Am Mi., 8. Apr. 2020 um 08:37 Uhr schrieb Otto Moerbeek <o...@drijf.net>:
>
> On Wed, Apr 08, 2020 at 01:11:29AM +0200, Sigi Rudzio wrote:
>
> > Hello misc@,
> >
> > while testing the FFS2 patches by otto@ I noticed that I was unable
> > to install -current on my silver Blade 2500.
> >
> > tar fails while unpacking the sets, although the files are ok, if I rename
> > base67.tgz to base66.tgz to fool the 6.6 installer I can install 6.7-beta,
> > although it fails/panics with a lot of "Illegal instruction" errors on the
> > first boot.
> >
> > otto@ already told me that this might be fallout from the recent clang
> > changes.
>
> Well, I sais it *could be*, but you did not show my the actual errors
> in that email.  The errorsbelow indicate a harware issue, i.e. bad
> disk.
>
>         -Otto

Sorry, I should have been clearer.

I tried another disk from my working V240 and got the same errors.

Installing on an IDE hard disk works and the system is working fine,
even writing large files to the SCSI disk is fine, but I can make it panic
with tar.
So I guess this is some kind of SCSI bus hardware issue that 6.6 doesn't
trigger and some change between 6.6 and 6.7-beta does trigger it.

Sorry for the noise and thanks for the help!

Regards

S. Rudzio

>
> >
> > 6.6 works fine.
> >
> > The failures are a bit random, it doesn't panic every time, sometimes
> > while installing 6.7-beta tar fails and I get to try again a few times 
> > before
> > I give up/it panics.
> >
> > I hope this information helps.
> >
> > Regards,
> >
> > S. Rudzio
> >
> > output from
> > -6.7-beta bsd.rd failing
> > -6.6 bsd.rd
> > -6.6 bsd.mp
> > -6.7-beta bsd.mp failing/panicing (installed with 6.6 bsd.rd)
> > following:
> >
> > latest bsd.rd (the previous two snapshots also failed, but I didn't save any
> > logs):
> > Booting /pci@1c,600000/network@3/bsd.rd
> > 4671584@0x1000000+6048@0x1474860+3248464@0x1c00000+945840@0x1f19150
> > symbols @ 0xfec68440 175+356136+219433 start=0x1000000
> > console is /pci@1e,600000/isa@7/serial@0,3f8
> > Copyright (c) 1982, 1986, 1989, 1991, 1993
> >         The Regents of the University of California.  All rights
> > reserved.
> > Copyright (c) 1995-2020 OpenBSD. All rights reserved.
> > https://www.OpenBSD.org
> >
> > OpenBSD 6.7-beta (RAMDISK) #259: Mon Apr  6 19:13:12 MDT 2020
> >     dera...@sparc64.openbsd.org:/usr/src/sys/arch/sparc64/compile/RAMDISK
> > real mem = 2147483648 (2048MB)
> > avail mem = 2098044928 (2000MB)
> > mainbus0 at root: Sun Blade 2500 (Silver)
> > "SUNW,UltraSPARC-IIIi" at mainbus0 not configured
> > cpu0 at mainbus0: SUNW,UltraSPARC-IIIi (rev 3.4) @ 1600 MHz
> > cpu0: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K
> > external (64 b/l)
> > "memory-controller" at mainbus0 not configured
> > "memory-controller" at mainbus0 not configured
> > schizo0 at mainbus0: "Tomatillo", version 4, ign 700, bus A 0 to 0
> > schizo0: dvma map c0000000-dfffffff
> > pci0 at schizo0
> > bge0 at pci0 dev 3 function 0 "Broadcom BCM5703" rev 0x00,
> > BCM5702/5703 A2 (0x1002)bge0: nvram lock timed out
> > : ivec 0x71c, address 00:03:ba:f2:ee:53
> > brgphy0 at bge0 phy 1: BCM5703 10/100/1000baseT PHY, rev. 2
> > "ppm" at mainbus0 not configured
> > schizo1 at mainbus0: "Tomatillo", version 4, ign 740, bus B 0 to 0
> > schizo1: dvma map c0000000-dfffffff
> > pci1 at schizo1
> > mpi0 at pci1 dev 4 function 0 "Symbios Logic 53c1030" rev 0x07: ivec
> > 0x769
> > mpi0: 0, firmware 1.3.11.1
> > scsibus0 at mpi0: 16 targets, initiator 7
> > sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST314670LSUN146G, 045A>
> > serial.SEAGATE_ST314670LSUN146G4442RJNV_3KS2RJNV
> > sd0: 140009MB, 512 bytes/sector, 286739329 sectors
> > mpi0: target 0 Sync at 160MHz width 16bit offset 63 QAS 1 DT 1 IU 1
> > mpi1 at pci1 dev 4 function 1 "Symbios Logic 53c1030" rev 0x07: ivec
> > 0x768
> > mpi1: 0, firmware 1.3.11.1
> > scsibus1 at mpi1: 16 targets, initiator 7
> > schizo2 at mainbus0: "Tomatillo", version 4, ign 780, bus A 0 to 1
> > schizo2: dvma map c0000000-dfffffff
> > pci2 at schizo2
> > ebus0 at pci2 dev 7 function 0 "Acer Labs M1533 ISA" rev 0x00
> > "flashprom" at ebus0 addr 0-fffff not configured
> > rtc0 at ebus0 addr 70-71: m5823
> > "i2c" at ebus0 addr 320-321 ivec 0x2e not configured
> > "power" at ebus0 addr 800-82f ivec 0x20 not configured
> > com0 at ebus0 addr 3f8-3ff ivec 0x2c: ns16550a, 16 byte fifo
> > com0: console
> > com1 at ebus0 addr 2e8-2ef ivec 0x2c: ns16550a, 16 byte fifo
> > "dma" at ebus0 addr 0-ffff not configured
> > "Acer Labs M7101 Power" rev 0x00 at pci2 dev 6 function 0 not
> > configured
> > "Acer Labs M5451 Audio" rev 0x02 at pci2 dev 8 function 0 not
> > configured
> > ohci0 at pci2 dev 10 function 0 "Acer Labs M5237 USB" rev 0x03: ivec
> > 0x7a7, version 1.0, legacy support
> > ohci1 at pci2 dev 11 function 0 "Acer Labs M5237 USB" rev 0x03: ivec
> > 0x7a6, version 1.0, legacy support
> > pciide0 at pci2 dev 13 function 0 "Acer Labs M5229 UDMA IDE" rev 0xc4:
> > DMA, channel 0 configured to native-PCI, channel 1 configured to
> > native-PCI
> > pciide0: using ivec 0x798 for native-PCI interrupt
> > pciide0: channel 0 disabled (no drives)
> > atapiscsi0 at pciide0 channel 1 drive 0
> > scsibus2 at atapiscsi0: 2 targets
> > cd0 at scsibus2 targ 0 lun 0: <TSSTcorp, CDW/DVD TS-H492C, SI00>
> > removable
> > cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
> > radeonfb0 at pci2 dev 2 function 0 "ATI Radeon VE" rev 0x00
> > radeonfb0: SUNW,375-3181, 1152x900
> > wsdisplay0 at radeonfb0
> > wsdisplay0: screen 0 added (std, sun emulation)
> > ppb0 at pci2 dev 4 function 0 "TI PCI2250" rev 0x02
> > pci3 at ppb0 bus 1
> > ohci2 at pci3 dev 8 function 0 "NEC USB" rev 0x43: ivec 0x794, version
> > 1.0
> > ohci3 at pci3 dev 8 function 1 "NEC USB" rev 0x43: ivec 0x795, version
> > 1.0
> > ehci0 at pci3 dev 8 function 2 "NEC USB" rev 0x04: ivec 0x796
> > usb0 at ehci0: USB revision 2.0
> > uhub0 at usb0 configuration 1 interface 0 "NEC EHCI root hub" rev
> > 2.00/1.00 addr 1
> > "TI TSB43AB23 FireWire" rev 0x00 at pci3 dev 11 function 0 not configured
> > usb1 at ohci2: USB revision 1.0
> > uhub1 at usb1 configuration 1 interface 0 "NEC OHCI root hub" rev
> > 1.00/1.00 addr 1
> > usb2 at ohci3: USB revision 1.0
> > uhub2 at usb2 configuration 1 interface 0 "NEC OHCI root hub" rev
> > 1.00/1.00 addr 1
> > usb3 at ohci0: USB revision 1.0
> > uhub3 at usb3 configuration 1 interface 0 "Acer Labs OHCI root hub"
> > rev 1.00/1.00 addr 1
> > usb4 at ohci1: USB revision 1.0
> > uhub4 at usb4 configuration 1 interface 0 "Acer Labs OHCI root hub"
> > rev 1.00/1.00 addr 1
> > "ppm" at mainbus0 not configured
> > schizo3 at mainbus0: "Tomatillo", version 4, ign 7c0, bus B 0 to 0
> > schizo3: dvma map c0000000-dfffffff
> > pci4 at schizo3
> > "i2c" at mainbus0 not configured
> > softraid0 at root
> > scsibus3 at softraid0: 256 targets
> > bootpath: /pci@1c,600000/network@3,0
> > root on rd0a swap on rd0b dump on rd0b
> > erase ^?, werase ^W, kill ^U, intr ^C, status ^T
> >
> > Welcome to the OpenBSD/sparc64 6.7 installation program.
> > Starting non-interactive mode in 5 seconds...
> > (I)nstall, (U)pgrade, (A)utoinstall or (S)hell? i
> > At any prompt except password prompts you can escape to a shell by
> > typing '!'. Default answers are shown in []'s and are selected by
> > pressing RETURN.  You can exit this program at any time by pressing
> > Control-C, but this can leave your system in an inconsistent state.
> >
> > Terminal type? [sun] xterm
> > System hostname? (short form, e.g. 'foo') XXX
> >
> > Available network interfaces are: bge0 vlan0.
> > Which network interface do you wish to configure? (or 'done') [bge0]
> > IPv4 address for bge0? (or 'dhcp' or 'none') [dhcp]
> > bge0: 192.168.2.131 lease accepted from 192.168.2.1
> > (fe:e1:ba:d2:bf:d6)
> > IPv6 address for bge0? (or 'autoconf' or 'none') [none] autoconf
> > Available network interfaces are: bge0 vlan0.
> > Which network interface do you wish to configure? (or 'done') [done]
> > Using DNS domainname XXX
> > Using DNS nameservers at 192.168.3.1
> >
> > Password for root account? (will not echo)
> > Password for root account? (again)
> > Start sshd(8) by default? [yes]
> > Do you want the X Window System to be started by xenodm(1)? [no]
> > Setup a user? (enter a lower-case loginname, or 'no') [no]
> > Since no user was setup, root logins via sshd(8) might be useful.
> > WARNING: root is targeted by password guessing attacks, pubkeys are
> > safer.
> > Allow root ssh login? (yes, no, prohibit-password) [no]
> > What timezone are you in? ('?' for list) [XXX]
> >
> > Available disks are: sd0.
> > Which disk is the root disk? ('?' for details) [sd0]
> > The auto-allocated layout for sd0 is:
> > #                size           offset  fstype [fsize bsize   cpg]
> >   a:             1.0G                0  4.2BSD   2048 16384     1 # /
> >   b:             2.3G          2116608    swap
> >   c:           136.7G                0  unused
> >   d:             4.0G          6838272  4.2BSD   2048 16384     1 #
> > /tmp
> >   e:             8.0G         15243648  4.2BSD   2048 16384     1 #
> > /var
> >   f:             6.0G         32034048  4.2BSD   2048 16384     1 #
> > /usr
> >   g:             1.0G         44631936  4.2BSD   2048 16384     1 #
> > /usr/X11R6
> >   h:            19.9G         46748544  4.2BSD   2048 16384     1 #
> > /usr/local
> >   i:             2.0G         88551552  4.2BSD   2048 16384     1 #
> > /usr/src
> >   j:             6.0G         92764416  4.2BSD   2048 16384     1 #
> > /usr/obj
> >   k:            86.5G        105362304  4.2BSD   2048 16384     1 #
> > /home
> > Use (A)uto layout, (E)dit auto layout, or create (C)ustom layout? [a]
> > /dev/rsd0a: 1033.5MB in 2116608 sectors of 512 bytes
> > 6 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > /dev/rsd0k: 88563.0MB in 181377024 sectors of 512 bytes
> > 438 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > /dev/rsd0d: 4104.2MB in 8405376 sectors of 512 bytes
> > 21 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > /dev/rsd0f: 6151.3MB in 12597888 sectors of 512 bytes
> > 31 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > /dev/rsd0g: 1033.5MB in 2116608 sectors of 512 bytes
> > 6 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > /dev/rsd0h: 20411.6MB in 41803008 sectors of 512 bytes
> > 101 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > /dev/rsd0j: 6151.3MB in 12597888 sectors of 512 bytes
> > 31 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > /dev/rsd0i: 2057.1MB in 4212864 sectors of 512 bytes
> > 11 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > /dev/rsd0e: 8198.4MB in 16790400 sectors of 512 bytes
> > 41 cylinder groups of 202.50MB, 12960 blocks, 25920 inodes each
> > /dev/sd0a (a8bb856211488659.a) on /mnt type ffs (rw, asynchronous, local)
> > /dev/sd0k (a8bb856211488659.k) on /mnt/home type ffs (rw,
> > asynchronous, local, nodev, nosuid)
> > /dev/sd0d (a8bb856211488659.d) on /mnt/tmp type ffs (rw, asynchronous,
> > local, nodev, nosuid)
> > /dev/sd0f (a8bb856211488659.f) on /mnt/usr type ffs (rw, asynchronous,
> > local, nodev)
> > /dev/sd0g (a8bb856211488659.g) on /mnt/usr/X11R6 type ffs (rw,
> > asynchronous, local, nodev)
> > /dev/sd0h (a8bb856211488659.h) on /mnt/usr/local type ffs (rw,
> > asynchronous, local, nodev)
> > /dev/sd0j (a8bb856211488659.j) on /mnt/usr/obj type ffs (rw,
> > asynchronous, local, nodev, nosuid)
> > /dev/sd0i (a8bb856211488659.i) on /mnt/usr/src type ffs (rw,
> > asynchronous, local, nodev, nosuid)
> > /dev/sd0e (a8bb856211488659.e) on /mnt/var type ffs (rw, asynchronous,
> > local, nodev, nosuid)
> >
> > Let's install the sets!
> > Location of sets? (cd0 disk http or 'done') [http]
> > HTTP proxy URL? (e.g. 'http://proxy:8080', or 'none') [none]
> > HTTP Server? (hostname, list#, 'done' or '?') [ftp.rudzio.net]
> > Server directory? [pub/OpenBSD/snapshots/sparc64]
> >
> > Select sets by entering a set name, a file name pattern or 'all'. De-select
> > sets by prepending a '-', e.g.: '-game*'. Selected sets are labelled '[X]'.
> >     [X] bsd           [X] base67.tgz    [X] game67.tgz    [X] xfont67.tgz
> >     [X] bsd.mp        [X] comp67.tgz    [X] xbase67.tgz   [X] xserv67.tgz
> >     [X] bsd.rd        [X] man67.tgz     [X] xshare67.tgz
> > Set name(s)? (or 'abort' or 'done') [done]
> > Get/Verify SHA256.sig   100% |**************************|  1885       00:00
> > Signature Verified
> > Get/Verify bsd          100% |**************************| 12483 KB    00:01
> > Get/Verify bsd.mp       100% |**************************| 12541 KB    00:01
> > Get/Verify bsd.rd       100% |**************************|  8560 KB    00:00
> > Get/Verify base67.tgz   100% |**************************|   169 MB    00:15
> > Get/Verify comp67.tgz   100% |**************************| 71992 KB    00:06
> > Get/Verify man67.tgz    100% |**************************|  7455 KB    00:00
> > Get/Verify game67.tgz   100% |**************************|  2866 KB    00:00
> > Get/Verify xbase67.tgz  100% |**************************| 18753 KB    00:01
> > Get/Verify xshare67.tgz 100% |**************************|  4500 KB    00:00
> > Get/Verify xfont67.tgz  100% |**************************| 39345 KB    00:03
> > Get/Verify xserv67.tgz  100% |**************************| 12537 KB    00:01
> > Installing bsd          100% |**************************| 12483 KB    00:00
> > Installing bsd.mp       100% |**************************| 12541 KB    00:00
> > Installing bsd.rd       100% |**************************|  8560 KB    00:00
> > Installing base67.tgz    66% |*****************         |   113 MB
> > 00:17 ETAftp: Reading from file: Input/output error
> > gzip: stdin: Input/output error
> > tar: End of archive volume 1 reached
> > /mnt/usr: bad dir ino 622362 at offset 0: mangled entry
> > panic: bad dir
> > syncing disks...95 95 54  done
> > Frame pointer is at 0x4002f23c8e1
> > Call traceback:
> > 12fdec4(1fab000, 80206910, 4002f23d190, 0, 12cacbc, 1f1d000,
> > 4002f23c9b1) fp = 4002f23c9b1
> > 110cbf4(100, 1c01000, 1, 100, 1, 0, 4002f23ca61) fp = 4002f23ca61
> > 1117ab8(100, 1f1d000, 1, 4002f23d458, 1f1e295, ffffffffffffffff,
> > 4002f23cb11) fp = 4002f23cb11
> > 11c8d28(141d000, 4002f23d458, 100, 13aa000, 13b83ff, 4002f23d461,
> > 4002f23cbd1) fp = 4002f23cbd1
> > 11c827c(13b8000, 0, 13b83ff, 400047b1400, 40003b19330, 400047d5800,
> > 4002f23cc81) fp = 4002f23cc81
> > 1140a18(40003a1a750, 200, 40003a21e20, 4002f23db48, 0, 13b8000,
> > 4002f23cdc1) fp = 4002f23cdc1
> > 1137eb4(40003a1a750, 11c7f70, 1, 0, 2000, 0, 4002f23ce91) fp = 4002f23ce91
> > 11376c4(4002f23dac8, 40003a1a750, 4002f23db48, 2001, 4002f23daf8,
> > c044, 4002f23cf81) fp = 4002f23cf81
> > 1141b74(4002f23dac8, 40004296020, 4002f23db08, 0, 400044ef800, 400,
> > 4002f23d0a1) fp = 4002f23d0a1
> > 113d3f4(4002f23dac8, 20001, 44, 40004333f20, 0, 16, 4002f23d1f1) fp =
> > 4002f23d1f1
> > 113d254(40004296020, 4002f23dac8, 20001, 20000, 1, 0, 4002f23d461) fp
> > = 4002f23d461
> > 1308818(40004296020, 4002f23ddd8, 4002f23ddc8, 141e892, 11d891c, 2e,
> > 4002f23d511) fp = 4002f23d511
> > 1011b64(4002f23ded0, 405, 40004296020, 113d23c, 50, 5, 4002f23d621) fp
> > = 4002f23d621
> > 23e800(2fde7bb40, 20000, 0, 0, cc, 0, fffffffffffd3211) fp = 
> > fffffffffffd3211
> >
> > dump to dev 5,1 not possible
> > rebooting
> >
> >
> > dmesg bsd.rd 6.6:
> >
> > Booting /pci@1c,600000/network@3/bsd.rd
> > 4190432@0x1000000+3872@0x13ff0e0+3252800@0x1c00000+941504@0x1f1a240
> > symbols @ 0xfec4e400 165+363672+220023 start=0x1000000
> > console is /pci@1e,600000/isa@7/serial@0,3f8
> > Copyright (c) 1982, 1986, 1989, 1991, 1993
> >         The Regents of the University of California.  All rights reserved.
> > Copyright (c) 1995-2019 OpenBSD. All rights reserved.  
> > https://www.OpenBSD.org
> >
> > OpenBSD 6.6 (RAMDISK) #84: Sat Oct 12 10:42:12 MDT 2019
> >     dera...@sparc64.openbsd.org:/usr/src/sys/arch/sparc64/compile/RAMDISK
> > real mem = 2147483648 (2048MB)
> > avail mem = 2098487296 (2001MB)
> > mainbus0 at root: Sun Blade 2500 (Silver)
> > "SUNW,UltraSPARC-IIIi" at mainbus0 not configured
> > cpu0 at mainbus0: SUNW,UltraSPARC-IIIi (rev 3.4) @ 1600 MHz
> > cpu0: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K
> > external (64 b/l)
> > "memory-controller" at mainbus0 not configured
> > "memory-controller" at mainbus0 not configured
> > schizo0 at mainbus0: "Tomatillo", version 4, ign 700, bus A 0 to 0
> > schizo0: dvma map c0000000-dfffffff
> > pci0 at schizo0
> > bge0 at pci0 dev 3 function 0 "Broadcom BCM5703" rev 0x00,
> > BCM5702/5703 A2 (0x1002)bge0: nvram lock timed out
> > : ivec 0x71c, address 00:03:ba:f2:ee:53
> > brgphy0 at bge0 phy 1: BCM5703 10/100/1000baseT PHY, rev. 2
> > "ppm" at mainbus0 not configured
> > schizo1 at mainbus0: "Tomatillo", version 4, ign 740, bus B 0 to 0
> > schizo1: dvma map c0000000-dfffffff
> > pci1 at schizo1
> > mpi0 at pci1 dev 4 function 0 "Symbios Logic 53c1030" rev 0x07: ivec 0x769
> > mpi0: 0, firmware 1.3.11.1
> > scsibus0 at mpi0: 16 targets, initiator 7
> > sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST314670LSUN146G, 045A>
> > serial.SEAGATE_ST314670LSUN146G4442RJNV_3KS2RJNV
> > sd0: 140009MB, 512 bytes/sector, 286739329 sectors
> > mpi0: target 0 Sync at 160MHz width 16bit offset 63 QAS 1 DT 1 IU 1
> > mpi1 at pci1 dev 4 function 1 "Symbios Logic 53c1030" rev 0x07: ivec 0x768
> > mpi1: 0, firmware 1.3.11.1
> > scsibus1 at mpi1: 16 targets, initiator 7
> > schizo2 at mainbus0: "Tomatillo", version 4, ign 780, bus A 0 to 1
> > schizo2: dvma map c0000000-dfffffff
> > pci2 at schizo2
> > ebus0 at pci2 dev 7 function 0 "Acer Labs M1533 ISA" rev 0x00
> > "flashprom" at ebus0 addr 0-fffff not configured
> > rtc0 at ebus0 addr 70-71: m5823
> > "i2c" at ebus0 addr 320-321 ivec 0x2e not configured
> > "power" at ebus0 addr 800-82f ivec 0x20 not configured
> > com0 at ebus0 addr 3f8-3ff ivec 0x2c: ns16550a, 16 byte fifo
> > com0: console
> > com1 at ebus0 addr 2e8-2ef ivec 0x2c: ns16550a, 16 byte fifo
> > "dma" at ebus0 addr 0-ffff not configured
> > "Acer Labs M7101 Power" rev 0x00 at pci2 dev 6 function 0 not configured
> > "Acer Labs M5451 Audio" rev 0x02 at pci2 dev 8 function 0 not configured
> > ohci0 at pci2 dev 10 function 0 "Acer Labs M5237 USB" rev 0x03: ivec
> > 0x7a7, version 1.0, legacy support
> > ohci1 at pci2 dev 11 function 0 "Acer Labs M5237 USB" rev 0x03: ivec
> > 0x7a6, version 1.0, legacy support
> > pciide0 at pci2 dev 13 function 0 "Acer Labs M5229 UDMA IDE" rev 0xc4:
> > DMA, channel 0 configured to native-PCI, channel 1 configured to
> > native-PCI
> > pciide0: using ivec 0x798 for native-PCI interrupt
> > pciide0: channel 0 disabled (no drives)
> > atapiscsi0 at pciide0 channel 1 drive 0
> > scsibus2 at atapiscsi0: 2 targets
> > cd0 at scsibus2 targ 0 lun 0: <TSSTcorp, CDW/DVD TS-H492C, SI00> removable
> > cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
> > radeonfb0 at pci2 dev 2 function 0 "ATI Radeon VE" rev 0x00
> > radeonfb0: SUNW,375-3181, 1152x900
> > wsdisplay0 at radeonfb0
> > wsdisplay0: screen 0 added (std, sun emulation)
> > ppb0 at pci2 dev 4 function 0 "TI PCI2250" rev 0x02
> > pci3 at ppb0 bus 1
> > ohci2 at pci3 dev 8 function 0 "NEC USB" rev 0x43: ivec 0x794, version 1.0
> > ohci3 at pci3 dev 8 function 1 "NEC USB" rev 0x43: ivec 0x795, version 1.0
> > ehci0 at pci3 dev 8 function 2 "NEC USB" rev 0x04: ivec 0x796
> > usb0 at ehci0: USB revision 2.0
> > uhub0 at usb0 configuration 1 interface 0 "NEC EHCI root hub" rev
> > 2.00/1.00 addr 1
> > "TI TSB43AB23 FireWire" rev 0x00 at pci3 dev 11 function 0 not configured
> > usb1 at ohci2: USB revision 1.0
> > uhub1 at usb1 configuration 1 interface 0 "NEC OHCI root hub" rev
> > 1.00/1.00 addr 1
> > usb2 at ohci3: USB revision 1.0
> > uhub2 at usb2 configuration 1 interface 0 "NEC OHCI root hub" rev
> > 1.00/1.00 addr 1
> > usb3 at ohci0: USB revision 1.0
> > uhub3 at usb3 configuration 1 interface 0 "Acer Labs OHCI root hub"
> > rev 1.00/1.00 addr 1
> > usb4 at ohci1: USB revision 1.0
> > uhub4 at usb4 configuration 1 interface 0 "Acer Labs OHCI root hub"
> > rev 1.00/1.00 addr 1
> > "ppm" at mainbus0 not configured
> > schizo3 at mainbus0: "Tomatillo", version 4, ign 7c0, bus B 0 to 0
> > schizo3: dvma map c0000000-dfffffff
> > pci4 at schizo3
> > "i2c" at mainbus0 not configured
> > softraid0 at root
> > scsibus3 at softraid0: 256 targets
> > bootpath: /pci@1c,600000/network@3,0
> > root on rd0a swap on rd0b dump on rd0b
> >
> > dmesg 6.6:
> > console is /pci@1e,600000/isa@7/serial@0,3f8
> > Copyright (c) 1982, 1986, 1989, 1991, 1993
> >         The Regents of the University of California.  All rights reserved.
> > Copyright (c) 1995-2019 OpenBSD. All rights reserved.  
> > https://www.OpenBSD.org
> >
> > OpenBSD 6.6 (GENERIC.MP) #88: Sat Oct 12 10:16:48 MDT 2019
> >     dera...@sparc64.openbsd.org:/usr/src/sys/arch/sparc64/compile/GENERIC.MP
> > real mem = 2147483648 (2048MB)
> > avail mem = 2092843008 (1995MB)
> > mpath0 at root
> > scsibus0 at mpath0: 256 targets
> > mainbus0 at root: Sun Blade 2500 (Silver)
> > cpu0 at mainbus0: SUNW,UltraSPARC-IIIi (rev 3.4) @ 1600 MHz
> > cpu0: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K
> > external (64 b/l)
> > cpu1 at mainbus0: SUNW,UltraSPARC-IIIi (rev 3.4) @ 1600 MHz
> > cpu1: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K
> > external (64 b/l)
> > "memory-controller" at mainbus0 not configured
> > "memory-controller" at mainbus0 not configured
> > schizo0 at mainbus0: "Tomatillo", version 4, ign 700, bus A 0 to 0
> > schizo0: dvma map c0000000-dfffffff
> > pci0 at schizo0
> > bge0 at pci0 dev 3 function 0 "Broadcom BCM5703" rev 0x00,
> > BCM5702/5703 A2 (0x1002): ivec 0x71c, address 00:03:ba:f2:ee:53
> > brgphy0 at bge0 phy 1: BCM5703 10/100/1000baseT PHY, rev. 2
> > "ppm" at mainbus0 not configured
> > schizo1 at mainbus0: "Tomatillo", version 4, ign 740, bus B 0 to 0
> > schizo1: dvma map c0000000-dfffffff
> > pci1 at schizo1
> > mpi0 at pci1 dev 4 function 0 "Symbios Logic 53c1030" rev 0x07: ivec 0x769
> > mpi0: 0, firmware 1.3.11.1
> > scsibus1 at mpi0: 16 targets, initiator 7
> > sym0 at scsibus1 targ 0 lun 0: <SEAGATE, ST314670LSUN146G, 045A>
> > serial.SEAGATE_ST314670LSUN146G4442RJNV_3KS2RJNV
> > sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST314670LSUN146G, 045A>
> > serial.SEAGATE_ST314670LSUN146G4442RJNV_3KS2RJNV
> > sd0: 140009MB, 512 bytes/sector, 286739329 sectors
> > mpi0: target 0 Sync at 160MHz width 16bit offset 63 QAS 1 DT 1 IU 1
> > mpi1 at pci1 dev 4 function 1 "Symbios Logic 53c1030" rev 0x07: ivec 0x768
> > mpi1: 0, firmware 1.3.11.1
> > scsibus2 at mpi1: 16 targets, initiator 7
> > schizo2 at mainbus0: "Tomatillo", version 4, ign 780, bus A 0 to 1
> > schizo2: dvma map c0000000-dfffffff
> > pci2 at schizo2
> > ebus0 at pci2 dev 7 function 0 "Acer Labs M1533 ISA" rev 0x00
> > "flashprom" at ebus0 addr 0-fffff not configured
> > rtc0 at ebus0 addr 70-71: m5823
> > pcfiic0 at ebus0 addr 320-321 ivec 0x2e
> > iic0 at pcfiic0
> > "SUNW,i2c-imax" at iic0 addr 0x9 not configured
> > "pca9556" at iic0 addr 0x18 not configured
> > "SUNW,i2c-auxfan1" at iic0 addr 0x29 not configured
> > admtt0 at iic0 addr 0x2c
> > admtt1 at iic0 addr 0x2e
> > "fm3560" at iic0 addr 0x37 not configured
> > "fm3560" at iic0 addr 0x4e not configured
> > spdmem0 at iic0 addr 0x5d: 512MB DDR SDRAM registered ECC PC2700CL2.5
> > spdmem1 at iic0 addr 0x5e: 512MB DDR SDRAM registered ECC PC2700CL2.5
> > spdmem2 at iic0 addr 0x65: 512MB DDR SDRAM registered ECC PC2700CL2.5
> > spdmem3 at iic0 addr 0x66: 512MB DDR SDRAM registered ECC PC2700CL2.5
> > "ics951601" at iic0 addr 0x69 not configured
> > power0 at ebus0 addr 800-82f ivec 0x20
> > com0 at ebus0 addr 3f8-3ff ivec 0x2c: ns16550a, 16 byte fifo
> > com0: console
> > com1 at ebus0 addr 2e8-2ef ivec 0x2c: ns16550a, 16 byte fifo
> > "dma" at ebus0 addr 0-ffff not configured
> > alipm0 at pci2 dev 6 function 0 "Acer Labs M7101 Power" rev 0x00: 223KHz 
> > clock
> > iic1 at alipm0
> > "scm001" at alipm0 addr 0x20 skipped due to alipm0 bugs
> > autri0 at pci2 dev 8 function 0 "Acer Labs M5451 Audio" rev 0x02: ivec 0x7a4
> > ac97: codec id 0x41445348 (Analog Devices AD1881A)
> > ac97: codec features headphone, Analog Devices Phat Stereo
> > audio0 at autri0
> > midi0 at autri0: <4DWAVE MIDI UART>
> > ohci0 at pci2 dev 10 function 0 "Acer Labs M5237 USB" rev 0x03: ivec
> > 0x7a7, version 1.0, legacy support
> > ohci1 at pci2 dev 11 function 0 "Acer Labs M5237 USB" rev 0x03: ivec
> > 0x7a6, version 1.0, legacy support
> > pciide0 at pci2 dev 13 function 0 "Acer Labs M5229 UDMA IDE" rev 0xc4:
> > DMA, channel 0 configured to native-PCI, channel 1 configured to
> > native-PCI
> > pciide0: using ivec 0x798 for native-PCI interrupt
> > pciide0: channel 0 disabled (no drives)
> > atapiscsi0 at pciide0 channel 1 drive 0
> > scsibus3 at atapiscsi0: 2 targets
> > cd0 at scsibus3 targ 0 lun 0: <TSSTcorp, CDW/DVD TS-H492C, SI00> removable
> > cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
> > radeondrm0 at pci2 dev 2 function 0 "ATI Radeon VE" rev 0x00
> > drm0 at radeondrm0
> > radeondrm0: ivec 0x78c
> > ppb0 at pci2 dev 4 function 0 "TI PCI2250" rev 0x02
> > pci3 at ppb0 bus 1
> > ohci2 at pci3 dev 8 function 0 "NEC USB" rev 0x43: ivec 0x794, version 1.0
> > ohci3 at pci3 dev 8 function 1 "NEC USB" rev 0x43: ivec 0x795, version 1.0
> > ehci0 at pci3 dev 8 function 2 "NEC USB" rev 0x04: ivec 0x796
> > usb0 at ehci0: USB revision 2.0
> > uhub0 at usb0 configuration 1 interface 0 "NEC EHCI root hub" rev
> > 2.00/1.00 addr 1
> > "TI TSB43AB23 FireWire" rev 0x00 at pci3 dev 11 function 0 not configured
> > usb1 at ohci2: USB revision 1.0
> > uhub1 at usb1 configuration 1 interface 0 "NEC OHCI root hub" rev
> > 1.00/1.00 addr 1
> > usb2 at ohci3: USB revision 1.0
> > uhub2 at usb2 configuration 1 interface 0 "NEC OHCI root hub" rev
> > 1.00/1.00 addr 1
> > usb3 at ohci0: USB revision 1.0
> > uhub3 at usb3 configuration 1 interface 0 "Acer Labs OHCI root hub"
> > rev 1.00/1.00 addr 1
> > usb4 at ohci1: USB revision 1.0
> > uhub4 at usb4 configuration 1 interface 0 "Acer Labs OHCI root hub"
> > rev 1.00/1.00 addr 1
> > "ppm" at mainbus0 not configured
> > schizo3 at mainbus0: "Tomatillo", version 4, ign 7c0, bus B 0 to 0
> > schizo3: dvma map c0000000-dfffffff
> > pci4 at schizo3
> > "i2c" at mainbus0 not configured
> > vscsi0 at root
> > scsibus4 at vscsi0: 256 targets
> > softraid0 at root
> > scsibus5 at softraid0: 256 targets
> > bootpath: /pci@1d,700000/scsi@4,0/disk@0,0
> > root on sd0a (c38700025a879733.a) swap on sd0b dump on sd0b
> > initializing kernel modesetting (RV100 0x1002:0x5159 0x1002:0x0908 0x00).
> > BIOS signature incorrect 0 0
> > radeondrm0: 1152x900, 8bpp
> > wsdisplay0 at radeondrm0 mux 1
> > wsdisplay0: screen 0 added (std, sun emulation)
> >
> > 6.7-beta after installing it with the 6.6 bsd.rd:
> >
> > OpenBSD IEEE 1275 Bootblock 2.0
> > ..>> OpenBSD BOOT 1.17
> > Trying bsd...
> > Booting /pci@1d,700000/scsi@4/disk@0,0:a/bsd
> > 11196424@0x1000000+2040@0x1aad808+188272@0x1c00000+4006032@0x1c2df70
> > symbols @ 0xfec46440 175+587856+405269 start=0x1000000
> > [ using 994392 bytes of bsd ELF symbol table ]
> > console is /pci@1e,600000/isa@7/serial@0,3f8
> > Copyright (c) 1982, 1986, 1989, 1991, 1993
> >         The Regents of the University of California.  All rights
> > reserved.
> > Copyright (c) 1995-2020 OpenBSD. All rights reserved.
> > https://www.OpenBSD.org
> >
> > OpenBSD 6.7-beta (GENERIC.MP) #270: Mon Apr  6 18:39:29 MDT 2020
> >     dera...@sparc64.openbsd.org:/usr/src/sys/arch/sparc64/compile/GENERIC.MP
> > real mem = 2147483648 (2048MB)
> > avail mem = 2091376640 (1994MB)
> > mpath0 at root
> > scsibus0 at mpath0: 256 targets
> > mainbus0 at root: Sun Blade 2500 (Silver)
> > cpu0 at mainbus0: SUNW,UltraSPARC-IIIi (rev 3.4) @ 1600 MHz
> > cpu0: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K
> > external (64 b/l)
> > cpu1 at mainbus0: SUNW,UltraSPARC-IIIi (rev 3.4) @ 1600 MHz
> > cpu1: physical 32K instruction (32 b/l), 64K data (32 b/l), 1024K
> > external (64 b/l)
> > "memory-controller" at mainbus0 not configured
> > "memory-controller" at mainbus0 not configured
> > schizo0 at mainbus0: "Tomatillo", version 4, ign 700, bus A 0 to 0
> > schizo0: dvma map c0000000-dfffffff
> > pci0 at schizo0
> > bge0 at pci0 dev 3 function 0 "Broadcom BCM5703" rev 0x00,
> > BCM5702/5703 A2 (0x1002): ivec 0x71c, address 00:03:ba:f2:ee:53
> > brgphy0 at bge0 phy 1: BCM5703 10/100/1000baseT PHY, rev. 2
> > "ppm" at mainbus0 not configured
> > schizo1 at mainbus0: "Tomatillo", version 4, ign 740, bus B 0 to 0
> > schizo1: dvma map c0000000-dfffffff
> > pci1 at schizo1
> > mpi0 at pci1 dev 4 function 0 "Symbios Logic 53c1030" rev 0x07: ivec
> > 0x769
> > mpi0: 0, firmware 1.3.11.1
> > scsibus1 at mpi0: 16 targets, initiator 7
> > sym0 at scsibus1 targ 0 lun 0: <SEAGATE, ST314670LSUN146G, 045A>
> > serial.SEAGATE_ST314670LSUN146G4442RJNV_3KS2RJNV
> > sd0 at scsibus0 targ 0 lun 0: <SEAGATE, ST314670LSUN146G, 045A>
> > serial.SEAGATE_ST314670LSUN146G4442RJNV_3KS2RJNV
> > sd0: 140009MB, 512 bytes/sector, 286739329 sectors
> > mpi0: target 0 Sync at 160MHz width 16bit offset 63 QAS 1 DT 1 IU 1
> > mpi1 at pci1 dev 4 function 1 "Symbios Logic 53c1030" rev 0x07: ivec
> > 0x768
> > mpi1: 0, firmware 1.3.11.1
> > scsibus2 at mpi1: 16 targets, initiator 7
> > schizo2 at mainbus0: "Tomatillo", version 4, ign 780, bus A 0 to 1
> > schizo2: dvma map c0000000-dfffffff
> > pci2 at schizo2
> > ebus0 at pci2 dev 7 function 0 "Acer Labs M1533 ISA" rev 0x00
> > "flashprom" at ebus0 addr 0-fffff not configured
> > rtc0 at ebus0 addr 70-71: m5823
> > pcfiic0 at ebus0 addr 320-321 ivec 0x2e
> > iic0 at pcfiic0
> > "SUNW,i2c-imax" at iic0 addr 0x9 not configured
> > "pca9556" at iic0 addr 0x18 not configured
> > "SUNW,i2c-auxfan1" at iic0 addr 0x29 not configured
> > admtt0 at iic0 addr 0x2c
> > admtt1 at iic0 addr 0x2e
> > "fm3560" at iic0 addr 0x37 not configured
> > "fm3560" at iic0 addr 0x4e not configured
> > spdmem0 at iic0 addr 0x5d: 512MB DDR SDRAM registered ECC PC2700CL2.5
> > spdmem1 at iic0 addr 0x5e: 512MB DDR SDRAM registered ECC PC2700CL2.5
> > spdmem2 at iic0 addr 0x65: 512MB DDR SDRAM registered ECC PC2700CL2.5
> > spdmem3 at iic0 addr 0x66: 512MB DDR SDRAM registered ECC PC2700CL2.5
> > "ics951601" at iic0 addr 0x69 not configured
> > power0 at ebus0 addr 800-82f ivec 0x20
> > com0 at ebus0 addr 3f8-3ff ivec 0x2c: ns16550a, 16 byte fifo
> > com0: console
> > com1 at ebus0 addr 2e8-2ef ivec 0x2c: ns16550a, 16 byte fifo
> > "dma" at ebus0 addr 0-ffff not configured
> > alipm0 at pci2 dev 6 function 0 "Acer Labs M7101 Power" rev 0x00:
> > 223KHz clock
> > iic1 at alipm0
> > "scm001" at alipm0 addr 0x20 skipped due to alipm0 bugs
> > autri0 at pci2 dev 8 function 0 "Acer Labs M5451 Audio" rev 0x02: ivec
> > 0x7a4
> > ac97: codec id 0x41445348 (Analog Devices AD1881A)
> > ac97: codec features headphone, Analog Devices Phat Stereo
> > audio0 at autri0
> > midi0 at autri0: <4DWAVE MIDI UART>
> > ohci0 at pci2 dev 10 function 0 "Acer Labs M5237 USB" rev 0x03: ivec
> > 0x7a7, version 1.0, legacy support
> > ohci1 at pci2 dev 11 function 0 "Acer Labs M5237 USB" rev 0x03: ivec
> > 0x7a6, version 1.0, legacy support
> > pciide0 at pci2 dev 13 function 0 "Acer Labs M5229 UDMA IDE" rev 0xc4:
> > DMA, channel 0 configured to native-PCI, channel 1 configured to
> > native-PCI
> > pciide0: using ivec 0x798 for native-PCI interrupt
> > pciide0: channel 0 disabled (no drives)
> > atapiscsi0 at pciide0 channel 1 drive 0
> > scsibus3 at atapiscsi0: 2 targets
> > cd0 at scsibus3 targ 0 lun 0: <TSSTcorp, CDW/DVD TS-H492C, SI00>
> > removable
> > cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
> > radeondrm0 at pci2 dev 2 function 0 "ATI Radeon VE" rev 0x00
> > drm0 at radeondrm0
> > radeondrm0: ivec 0x78c
> > ppb0 at pci2 dev 4 function 0 "TI PCI2250" rev 0x02
> > pci3 at ppb0 bus 1
> > ohci2 at pci3 dev 8 function 0 "NEC USB" rev 0x43: ivec 0x794, version
> > 1.0
> > ohci3 at pci3 dev 8 function 1 "NEC USB" rev 0x43: ivec 0x795, version
> > 1.0
> > ehci0 at pci3 dev 8 function 2 "NEC USB" rev 0x04: ivec 0x796
> > usb0 at ehci0: USB revision 2.0
> > uhub0 at usb0 configuration 1 interface 0 "NEC EHCI root hub" rev
> > 2.00/1.00 addr 1
> > "TI TSB43AB23 FireWire" rev 0x00 at pci3 dev 11 function 0 not
> > configured
> > usb1 at ohci2: USB revision 1.0
> > uhub1 at usb1 configuration 1 interface 0 "NEC OHCI root hub" rev
> > 1.00/1.00 addr 1
> > usb2 at ohci3: USB revision 1.0
> > uhub2 at usb2 configuration 1 interface 0 "NEC OHCI root hub" rev
> > 1.00/1.00 addr 1
> > usb3 at ohci0: USB revision 1.0
> > uhub3 at usb3 configuration 1 interface 0 "Acer Labs OHCI root hub"
> > rev 1.00/1.00 addr 1
> > usb4 at ohci1: USB revision 1.0
> > uhub4 at usb4 configuration 1 interface 0 "Acer Labs OHCI root hub"
> > rev 1.00/1.00 addr 1
> > "ppm" at mainbus0 not configured
> > schizo3 at mainbus0: "Tomatillo", version 4, ign 7c0, bus B 0 to 0
> > schizo3: dvma map c0000000-dfffffff
> > pci4 at schizo3
> > "i2c" at mainbus0 not configured
> > vscsi0 at root
> > scsibus4 at vscsi0: 256 targets
> > softraid0 at root
> > scsibus5 at softraid0: 256 targets
> > bootpath: /pci@1d,700000/scsi@4,0/disk@0,0
> > root on sd0a (c7e58360e1193129.a) swap on sd0b dump on sd0b
> > initializing kernel modesetting (RV100 0x1002:0x5159 0x1002:0x0908 0x00).
> > BIOS signature incorrect 0 0
> > radeon_cp: Failed to load firmware "radeon/R100_cp.bin"
> > [drm] *ERROR* Failed to load firmware!
> > drm:pid0:r100_startup *ERROR* failed initializing CP (-2).
> > drm:pid0:r100_init *ERROR* Disabling GPU acceleration
> > radeondrm0: 1152x900, 8bpp
> > wsdisplay0 at radeondrm0 mux 1
> > wsdisplay0: screen 0 added (std, sun emulation)
> > Automatic boot in progress: starting file system checks.
> > /dev/sd0a (c7e58360e1193129.a): file system is clean; not checking
> > /dev/sd0k (c7e58360e1193129.k): file system is clean; not checking
> > /dev/sd0d (c7e58360e1193129.d): file system is clean; not checking
> > /dev/sd0f (c7e58360e1193129.f): file system is clean; not checking
> > /dev/sd0g (c7e58360e1193129.g): file system is clean; not checking
> > /dev/sd0h (c7e58360e1193129.h): file system is clean; not checking
> > /dev/sd0j (c7e58360e1193129.j): file system is clean; not checking
> > /dev/sd0i (c7e58360e1193129.i): file system is clean; not checking
> > /dev/sd0e (c7e58360e1193129.e): file system is clean; not checking
> > pf enabled
> > starting network
> > bge0: 192.168.2.131 lease accepted from 192.168.2.1 (fe:e1:ba:d2:bf:d6)
> > reordering libraries:Illegal instruction (core dumped)
> > Illegal instruction (core dumped)
> > Illegal instruction (core dumped)
> >  failed.
> > Illegal instruction (core dumped)
> > openssl: generating isakmpd/iked RSA keys... failed.
> > cp: /etc/isakmpd/private/local.key: No such file or directory
> > chmod: /etc/iked/private/local.key: No such file or directory
> > cp: /etc/isakmpd/local.pub: No such file or directory
> > Segmentation fault (core dumped)
> > Illegal instruction (core dumped)
> > starting early daemons:Illegal instruction (core dumped)
> > Illegal instruction (core dumped)
> > usage: /etc/rc.d/syslogd [-df] start|stop|restart|reload|check
> > Illegal instruction (core dumped)
> > Illegal instruction (core dumped)
> > usage: /etc/rc.d/pflogd [-df] start|stop|restart|reload|check
> > Illegal instruction (core dumped)
> > Illegal instruction (core dumped)
> > usage: /etc/rc.d/ntpd [-df] start|stop|restart|check
> > .
> > starting RPC daemons:.
> > savecore: no core dump
> > checking quotas: done.
> > Illegal instruction (core dumped)
> > Illegal instruction (core dumped)
> > Illegal instruction (core dumped)
> > clearing /tmp
> > Illegal instruction (core dumped)
> > kern.securelevel: 0 -> 1
> > Illegal instruction (core dumped)
> > creating runtime link editor directory cache.
> > preserving editor files.
> > Illegal instruction (core dumped)
> > starting network daemons:Illegal instruction (core dumped)
> > Illegal instruction (core dumped)
> > usage: /etc/rc.d/sshd [-df] start|stop|restart|reload|check
> > Illegal instruction (core dumpeddev = 0x700, block = 25904, fs = /
> > panic: ffs_blkfree: freeing free block
> > Stopped at      db_enter+0x8:   nop
> >     TID    PID    UID     PRFLAGS     PFLAGS  CPU  COMMAND
> > *176722  48187      0    0x100803     0x2000    1K grep
> > panic(1, 4002753d318, 1c24758, 100, 1cba000, 0) at panic+0x148
> > ffs_blkfree(1950000, ca6, d5e, 40004542800, 6530, 4000ee82000) at 
> > ffs_blkfree+0
> > x800
> > ffs_indirtrunc(400041c25c0, f6c, 6530, 0, 86, fffffffffffff002) at 
> > ffs_indirtru
> > nc+0x384
> > ffs_truncate(400041c25c0, 0, 0, 0, 2, 0) at ffs_truncate+0xb28
> > ufs_setattr(4002753d828, 40004315ce0, 400041c25c0, 400042fd0c0, 1545aa0, 1) 
> > at u
> > fs_setattr+0x408
> > VOP_SETATTR(400042fd0c0, 175867c, 1, 400042aaf30, 1aad000, 
> > bceb5949771b0976) at
> >  VOP_SETATTR+0x54
> > coredump(400042aaf30, 1c8e6f8, 40004200000, 40004315ce0, 4002753d938, 
> > 400042fd0
> > c0) at coredump+0x380
> > sigexit(400042aaf30, 4, 0, 50, 1, 0) at sigexit+0x9c
> > postsig(400042aaf30, 4, 400042a9b20, 4, 0, 1aad000) at postsig+0x1b8
> > userret(400042aaf30, 400042aafc0, 8, 0, 0, 400042a9b20) at userret+0xd4
> > trap(4002753ded0, fab193, 211e88b3a0, 400042aaf30, 1aad000, fa8000) at 
> > trap+0x9
> > 40
> > Lslowtrap_reenter(2102bd2000, 450, 3, 1002, ffffffffffffffff, 0) at 
> > Lslowtrap_r
> > eenter+0xf8
> > https://www.openbsd.org/ddb.html describes the minimum info required in bug
> > reports.  Insufficient info makes it difficult to find and fix bugs.
> > ddb{1}> trace
> > panic(1, 4002753d318, 1c24758, 100, 1cba000, 0) at panic+0x148
> > ffs_blkfree(1950000, ca6, d5e, 40004542800, 6530, 4000ee82000) at 
> > ffs_blkfree+0
> > x800
> > ffs_indirtrunc(400041c25c0, f6c, 6530, 0, 86, fffffffffffff002) at 
> > ffs_indirtru
> > nc+0x384
> > ffs_truncate(400041c25c0, 0, 0, 0, 2, 0) at ffs_truncate+0xb28
> > ufs_setattr(4002753d828, 40004315ce0, 400041c25c0, 400042fd0c0, 1545aa0, 1) 
> > at u
> > fs_setattr+0x408
> > VOP_SETATTR(400042fd0c0, 175867c, 1, 400042aaf30, 1aad000, 
> > bceb5949771b0976) at
> >  VOP_SETATTR+0x54
> > coredump(400042aaf30, 1c8e6f8, 40004200000, 40004315ce0, 4002753d938, 
> > 400042fd0
> > c0) at coredump+0x380
> > sigexit(400042aaf30, 4, 0, 50, 1, 0) at sigexit+0x9c
> > postsig(400042aaf30, 4, 400042a9b20, 4, 0, 1aad000) at postsig+0x1b8
> > userret(400042aaf30, 400042aafc0, 8, 0, 0, 400042a9b20) at userret+0xd4
> > trap(4002753ded0, fab193, 211e88b3a0, 400042aaf30, 1aad000, fa8000) at 
> > trap+0x9
> > 40
> > Lslowtrap_reenter(2102bd2000, 450, 3, 1002, ffffffffffffffff, 0) at 
> > Lslowtrap_r
> > eenter+0xf8
> > ddb{1}> ps
> >    PID     TID   PPID    UID  S       FLAGS  WAIT          COMMAND
> > *48187  176722  88537      0  7    0x102803                grep
> >  88537  382815  99841      0  3    0x10008b  pause         ksh
> >  66999   94861      1     77  3    0x100090  poll          dhclient
> >  48420  280249      1      0  3        0x80  poll          dhclient
> >  40518  319937  85231    115  3    0x100092  kqread        slaacd
> >  85838  489306  85231    115  3    0x100092  kqread        slaacd
> >  85231  202308      1      0  3    0x100080  kqread        slaacd
> >  99841  236206      1      0  3    0x10008b  pause         sh
> >  81405   79355      0      0  3     0x14200  bored         radeon-crtc
> >  71770   73324      0      0  3     0x14200  bored         radeon-crtc
> >  59905  423050      0      0  3     0x14200  bored         ttm_swap
> >  63119  314087      0      0  3     0x14200  bored         smr
> >  97636  219885      0      0  3     0x14200  pgzero        zerothread
> >   1514   49286      0      0  3     0x14200  aiodoned      aiodoned
> >  14539   49447      0      0  3     0x14200  syncer        update
> >   9416  340174      0      0  3     0x14200  cleaner       cleaner
> >  87399    2990      0      0  3     0x14200  reaper        reaper
> >  50862  213556      0      0  3     0x14200  pgdaemon      pagedaemon
> >  92067  192338      0      0  3     0x14200  bored         crynlk
> >  54009  434311      0      0  3     0x14200  bored         crypto
> >  37503  355741      0      0  3     0x14200  usbtsk        usbtask
> >  75750  328255      0      0  3     0x14200  usbatsk       usbatsk
> >  13762  140473      0      0  3     0x14200  bored         drmtskl
> >  28060  134348      0      0  3     0x14200  bored         drmlwq
> >  37420   87687      0      0  3     0x14200  bored         drmlwq
> >  47187  479949      0      0  3     0x14200  bored         drmlwq
> >  63862   19851      0      0  3     0x14200  bored         drmlwq
> >  20716  145865      0      0  3     0x14200  bored         drmubwq
> >   9815  176299      0      0  3     0x14200  bored         drmubwq
> >  61058  227276      0      0  3     0x14200  bored         drmubwq
> >  68348  317421      0      0  3     0x14200  bored         drmubwq
> >  10263  108304      0      0  3     0x14200  bored         drmwq
> >  59225  524108      0      0  3     0x14200  bored         drmwq
> >  47024  166127      0      0  3     0x14200  bored         drmwq
> >  97890  482048      0      0  3     0x14200  bored         drmwq
> >  16681  130387      0      0  3     0x14200  bored         sensors
> >  79577  459066      0      0  3  0x40014200                idle1
> >  30879  347784      0      0  3     0x14200  bored         softnet
> >  73065   27334      0      0  3     0x14200  bored         systqmp
> >  96778  411122      0      0  3     0x14200  bored         systq
> >  85835  217328      0      0  3  0x40014200  bored         softclock
> >  71127    1246      0      0  7  0x40014200                idle0
> >  96626  508362      0      0  3     0x14200  kmalloc       kmthread
> >      1  419877      0      0  3        0x82  wait          init
> >      0       0     -1      0  3     0x10200  scheduler     swapper
> > ddb{1}> machine ddbcpu 0
> > panic: kernel data fault: pc=182bab4 addr=182a000
> > Stopped at      _kernel_lock+0xd0:      ld              [%i0 + 0x800], %i3
> > intr_handler(e0017b80, 4000449e800, 0, 6, 6c, 1cbff48) at intr_handler+0x30
> > sparc_intr_retry(72e43b48, 72e266ba, 8, 2, 1, 1a39840) at 
> > sparc_intr_retry+0x5c
> >
> > sys_tickintr(1cd165c, 2018000, 2b1e8, 2b1e7, 2b1e7, 2b1e8) at 
> > sys_tickintr+0xc4
> >
> > intr_handler(e0017ec8, 4000431e300, 0, 1, 0, 1f195) at intr_handler+0x30
> > sparc_intr_retry(3, 0, 0, 0, 2018000, 1aad000) at sparc_intr_retry+0x5c
> > sched_idle(2018000, 2018140, 1c8f2f8, 1903fde, 400042ee780, 1caf5f0) at 
> > sched_i
> > dle+0x27c
> > proc_trampoline(0, 0, 0, 0, 0, 0) at proc_trampoline+0x14
> > ddb{0}> trace
> > intr_handler(e0017b80, 4000449e800, 0, 6, 6c, 1cbff48) at intr_handler+0x30
> > sparc_intr_retry(72e43b48, 72e266ba, 8, 2, 1, 1a39840) at 
> > sparc_intr_retry+0x5c
> >
> > sys_tickintr(1cd165c, 2018000, 2b1e8, 2b1e7, 2b1e7, 2b1e8) at 
> > sys_tickintr+0xc4
> >
> > intr_handler(e0017ec8, 4000431e300, 0, 1, 0, 1f195) at intr_handler+0x30
> > sparc_intr_retry(3, 0, 0, 0, 2018000, 1aad000) at sparc_intr_retry+0x5c
> > sched_idle(2018000, 2018140, 1c8f2f8, 1903fde, 400042ee780, 1caf5f0) at 
> > sched_i
> > dle+0x27c
> > proc_trampoline(0, 0, 0, 0, 0, 0) at proc_trampoline+0x14
> > ddb{0}> machine ddbcpu 1
> > Stopped at      db_enter+0x8:   nop
> > panic(1, 4002753c7a8, 1c24758, 104, 1cba000, 0) at panic+0x148
> > data_access_fault(1927000, 0, 182bab4, 182a000, 182bafc, 182a000) at 
> > data_acces
> > s_fault+0x320
> > Ldatafault_internal(8, 80, 4002753a000, 182bae2, 1, 1013120) at 
> > Ldatafault_inte
> > rnal+0xcc
> > db_read_bytes(182bafc, 3, 4002753cb10, 1, 1800000, 1000000) at 
> > db_read_bytes+0x
> > 58
> > db_put_value(182bafc, 4002753cb0f, 0, 1aad000, ffffffffffffffff, 
> > 4002753cb10) a
> > t db_put_value+0x6c
> > db_set_temp_breakpoint(91d02000, 1cac990, 4, 100000000, 1aad000, 0) at 
> > db_set_t
> > emp_breakpoint+0x74
> > db_set_single_step(1cd69f8, 182baf8, 1000000, 1000000, 0, 0) at 
> > db_set_single_s
> > tep+0xa8
> > db_restart_at_pc(1cd69f8, 0, 182baf8, 0, 1cb0000, 0) at 
> > db_restart_at_pc+0xe8
> > db_trap(1cd69f8, 1aad000, 0, 1c58000, 1, 1860000) at db_trap+0x208
> > db_ktrap(0, 4002753d020, 1cd6bd8, 101, 1cd6c80, 1cd69f8) at db_ktrap+0x1e4
> > trap(4002753d020, 101, 182baf4, bebf, 1aad000, 1d0006) at trap+0x1c0
> > Lslowtrap_reenter(1c24758, 1c37bfc, 0, 0, a, 0) at Lslowtrap_reenter+0xf8
> > printf(1, bceb5949771b0976, bceb5949771b0976, 0, 6b, 0) at printf+0x68
> > panic(1, 4002753d318, 1c24758, 100, 1cba000, 0) at panic+0x148
> > ddb{1}> trace
> > panic(1, 4002753c7a8, 1c24758, 104, 1cba000, 0) at panic+0x148
> > data_access_fault(1927000, 0, 182bab4, 182a000, 182bafc, 182a000) at 
> > data_acces
> > s_fault+0x320
> > Ldatafault_internal(8, 80, 4002753a000, 182bae2, 1, 1013120) at 
> > Ldatafault_inte
> > rnal+0xcc
> > db_read_bytes(182bafc, 3, 4002753cb10, 1, 1800000, 1000000) at 
> > db_read_bytes+0x
> > 58
> > db_put_value(182bafc, 4002753cb0f, 0, 1aad000, ffffffffffffffff, 
> > 4002753cb10) a
> > t db_put_value+0x6c
> > db_set_temp_breakpoint(91d02000, 1cac990, 4, 100000000, 1aad000, 0) at 
> > db_set_t
> > emp_breakpoint+0x74
> > db_set_single_step(1cd69f8, 182baf8, 1000000, 1000000, 0, 0) at 
> > db_set_single_s
> > tep+0xa8
> > db_restart_at_pc(1cd69f8, 0, 182baf8, 0, 1cb0000, 0) at 
> > db_restart_at_pc+0xe8
> > db_trap(1cd69f8, 1aad000, 0, 1c58000, 1, 1860000) at db_trap+0x208
> > db_ktrap(0, 4002753d020, 1cd6bd8, 101, 1cd6c80, 1cd69f8) at db_ktrap+0x1e4
> > trap(4002753d020, 101, 182baf4, bebf, 1aad000, 1d0006) at trap+0x1c0
> > Lslowtrap_reenter(1c24758, 1c37bfc, 0, 0, a, 0) at Lslowtrap_reenter+0xf8
> > printf(1, bceb5949771b0976, bceb5949771b0976, 0, 6b, 0) at printf+0x68
> > panic(1, 4002753d318, 1c24758, 100, 1cba000, 0) at panic+0x148
> > ffs_blkfree(1950000, ca6, d5e, 40004542800, 6530, 4000ee82000) at 
> > ffs_blkfree+0
> > x800
> > ffs_indirtrunc(400041c25c0, f6c, 6530, 0, 86, fffffffffffff002) at 
> > ffs_indirtru
> > nc+0x384
> > ffs_truncate(400041c25c0, 0, 0, 0, 2, 0) at ffs_truncate+0xb28
> > ufs_setattr(4002753d828, 40004315ce0, 400041c25c0, 400042fd0c0, 1545aa0, 1) 
> > at u
> > fs_setattr+0x408
> > VOP_SETATTR(400042fd0c0, 175867c, 1, 400042aaf30, 1aad000, 
> > bceb5949771b0976) at
> >  VOP_SETATTR+0x54
> > coredump(400042aaf30, 1c8e6f8, 40004200000, 40004315ce0, 4002753d938, 
> > 400042fd0
> > c0) at coredump+0x380
> > sigexit(400042aaf30, 4, 0, 50, 1, 0) at sigexit+0x9c
> > postsig(400042aaf30, 4, 400042a9b20, 4, 0, 1aad000) at postsig+0x1b8
> > userret(400042aaf30, 400042aafc0, 8, 0, 0, 400042a9b20) at userret+0xd4
> > trap(4002753ded0, fab193, 211e88b3a0, 400042aaf30, 1aad000, fa8000) at 
> > trap+0x9
> > 40
> > Lslowtrap_reenter(2102bd2000, 450, 3, 1002, ffffffffffffffff, 0) at 
> > Lslowtrap_r
> > eenter+0xf8
> >
> >
> > ddb{1}> boot halt
> >
> > RED State Exception
> > Error enable reg: 0000.0001.00f0.001f
> > CPU: 0000.0000.0000.0000
> > TL=0000.0000.0000.0005 TT=0000.0000.0000.0030
> >    TPC=0000.0000.0101.067c TnPC=0000.0000.0101.0680 
> > TSTATE=0000.0000.5800.0501
> > TL=0000.0000.0000.0004 TT=0000.0000.0000.0030
> >    TPC=0000.0000.0101.067c TnPC=0000.0000.0101.0680 
> > TSTATE=0000.0000.5800.0501
> > TL=0000.0000.0000.0003 TT=0000.0000.0000.0030
> >    TPC=0000.0000.0101.067c TnPC=0000.0000.0101.0680 
> > TSTATE=0000.0000.5800.0501
> > TL=0000.0000.0000.0002 TT=0000.0000.0000.0030
> >    TPC=0000.0000.0101.067c TnPC=0000.0000.0101.0680 
> > TSTATE=0000.0000.5800.0501
> > TL=0000.0000.0000.0001 TT=0000.0000.0000.0030
> >    TPC=0000.0000.0170.4744 TnPC=0000.0000.0170.4748 
> > TSTATE=0000.0000.1d00.0601
> >

Reply via email to