Iâve been running OpenBSD on an old HP MediaSmart 470 box. I just installed 5.9 yesterday. The BIOS reports 3 installed drives:
IDE Channel 2 Master : ST31500541AS CC34 (OpenBSD disklabel) IDE Channel 2 Slave : WDC WD20EFRX-68EUZN0 82.00A82 (new, unformatted) IDE Channel 3 Master : ST3500630AS 3.CHN (OpenBSD disklabel) IDE Channel 3 Slave : None These are all SATA drives that report LBA, ATA. (The Serial ATA controller mode is set to â4P(IDE)+4S(IDE)â in the BIOS.) The boot sequence shows: disk: hd0+ hd1+* hd2 hd3* System works fine with the 2 drives it recognizes. The Channel 2 and Channel 3 âMasterâ drives. The âSlaveâ drive is not recognized. Also, not sure I understand the âdisk:â line above. The missing âSlaveâ drives are nothing new. I had the same problem with prior versions of OpenBSD. Iâd never spent much time on the problem since the two drives still gave me a perfectly functional system. Iâve now spent some time on it and I canât find a way to get more than 2 drives recognized. Am I missing something basic? Or do the vintage (c. 2008) hardware and drivers prevent this? dmesg below: OpenBSD 5.9 (GENERIC) #1761: Fri Feb 26 01:15:04 MST 2016 dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC real mem = 2097086464 (1999MB) avail mem = 2029428736 (1935MB) mpath0 at root scsibus0 at mpath0: 256 targets mainbus0 at root bios0 at mainbus0: SMBIOS rev. 2.2 @ 0xf0000 (29 entries) bios0: vendor Phoenix Technologies, LTD version "R02" date 07/13/2007 bios0: HP MediaSmart Server acpi0 at bios0: rev 0 acpi0: sleep states S0 S3 S4 S5 acpi0: tables DSDT FACP BOOT SSDT MCFG APIC acpi0: wakeup devices USB0(S5) USB1(S5) USB2(S5) USB3(S5) MAC0(S5) AMR0(S4) HDA0(S5) PS2M(S5) PS2K(S4) PCI0(S5) acpitimer0 at acpi0: 3579545 Hz, 24 bits acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255 acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat cpu0 at mainbus0: apid 0 (boot processor) cpu0: AMD Sempron(tm) Processor 3400+, 6840.53 MHz cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS H,MMX,FXSR,SSE,SSE2,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW,LAHF,EAPICSP,A MCR8 cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 256KB 64b/line 16-way L2 cache cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative mtrr: Pentium Pro MTRR support, 8 var ranges, 88 fixed ranges cpu0: apic clock running at 200MHz ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 14, 24 pins ioapic0: misconfigured as apic 2, remapped to apid 1 acpiprt0 at acpi0: bus 0 (PCI0) acpicpu0 at acpi0: C1(@1 halt!), PSS acpitz0 at acpi0: critical temperature is 100 degC acpibtn0 at acpi0: PWRB cpu0: PowerNow! K8 6840 MHz: speeds: 1800 1000 MHz pci0 at mainbus0 bus 0 pchb0 at pci0 dev 0 function 0 "SiS 761 PCI" rev 0x02 agp at pchb0 not configured ppb0 at pci0 dev 1 function 0 "SiS 86C202 AGP" rev 0x00 pci1 at ppb0 bus 1 vga1 at pci1 dev 0 function 0 "SiS 6330 VGA" rev 0x03 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) pcib0 at pci0 dev 2 function 0 "SiS 966 ISA" rev 0x59 ohci0 at pci0 dev 3 function 0 "SiS 5597/5598 USB" rev 0x0f: apic 1 int 20, version 1.0, legacy support ohci1 at pci0 dev 3 function 1 "SiS 5597/5598 USB" rev 0x0f: apic 1 int 21, version 1.0, legacy support ehci0 at pci0 dev 3 function 3 "SiS 7002 USB" rev 0x00: apic 1 int 23 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 "SiS EHCI root hub" rev 2.00/1.00 addr 1 se0 at pci0 dev 4 function 0 "SiS 191" rev 0x01: apic 1 int 19, address 00:0a:e4:87:96:73 atphy0 at se0 phy 0: F1 10/100/1000 PHY, rev. 6 pciide0 at pci0 dev 5 function 0 "SiS 1183 SATA" rev 0x02: DMA pciide0: using apic 1 int 17 for native-PCI interrupt wd0 at pciide0 channel 0 drive 0: <ST31500541AS> wd0: 16-sector PIO, LBA48, 1430799MB, 2930277168 sectors wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 6 wd1 at pciide0 channel 1 drive 0: <ST3500630AS> wd1: 16-sector PIO, LBA48, 476940MB, 976773168 sectors wd1(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 5 pchb1 at pci0 dev 24 function 0 "AMD AMD64 0Fh HyperTransport" rev 0x00 pchb2 at pci0 dev 24 function 1 "AMD AMD64 0Fh Address Map" rev 0x00 pchb3 at pci0 dev 24 function 2 "AMD AMD64 0Fh DRAM Cfg" rev 0x00 kate0 at pci0 dev 24 function 3 "AMD AMD64 0Fh Misc Cfg" rev 0x00: core rev DH-F2 ppb1 at pci0 dev 31 function 0 "SiS PCI-PCI" rev 0x00: apic 1 int 16 pci2 at ppb1 bus 2 pciide1 at pci2 dev 0 function 0 "Marvell 88SE6121 SATA" rev 0xb2: DMA (unsupported), channel 0 configured to native-PCI, channel 1 configured to native-PCI pciide1: using apic 1 int 16 for native-PCI interrupt pciide1: channel 0 ignored (not responding; disabled or no drives?) pciide1: channel 1 ignored (not responding; disabled or no drives?) isa0 at pcib0 isadma0 at isa0 pckbc0 at isa0 port 0x60/5 irq 1 irq 12 pckbd0 at pckbc0 (kbd slot) wskbd0 at pckbd0: console keyboard, using wsdisplay0 pcppi0 at isa0 port 0x61 spkr0 at pcppi0 it0 at isa0 port 0x2e/2: IT8705F rev 3, EC port 0x290 usb1 at ohci0: USB revision 1.0 uhub1 at usb1 "SiS OHCI root hub" rev 1.00/1.00 addr 1 usb2 at ohci1: USB revision 1.0 uhub2 at usb2 "SiS OHCI root hub" rev 1.00/1.00 addr 1 umass0 at uhub0 port 2 configuration 1 interface 0 "SMI Corporation USB DISK" rev 2.00/11.00 addr 2 umass0: using SCSI over Bulk-Only scsibus1 at umass0: 2 targets, initiator 0 sd0 at scsibus1 targ 1 lun 0: <SMI, USB DISK, 1100> SCSI0 0/direct fixed serial.090c1000012700054912 sd0: 247MB, 512 bytes/sector, 506880 sectors uhidev0 at uhub1 port 3 configuration 1 interface 0 "SEM USB Keyboard" rev 1.10/1.10 addr 2 uhidev0: iclass 3/1 ukbd0 at uhidev0: 8 variable keys, 6 key codes wskbd1 at ukbd0 mux 1 wskbd1: connecting to wsdisplay0 uhidev1 at uhub1 port 3 configuration 1 interface 1 "SEM USB Keyboard" rev 1.10/1.10 addr 2 uhidev1: iclass 3/0, 2 report ids uhid0 at uhidev1 reportid 1: input=2, output=0, feature=0 uhid1 at uhidev1 reportid 2: input=1, output=0, feature=0 vscsi0 at root scsibus2 at vscsi0: 256 targets softraid0 at root scsibus3 at softraid0: 256 targets root on wd0a (8c0356d01e55113f.a) swap on wd0b dump on wd0b hw.sensors.acpitz0.temp0=37.00 degC (zone temperature) hw.sensors.kate0.temp0=44.00 degC hw.sensors.kate0.temp2=44.00 degC hw.sensors.it0.temp0=57.00 degC hw.sensors.it0.temp1=40.00 degC hw.sensors.it0.temp2=118.00 degC hw.sensors.it0.fan0=1638 RPM hw.sensors.it0.fan1=1687 RPM hw.sensors.it0.volt0=1.25 VDC (VCORE_A) hw.sensors.it0.volt1=1.82 VDC (VCORE_B) hw.sensors.it0.volt2=3.31 VDC (+3.3V) hw.sensors.it0.volt3=4.92 VDC (+5V) hw.sensors.it0.volt4=11.78 VDC (+12V) hw.sensors.it0.volt5=-6.86 VDC (-12V) hw.sensors.it0.volt6=-2.65 VDC (-5V) hw.sensors.it0.volt7=5.05 VDC (+5VSB) hw.sensors.it0.volt8=3.12 VDC (VBAT) [demime 1.01d removed an attachment of type application/pkcs7-signature which had a name of smime.p7s]