Hi All,
dmesg of a nanoPi A64:
http://www.friendlyarm.com/index.php?route=product/product&path=69&product_id=159
Absolutely no issues with the openBSD installer. My serial break out
cables seem to be backwards so at first I wasn't seeing anything on the
console. After I swapped receive/transmit, everything was fine.
I did connect the board to a HDMI monitor and briefly saw the boot
process, but soon after, the monitor went blank.
$ dmesg
OpenBSD 6.3-current (GENERIC.MP) #86: Wed Apr 25 02:38:55 MDT 2018
dera...@arm64.openbsd.org:/usr/src/sys/arch/arm64/compile/GENERIC.MP
real mem = 947683328 (903MB)
avail mem = 888680448 (847MB)
mainbus0 at root: Pine64+
cpu0 at mainbus0 mpidr 0: ARM Cortex-A53 r0p4
efi0 at mainbus0: UEFI 2.7
efi0: Das U-Boot rev 0x0
psci0 at mainbus0: PSCI 0.2
agtimer0 at mainbus0: tick rate 24000 KHz
simplebus0 at mainbus0: "soc"
sxiccmu0 at simplebus0
sxipio0 at simplebus0: 103 pins
ampintc0 at simplebus0 nirq 224, ncpu 4 ipi: 0, 1: "interrupt-controller"
sxiccmu1 at simplebus0
sxipio1 at simplebus0: 13 pins
sximmc0 at simplebus0
sdmmc0 at sximmc0: 4-bit, sd high-speed, mmc high-speed, dma
ehci0 at simplebus0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Generic EHCI root hub" rev
2.00/1.00 addr 1
com0 at simplebus0: ns16550, no working fifo
com0: console
sxitwi0 at simplebus0
iic0 at sxitwi0
sxirtc0 at simplebus0
dwxe0 at simplebus0: address ff:ff:ff:ff:ff:ff
rgephy0 at dwxe0 phy 0: RTL8169S/8110S/8211 PHY, rev. 5
rgephy1 at dwxe0 phy 7: RTL8169S/8110S/8211 PHY, rev. 5
gpio0 at sxipio0: 32 pins
gpio1 at sxipio0: 32 pins
gpio2 at sxipio0: 32 pins
gpio3 at sxipio0: 32 pins
gpio4 at sxipio0: 32 pins
gpio5 at sxipio0: 32 pins
gpio6 at sxipio0: 32 pins
gpio7 at sxipio0: 32 pins
gpio8 at sxipio1: 32 pins
simplefb0 at mainbus0: 1920x1080
wsdisplay0 at simplefb0 mux 1
wsdisplay0: screen 0-5 added (std, vt100 emulation)
cpu1 at mainbus0 mpidr 1: ARM Cortex-A53 r0p4
cpu2 at mainbus0 mpidr 2: ARM Cortex-A53 r0p4
cpu3 at mainbus0 mpidr 3: ARM Cortex-A53 r0p4
scsibus0 at sdmmc0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <SD/MMC, SL32G, 0080> SCSI2 0/direct removable
sd0: 30436MB, 512 bytes/sector, 62333952 sectors
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
bootfile: sd0a:/bsd
boot device: sd0
root on sd0a (8f2cc65f9ef32a85.a) swap on sd0b dump on sd0b
Thanks!
