Hi List, Hetzner has like other dedicated hosting providers an "crazy" looking network setup for ipv4. Here point to point for the default gw in a different network segment.
So it's important also to keep that in mind. Maybe this document helps a bit, need to adapt to Openbsd. https://wiki.hetzner.de/index.php/KVM_mit_Nutzung_aller_IPs_aus_Subnetz/en Cheers Karsten Am 20.07.2017 6:29 vorm. schrieb "Mike Larkin" <mlar...@azathoth.net>: On Thu, Jul 20, 2017 at 04:23:40AM +0200, Leo Unglaub wrote: > Hey friends, > i am trying out vmd and I have a little problem getting networking going > inside the guest machine. I am not sure if this is a problem in vmd or > simply my misconfiguration. > > From my datacenter i got the following data: > > Main Server (OpenBSD GENERIC.MP#99 amd64) > ######################################### > IP: 144.76.102.204 > Netmask: 255.255.255.224 > Gateway: 144.76.102.193 > > > Virtual Machine (OpenBSD GENERIC.MP#99 amd64) > ############################################# > I got an entire subnet from the datacenter. 136.243.186.160/29 So i decided > to use the following IP in it. > > IP: 136.243.186.161 > Netmask: 255.255.255.248 > Gateway: 144.76.102.204 > > > According to there documentation they always route all subnets on the main > IP. In my case 144.76.102.204. > > > On my host I configured the em0 interface according to the datacenter data > and it works fine. The host who runs vmd is connected correctly. In my > /etc/vm.conf i created a switch called "uplink" and added em0 to it. When i > check the current config via ifconfig i get the following. > > > em0: flags=8b43<UP,BROADCAST,RUNNING,PROMISC,ALLMULTI,SIMPLEX,MULTICAST> mtu 1500 > > lladdr 90:1b:0e:8b:0f:34 > > description: hetzner-uplink > > index 1 priority 0 llprio 3 > > groups: egress > > media: Ethernet autoselect (1000baseT full-duplex,rxpause,txpause) > > status: active > > inet 144.76.102.204 netmask 0xffffffe0 broadcast 144.76.102.223 > > > > > > tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 > > lladdr fe:e1:ba:d0:7e:0a > > description: vm1-if0-foobar > > index 5 priority 0 llprio 3 > > groups: tap > > status: active > > > > bridge0: flags=41<UP,RUNNING> > > description: switch1-uplink > > index 7 llprio 3 > > groups: bridge > > priority 32768 hellotime 2 fwddelay 15 maxage 20 holdcnt 6 proto rstp > > em0 flags=3<LEARNING,DISCOVER> > > port 1 ifpriority 0 ifcost 0 > > tap0 flags=3<LEARNING,DISCOVER> > > port 5 ifpriority 0 ifcost 0 > > Addresses (max cache: 100, timeout: 240): > > 0c:86:10:ed:35:58 em0 1 flags=0<> > > My /etc/vm.conf looks like this: > > > switch "uplink" { > > add em0 > > } > > > > vm "foobar" { > > memory 2G > > disk "/tmp/1.vdi" > > interface { > > switch "uplink" > > } > > } > > When i start the vm with my current /bsd.rd i start the installer and insert > the following: > > > Available network interfaces are: vio0 vlan0. > > Which network interface do you wish to configure? (or 'done') [vio0] > > IPv4 address for vio0? (or 'dhcp' or 'none') [dhcp] 136.243.186.161 > > Netmask for vio0? [255.255.255.248] IPv6 address for vio0? (or > > 'autoconf' or 'none') [none] Available network interfaces are: vio0 > > vlan0. > > Which network interface do you wish to configure? (or 'done') [done] > > Default IPv4 route? (IPv4 address or none) 144.76.102.204 > > add net default: gateway 144.76.102.204: Network is unreachable > > Can you people see something that i might missed? > Big thanks in advance and greetings > Leo > > sysctl net.inet.ip.forwarding=1 ? I'm not a networking expert but I think your VM's subnet mask is wrong for the gateway you are trying to use. -ml
