In Addition, I rebooted the device after installation. Now, I cannot give any input from console. I cannot even enter the bios.
Vertigo Altair <vertigo.alt...@gmail.com>, 4 May 2020 Pzt, 16:15 tarihinde şunu yazdı: > Hello, > I cannot change IRQ in Bios, > In BIOS, com0 settings are like this; > IO = 3F8h (correct) , IRQ = 7 (incorrect) > For installation, I set com0's IRQ to 7 at UKC. And I completed > installation successfully. However, when I try to boot after installation > the console is stucking again. There are 16 character on the last line and > com0 are using to IRQ = 4. At this point, I cannot reach the UKC with "boot > -c". How can I overcome this? > > "Intel X553 SGMII" rev 0x11 at pci10 dev 0 function 0 not configured > "Intel X553 SGMII" rev 0x11 at pci10 dev 0 function 1 not configured > "Intel C3000 ME HECI" rev 0x11 at pci0 dev 24 function 0 not configured > "Intel C3000 UART" rev 0x11 at pci0 dev 26 function 0 not configured > "Intel C3000 UART" rev 0x11 at pci0 dev 26 function 1 not configured > "Intel C3000 UART" rev 0x11 at pci0 dev 26 function 2 not configured > sdhc0 at pci0 dev 28 function 0 "Intel C3000 eMMC" rev 0x11: apic 2 int 16 > sdhc0: SDHC 3.0, 200 MHz base clock > sdmmc0 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma > pcib0 at pci0 dev 31 function 0 "Intel C3000 LPC" rev 0x11 > "Intel C3000 PMC" rev 0x11 at pci0 dev 31 function 2 not configured > "Intel C3000 SMBus" rev 0x11 at pci0 dev 31 function 4 not configured > "Intel C3000 SPI" rev 0x11 at pci0 dev 31 function 5 not configured > isa0 at pcib0 > isadma0 at isa0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > C▒▒+ > сJͅ▒▒▒▒с▒▒ɻ▒▒▒J▒Ł▒▒: ns16550a, 16 byte fifo > pcppi0 at isa0 port 0x61 > spkr0 at pcppi0 > wbsio0 at isa0 port 0x2e/2: NCT6776F rev 0x33 > lm1 at wbsio0 port 0xa10/8: NCT6776F > vmm0 at mainbus0: VMX/EPT > sdmmc0: can't enable card > vscsi0 at root > scsibus2 at vscsi0: 256 targets > softraid0 at root > scsibus3 at softraid0: 256 targets > root on sd0a (1589b7458f9250cf.a) swap on sd0b dump on sd0b > WARNING: / was not properly unmounted > Automatic boot i > > Vertigo Altair <vertigo.alt...@gmail.com>, 3 May 2020 Paz, 17:29 > tarihinde şunu yazdı: > >> Hello Again, >> I have already disabled ACPI at the boot prompt, but the result didn't >> change.Thanks for suggestion.. >> >> Andrea Fleckenstein <afl...@mailbox.org>, 3 May 2020 Paz, 16:41 >> tarihinde şunu yazdı: >> >>> Vertigo Altair <vertigo.alt...@gmail.com> writes: >>> >>> Hello, >>> >>> I had a Dell XPS 8100 with a similar problem and I was able to get >>> around it by disabling ACPI at the boot prompt. Of course, we have very >>> different machines, but it's worth a shot. Unfortunately the boot was >>> extremely slow, on the order of 10min with acpi reenabled, and several >>> minutes >>> without it. Hopefully someone more knowledgeable than me will give a >>> more reasoned answer. Good luck. >>> >>> Best, >>> Andrea >>> >>> > Hi, >>> > I have a Dell VEP 1445 Whitebox, I want to install OpenBSD 6.6. on it. >>> But >>> > When I try to boot, the boot process is stucking. There is no output >>> after >>> > " erase ^?, werase" >>> > >>> > BIOS Boot Selector for VEP1400-X >>> > Version 3.48.0.9-4 >>> > >>> > >>> > POST Configuration >>> > CPU Signature 506F1 >>> > CPU FamilyID=6, Model=5F, SteppingId=1, Processor=0 >>> > Microcode Revision 2E >>> > Platform ID: 0x0 >>> > PMG_CST_CFG_CTL: 0x37 >>> > Misc EN: 0x840089 >>> > Gen PM ConA: 0xA0A00200 >>> > Therm Status: 0x8000000 >>> > POST Control=0xEA000F03, Status=0xE600DF00 >>> > >>> > BIOS initializations... >>> > >>> > CPGC Memtest Channel 0 ...................... PASS >>> > >>> > POST: >>> > RTC Battery OK at last cold boot >>> > RTC date 5/3/2020 9:24:11 >>> > >>> > POST SPD test ............................... PASS >>> > >>> > POST Lower DRAM Memory test ......... >>> > POST ECC Test ............................... PASS >>> > >>> > .... Perf cnt (curr,fixed): 0x32AFD1520,0x8B637FB20 >>> > >>> > POST Lower DRAM Memory test ................. PASS >>> > POST Lower DRAM ECC check ................... PASS >>> > >>> > Current BOOT from Primary BIOS >>> > DxE POST >>> > >>> > POST Upper DRAM Memory test >>> > Short memory cell test >>> > >>> > POST Upper DRAM Memory test ................. PASS >>> > HDD Access .................................. PASS >>> > USB device detected >>> > Temperature test ............................ PASS >>> > FAN controller test ......................... PASS >>> > EEPROM test ................................. PASS >>> > POST PCI test ............................... PASS >>> > POST BMC Interface test ..................... PASS >>> > POST NVRAM check ............................ PASS >>> > POST overall test results ................... PASS >>> > >>> > NVRAM: 00 DF 00 E6 03 0F 00 EA 01 55 3E __ 00 0F 00 F7 >>> > Version 2.19.1266. Copyright (C) 2019 American Megatrends, Inc. >>> > BIOS Date: 06/26/2019 22:19:26 Ver: 0ACHI040 >>> > Press <DEL> or <F2> to enter setup. >>> > probing: pc0 com1 com2 com3 mem[640K 1894M 117M 972K 4M 14336M] >>> > disk: hd0 hd1* hd2* >>> >>> OpenBSD/amd64 BOOTX64 3.46 >>> > boot> stty com0 115200 >>> > boot> set tty com0 >>> > switching console to com0 >>> >>> OpenBSD/amd64 BOOTX64 3.46 >>> > boot> >>> > cannot open hd0a:/etc/random.seed: No such file or directory >>> > booting hd0a:/6.6/amd64/bsd.rd: 3732171+1537024+3885432+0+598016 >>> > [376562+128+455544+303577]=0xa648d0 >>> > entry point at 0x1001000 >>> > Copyright (c) 1982, 1986, 1989, 1991, 1993 >>> > The Regents of the University of California. All rights >>> reserved. >>> > Copyright (c) 1995-2019 OpenBSD. All rights reserved. >>> > https://www.OpenBSD.org <https://www.openbsd.org/> >>> > >>> > OpenBSD 6.6 (RAMDISK_CD) #349: Sat Oct 12 11:03:52 MDT 2019 >>> > dera...@amd64.openbsd.org: >>> /usr/src/sys/arch/amd64/compile/RAMDISK_CD >>> > real mem = 17131601920 (16337MB) >>> > avail mem = 16608419840 (15839MB) >>> > mainbus0 at root >>> > bios0 at mainbus0: SMBIOS rev. 3.0 @ 0x7f1ef000 (55 entries) >>> > bios0: vendor American Megatrends Inc. version "3.48.0.9-4" date >>> 06/26/2019 >>> > bios0: Dell EMC VEP1445-V220 >>> > acpi0 at bios0: ACPI 6.1 >>> > acpi0: tables DSDT FACP FPDT FIDT MCFG APIC BDAT HPET UEFI SSDT DMAR >>> SPCR >>> > TPM2 HEST BERT ERST EINJ WSMT >>> > acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat >>> > cpu0 at mainbus0: apid 0 (boot processor) >>> > cpu0: Intel(R) Atom(TM) CPU C3758 @ 2.20GHz, 2200.40 MHz, 06-5f-01 >>> > cpu0: >>> > >>> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,CX16,xTPR,PDCM,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,3DNOWP,PERF,ITSC,FSGSBASE,TSC_ADJUST,SMEP,ERMS,MPX,RDSEED,SMAP,CLFLUSHOPT,PT,SHA,MD_CLEAR,IBRS,IBPB,STIBP,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES >>> > cpu0: 2MB 64b/line 16-way L2 cache >>> > cpu0: apic clock running at 25MHz >>> > cpu0: mwait min=64, max=64, C-substates=0.2.0.2, IBE >>> > cpu at mainbus0: not configured >>> > cpu at mainbus0: not configured >>> > cpu at mainbus0: not configured >>> > cpu at mainbus0: not configured >>> > cpu at mainbus0: not configured >>> > cpu at mainbus0: not configured >>> > cpu at mainbus0: not configured >>> > ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins >>> > acpiprt0 at acpi0: bus 0 (PCI0) >>> > acpiprt1 at acpi0: bus -1 (PEX0) >>> > acpiprt2 at acpi0: bus -1 (PEX1) >>> > acpiprt3 at acpi0: bus 2 (PEX2) >>> > acpiprt4 at acpi0: bus -1 (PEX3) >>> > acpiprt5 at acpi0: bus -1 (PEX4) >>> > acpiprt6 at acpi0: bus 4 (PEX5) >>> > acpiprt7 at acpi0: bus -1 (PEX6) >>> > acpiprt8 at acpi0: bus -1 (PEX7) >>> > acpiprt9 at acpi0: bus 1 (VRP2) >>> > acpiprt10 at acpi0: bus 5 (VRP0) >>> > acpiprt11 at acpi0: bus 7 (VRP1) >>> > acpicpu at acpi0 not configured >>> > acpitz at acpi0 not configured >>> > "PNP0A08" at acpi0 not configured >>> > "PNP0003" at acpi0 not configured >>> > acpicmos0 at acpi0 >>> > "MVS6190" at acpi0 not configured >>> > "PICB000" at acpi0 not configured >>> > "INTC3000" at acpi0 not configured >>> > "PNP0C33" at acpi0 not configured >>> > "MSFT0101" at acpi0 not configured >>> > pci0 at mainbus0 bus 0 >>> > 0:31:5: mem address conflict 0xfe010000/0x1000 >>> > pchb0 at pci0 dev 0 function 0 "Intel C3000 Host" rev 0x11 >>> > pchb1 at pci0 dev 4 function 0 "Intel C3000 GLREG" rev 0x11 >>> > "Intel C3000 RCEC" rev 0x11 at pci0 dev 5 function 0 not configured >>> > ppb0 at pci0 dev 6 function 0 "Intel C3000 PCIE" rev 0x11 >>> > pci1 at ppb0 bus 1 >>> > "Intel C3000 QAT" rev 0x11 at pci1 dev 0 function 0 not configured >>> > ppb1 at pci0 dev 11 function 0 "Intel C3000 PCIE" rev 0x11 >>> > pci2 at ppb1 bus 2 >>> > em0 at pci2 dev 0 function 0 "Intel I350" rev 0x01: msi, address >>> > 50:9a:4c:ea:96:70 >>> > em1 at pci2 dev 0 function 1 "Intel I350" rev 0x01: msi, address >>> > 50:9a:4c:ea:96:71 >>> > em2 at pci2 dev 0 function 2 "Intel I350" rev 0x01: msi, address >>> > 50:9a:4c:ea:96:72 >>> > em3 at pci2 dev 0 function 3 "Intel I350" rev 0x01: msi, address >>> > 50:9a:4c:ea:96:73 >>> > ppb2 at pci0 dev 15 function 0 "Intel C3000 PCIE" rev 0x11 >>> > pci3 at ppb2 bus 4 >>> > vendor "Atheros", unknown product 0x003c (class network subclass >>> > miscellaneous, rev 0x00) at pci3 dev 0 function 0 not configured >>> > "Intel C3000 SMBus" rev 0x11 at pci0 dev 18 function 0 not configured >>> > ahci0 at pci0 dev 19 function 0 "Intel C3000 AHCI" rev 0x11: msi, AHCI >>> 1.3.1 >>> > ahci0: port 5: 6.0Gb/s >>> > scsibus0 at ahci0: 32 targets >>> > sd0 at scsibus0 targ 5 lun 0: <ATA, 256GB SATA Flash, SFDN> >>> > naa.6611602cbad0d0d0 >>> > sd0: 244198MB, 512 bytes/sector, 500118192 sectors, thin >>> > xhci0 at pci0 dev 21 function 0 "Intel C3000 xHCI" rev 0x11: msi, xHCI >>> 1.0 >>> > usb0 at xhci0: USB revision 3.0 >>> > uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev >>> > 3.00/1.00 addr 1 >>> > ppb3 at pci0 dev 22 function 0 "Intel C3000 PCIE" rev 0x11 >>> > pci4 at ppb3 bus 5 >>> > "Intel X553 SFP+" rev 0x11 at pci4 dev 0 function 0 not configured >>> > "Intel X553 SFP+" rev 0x11 at pci4 dev 0 function 1 not configured >>> > ppb4 at pci0 dev 23 function 0 "Intel C3000 PCIE" rev 0x11 >>> > pci5 at ppb4 bus 7 >>> > "Intel X553 SGMII" rev 0x11 at pci5 dev 0 function 0 not configured >>> > "Intel X553 SGMII" rev 0x11 at pci5 dev 0 function 1 not configured >>> > "Intel C3000 ME HECI" rev 0x11 at pci0 dev 24 function 0 not configured >>> > sdhc0 at pci0 dev 28 function 0 "Intel C3000 eMMC" rev 0x11: apic 2 >>> int 16 >>> > sdhc0: SDHC 3.0, 200 MHz base clock >>> > sdmmc0 at sdhc0: 8-bit, sd high-speed, mmc high-speed, dma >>> > "Intel C3000 LPC" rev 0x11 at pci0 dev 31 function 0 not configured >>> > "Intel C3000 PMC" rev 0x11 at pci0 dev 31 function 2 not configured >>> > "Intel C3000 SMBus" rev 0x11 at pci0 dev 31 function 4 not configured >>> > "Intel C3000 SPI" rev 0x11 at pci0 dev 31 function 5 not configured >>> > isa0 at mainbus0 >>> > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo >>> > com0: console >>> > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo >>> > com2 at isa0 port 0x3e8/8 irq 5: ns16550a, 16 byte fifo >>> > efifb at mainbus0 not configured >>> > umass0 at uhub0 port 1 configuration 1 interface 0 "SanDisk' Cruzer >>> Fit" >>> > rev 2.00/1.00 addr 2 >>> > umass0: using SCSI over Bulk-Only >>> > scsibus1 at umass0: 2 targets, initiator 0 >>> > sd1 at scsibus1 targ 1 lun 0: <SanDisk', Cruzer Fit, 1.00> removable >>> > serial.07815571221118104030 >>> > sd1: 14664MB, 512 bytes/sector, 30031872 sectors >>> > sdmmc0: can't enable card >>> > softraid0 at root >>> > scsibus2 at softraid0: 256 targets >>> > root on rd0a swap on rd0b dump on rd0b >>> > erase ^?, werase >>> >>
