Cruzer Fit, 1.27> SCSI4 0/direct removable serial.07815571710620110005 sd0: 7633MB, 512 bytes/sector, 15633408 sectors vscsi0 at root scsibus3 at vscsi0: 256 targets softraid0 at root scsibus4 at softraid0: 256 targets root on rd0a swap on rd0b dump on rd0b