Hello all,
I have an older i386 pc that I've been using as my home firewall for some
years now. It currently runs 3.3 and I was hoping to do an upgrade, so I
did go ahead and buy the full CD set (impressive packaging, btw) after
having trouble with boot floppies (marginal drive) and the boot CD ISO.
However, the kernel panics every time I try and boot the 3.8 CD. I've
also tried 3.7, 3.6 and 3.5 boot CDs that I downloaded from the OpenBSD
ftp server. Hardware seems fine; I ran memtest86+ for a day and it did
about 30 passes with no errors, I tried different CD-ROM drives, different
IDE cables, removed all network cards, etc., but still it panics in the
same place (right after "rd0: fixed, 3800 blocks"). CPU is an AMD
K6-2-500 clocked down to 300 - temperature is fine (about 110F), mainboard
is an old Epox.
On the suggestion of a bsdforums.org user, I tried downloading bsd.rd and
booting that from the 3.3 install, and that failed. I'm guessing it has
something to do with the exec format changing; perhaps the old loader
doesn't understand the new kernel exec format?
rebooting...
boot> /bsd.rd
booting hd0a:/bsd.rd: failed(79). will try /obsd
boot> ls bsd.rd
-rwxr-xr-x 0,0 4658297 hd0a:bsd.rd
boot> ls obsd
-rwxr-xr-x 0,0 2487309 hd0a:obsd
boot>
...snip...
gw# cd /
gw# file bsd.rd
bsd.rd: ELF 32-bit LSB executable, Intel 80386, version 1, statically
linked, not stripped
gw# file obsd
obsd: OpenBSD/i386 demand paged executable not stripped
gw#
I have this thing hooked up via serial now, so if someone can point me in
the right direction (how to get a dump when booting from CD, how to look
at that dump, etc.), I will gladly do so. I have also included the 3.3
dmesg below.
Thanks,
Charles
_____
Here is the partial boot message booting 3.8:
>> OpenBSD/i386 CDBOOT 1.04
boot>
booting cd0a:/3.8/i386/bsd.rd: 4369156+828044 [52+151072+137381]=0x53b600
entry point at 0x100120
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2005 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 3.8 (RAMDISK_CD) #794: Sat Sep 10 15:58:32 MDT 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: AMD-K6(tm) 3D processor ("AuthenticAMD" 586-class) 301 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX
real mem = 133799936 (130664K)
avail mem = 116502528 (113772K)
using 1658 buffers containing 6791168 bytes (6632K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(ee) BIOS, date 01/03/00, BIOS32 rev. 0 @
0xfb390
apm0 at bios0: Power Management spec V1.2
apm0: flags 70102 dobusy 1 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xb80c
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdde0/128 (6 entries)
pcibios0: PCI Exclusive IRQs: 5 10 11
pcibios0: PCI Interrupt Router at 000:07:0 ("VIA VT82C586 ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x2000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "VIA VT82C598 PCI" rev 0x04
ppb0 at pci0 dev 1 function 0 "VIA VT82C598 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Rage Pro" rev 0x5c
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
pcib0 at pci0 dev 7 function 0 "VIA VT82C586 ISA" rev 0x47
pciide0 at pci0 dev 7 function 1 "VIA VT82C571 IDE" rev 0x06: ATA33,
channel 0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <Maxtor 72004 AP>
wd0: 32-sector PIO, LBA, 1916MB, 3924360 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <SAMSUNG, CD-ROM SC-148F, F007> SCSI0
5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
uhci0 at pci0 dev 7 function 2 "VIA VT83C572 USB" rev 0x02: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
"VIA VT82C586 Power" rev 0x10 at pci0 dev 7 function 3 not configured
sis0 at pci0 dev 17 function 0 "NS DP83815 10/100" rev 0x00: DP83816A, irq
10, address 00:09:5b:22:4a:ee
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
xl0 at pci0 dev 18 function 0 "3Com 3c900 10Base-T" rev 0x00: irq 5,
address 00:a0:24:ce:11:02
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
biomask fbc5 netmask ffe5 ttymask ffe7
rd0: fixed, 3800 blocks
fatal page fault in supervisor mode
trap type 6 code 2 eip d02b9015 cs 50 eflags 10002 cr2 1ffec1c6 cpl a0
panic: trap type 6, code=2, pc=d02b9015
syncing disks... done
dumping to dev 1101, offset 0
dump error 19
rebooting...
_____
3.3 dmesg:
OpenBSD 3.3 (GW) #7: Mon Oct 6 03:32:16 EDT 2003
[EMAIL PROTECTED]:/sys/arch/i386/compile/GW
cpu0: AMD K6-2 ("AuthenticAMD" 586-class) 301 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX
real mem = 133804032 (130668K)
avail mem = 120475648 (117652K)
using 1658 buffers containing 6791168 bytes (6632K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(ee) BIOS, date 01/03/00, BIOS32 rev. 0 @
0xfb390
pcibios0 at bios0: rev. 2.1 @ 0xf0000/0xb80c
pcibios0: PCI IRQ Routing Table rev. 1.0 @ 0xfdde0/128 (6 entries)
pcibios0: PCI Exclusive IRQs: 5 10 11
pcibios0: PCI Interrupt Router at 000:07:0 ("VIA VT82C586 PCI-ISA" rev
0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x2000!
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "VIA VT82C598 Host-PCI" rev 0x04
ppb0 at pci0 dev 1 function 0 "VIA VT82C598 PCI-AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Rage Pro" rev 0x5c
wsdisplay0 at vga1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 7 function 0 "VIA VT82C586 PCI-ISA" rev 0x47
pciide0 at pci0 dev 7 function 1 "VIA VT82C571 IDE" rev 0x06: ATA33,
channel 0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <Maxtor 72004 AP>
wd0: 32-sector PIO, LBA, 1916MB, 3893 cyl, 16 head, 63 sec, 3924360
sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <SAMSUNG, CD-ROM SC-148F, F007> SCSI0
5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
uhci0 at pci0 dev 7 function 2 "VIA VT83C572 USB" rev 0x02: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x0000 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pchb1 at pci0 dev 7 function 3 "VIA VT82C586 Power Mgmt" rev 0x10
sis0 at pci0 dev 17 function 0 "NS DP83815 10/100" rev 0x00: irq 10
address 00:09:5b:22:4a:ee
ukphy0 at sis0 phy 0: Generic IEEE 802.3u media interface
ukphy0: OUI 0x080017, model 0x0002, rev. 1
xl0 at pci0 dev 18 function 0 "3Com 3c900 10Base-T" rev 0x00: irq 5
address 00:a0:24:ce:11:02
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
biomask c840 netmask cc60 ttymask cc62
pctr: user-level cycle counter enabled
mtrr: K6-family MTRR support (2 registers)
Kernelized RAIDframe activated
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
uhub1 at uhub0 port 2
uhub1: vendor 0x0451 product 0x2046, class 9/0, rev 1.10/1.25, addr 2
uhub1: 4 ports with 4 removable, self powered
uhidev0 at uhub1 port 1 configuration 1 interface 0
uhidev0: ATEN 2 Port USB KVM B V1.60, rev 1.10/1.00, addr 3, iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub1 port 1 configuration 1 interface 1
uhidev1: ATEN 2 Port USB KVM B V1.60, rev 1.10/1.00, addr 3, iclass 3/1
ums0 at uhidev1: 5 buttons and Z dir.
wsmouse0 at ums0 mux 0
