Re: Acer Extensa 5635Z RAM and net boards.

Thu, 31 Dec 2020 02:44:58 -0800 

Hi,
thanks for your reply.
It was a new installation on this notebook so I had to change the SO.
With FreeBSD (11.2) no problem for this interface.
But theconfiguration of the sound cart is a bit difficult.
On OpenBSD was most simple to configure.


Il 30/12/20 23:46, pcost ha scritto:

Ciao Luciano,
I am writing using the same notebook you have, an Acer Extensa 5635, with 4GB Ram. 
My Bios version is 1.3311 and OpenBSD version is 6.8.
Same behavior here: the wifi card works correctly only with one memory card inserted (2GB); inserting the second memory card (2+2GB), the wifi card stops to work. 
The 'dmesg' output is almost the same of yours
(alc0: phy write timeout: phy 0, reg 30) and so on.
I confirm everything works correctly with debian (kernel 5.9).
My workaround is to use a TPLink mini usb wifi network card, that is better than decrease the ram... 
Ciao.


Il 12/20/20 8:08 PM, Isaia Luciano ha scritto:

Hello,
it would seam a OpenBSB problem, the other SO (Linux, FreeBSD) properly activate the interface. 


# sh /etc/netstart alc0
alc0: writev(DHCPDISCOVER): No buffer space available
alc0: writev(DHCPDISCOVER): No buffer space available
alc0: writev(DHCPDISCOVER): No buffer space available
alc0: no lease....alc0: writev(DHCPDISCOVER): No buffer space available
.alc0: writev(DHCPDISCOVER): No buffer space available
.alc0: writev(DHCPDISCOVER): No buffer space avialable
.alc0: writev(DHCPDISCOVER): No buffer space available
.alc0: writev(DHCPDISCOVER): No buffer space available
.alc0: writev(DHCPDISCOVER): No buffer space available
.alc0: writev(DHCPDISCOVER): No buffer space available
sleeping

# ifconfig alc0 down
alc0: could not disable RxQ/TxQ (0xffffffff)!
alc0: could not disable Rx/Tx MAC(0xffffffff)!


I tried with live CD of Sistem Rescue CD and MidnighBSD.
It has already happened to someone.

Thanks.

Luciano.

Il 19/12/20 11:36, luis...@tin.it ha scritto:

  Hi,I have install OpenBSD 6.8 on Acer Laptop with 2GB of RAM.
I have upgrade the memory added a new 2 GB RAM bank.On boot the net interface not running.The dmesg is: 
OpenBSD 6.8 (GENERIC.MP) #98: Sun Oct  4 18:13:26 MDT 2020
dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 4105977856 (3915MB)
avail mem = 3966488576 (3782MB)
random: good seed from bootblocks
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.5 @ 0xb5ec0000 (33 entries)
bios0: vendor Phoenix version "V1.3311" date 12/21/2009
bios0: Acer Extensa 5635Z
acpi0 at bios0: ACPI 3.0
acpi0: sleep states S0 S3 S4 S5
acpi0: tables DSDT FACP HPET MCFG APIC BOOT SSDT SSDT SSDT SSDT
acpi0: wakeup devices USB0(S3) USB1(S3) USBR(S3) EHC1(S3) USB3(S3) EHC2(S3) HDEF(S3) GLAN(S4) 
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpihpet0 at acpi0: 14318179 Hz
acpimcfg0 at acpi0
acpimcfg0: addr 0xe0000000, bus 0-255
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Pentium(R) Dual-Core CPU T4300 @ 2.10GHz, 2095.34 MHz, 06-17-0a
cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,XSAVE,NXE,LONG,LAHF,PERF,SENSOR,MELTDOWN 
cpu0: 1MB 64b/line 4-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 7 var ranges, 88 fixed ranges
cpu0: apic clock running at 199MHz
cpu0: mwait min=64, max=64, C-substates=0.2.2.2, IBE
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Pentium(R) Dual-Core CPU T4300 @ 2.10GHz, 2094.99 MHz, 06-17-0a
cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM,XSAVE,NXE,LONG,LAHF,PERF,SENSOR,MELTDOWN 
cpu1: 1MB 64b/line 4-way L2 cache
cpu1: smt 0, core 1, package 0
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 10 (P0P1)
acpiprt2 at acpi0: bus 2 (RP01)
acpiprt3 at acpi0: bus -1 (RP02)
acpiprt4 at acpi0: bus -1 (RP03)
acpiprt5 at acpi0: bus 7 (RP04)
acpiprt6 at acpi0: bus -1 (RP05)
acpiec0 at acpi0
acpiac0 at acpi0: AC unit online
acpibat0 at acpi0: BAT1 model "AS09C31" serial 9418 type LION oem "SANYO" 
acpibtn0 at acpi0: LID_
acpibtn1 at acpi0: PWRB
acpibtn2 at acpi0: SLPB
"PNP0C14" at acpi0 not configured
acpipci0 at acpi0 PCI0
acpicmos0 at acpi0
"SYN1B20" at acpi0 not configured
"PNP0C14" at acpi0 not configured
acpicpu0 at acpi0: !C3(250@17 mwait.3@0x20), !C2(500@1 mwait.1@0x10), C1(1000@1 mwait.1), PSS acpicpu1 at acpi0: !C3(250@17 mwait.3@0x20), !C2(500@1 mwait.1@0x10), C1(1000@1 mwait.1), PSS 
acpitz0 at acpi0: critical temperature is 108 degC
acpivideo0 at acpi0: VGA_
acpivideo1 at acpi0: GFX0
acpivout0 at acpivideo1: DD02
cpu0: Enhanced SpeedStep 2095 MHz: speeds: 2100, 1600, 1200 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel GM45 Host" rev 0x07
inteldrm0 at pci0 dev 2 function 0 "Intel GM45 Video" rev 0x07
drm0 at inteldrm0
intagp0 at inteldrm0
agp0 at intagp0: aperture at 0xd0000000, size 0x10000000
inteldrm0: apic 2 int 16, GM45, gen 4
"Intel GM45 Video" rev 0x07 at pci0 dev 2 function 1 not configured
uhci0 at pci0 dev 26 function 0 "Intel 82801I USB" rev 0x03: apic 2 int 16 uhci1 at pci0 dev 26 function 1 "Intel 82801I USB" rev 0x03: apic 2 int 21 ehci0 at pci0 dev 26 function 7 "Intel 82801I USB" rev 0x03: apic 2 int 19 
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 configuration 1 interface 0 "Intel EHCI root hub" rev 2.00/1.00 addr 1 
azalia0 at pci0 dev 27 function 0 "Intel 82801I HD Audio" rev 0x03: msi
azalia0: codecs: Conexant CX20561
audio0 at azalia0
ppb0 at pci0 dev 28 function 0 "Intel 82801I PCIE" rev 0x03: msi
pci1 at ppb0 bus 2
ppb1 at pci0 dev 28 function 3 "Intel 82801I PCIE" rev 0x03: msi
pci2 at ppb1 bus 7
athn0 at pci2 dev 0 function 0 "Atheros AR9281" rev 0x01: apic 2 int 19
athn0: could not reset chip
ppb2 at pci0 dev 28 function 5 "Intel 82801I PCIE" rev 0x03: msi
pci3 at ppb2 bus 9
alc0 at pci3 dev 0 function 0 "Attansic Technology L1C" rev 0xc0: msialc0: phy write timeout: phy 0, reg 29 
alc0: phy write timeout: phy 0, reg 30
alc0: phy write timeout: phy 0, reg 29
alc0: phy write timeout: phy 0, reg 30
alc0: phy write timeout: phy 0, reg 29
alc0: phy write timeout: phy 0, reg 30
alc0: phy write timeout: phy 0, reg 29
alc0: phy write timeout: phy 0, reg 30
alc0: phy write timeout: phy 0, reg 29
alc0: phy write timeout: phy 0, reg 30
alc0: phy write timeout: phy 0, reg 29
alc0: phy write timeout: phy 0, reg 30
alc0: phy write timeout: phy 0, reg 29
alc0: phy read timeout: phy 0, reg 30
alc0: phy write timeout: phy 0, reg 30
alc0: phy write timeout: phy 0, reg 29
alc0: phy read timeout: phy 0, reg 30
alc0: phy write timeout: phy 0, reg 30
alc0: could not disable RxQ/TxQ (0xffffffff)!
alc0: could not disable Rx/Tx MAC(0xffffffff)!
alc0: master reset timeout!
alc0: reset timeout(0xffffffff)!
alc0: reloading EEPROM timeout!
, address ff:ff:ff:ff:ff:ff
alc0: phy read timeout: phy 0, reg 1
alc0: no PHY found!
uhci2 at pci0 dev 29 function 0 "Intel 82801I USB" rev 0x03: apic 2 int 23 uhci3 at pci0 dev 29 function 1 "Intel 82801I USB" rev 0x03: apic 2 int 19 uhci4 at pci0 dev 29 function 2 "Intel 82801I USB" rev 0x03: apic 2 int 18 uhci5 at pci0 dev 29 function 3 "Intel 82801I USB" rev 0x03: apic 2 int 16 ehci1 at pci0 dev 29 function 7 "Intel 82801I USB" rev 0x03: apic 2 int 23 
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 configuration 1 interface 0 "Intel EHCI root hub" rev 2.00/1.00 addr 1 
ppb3 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0x93
pci4 at ppb3 bus 10
pcib0 at pci0 dev 31 function 0 "Intel 82801IBM LPC" rev 0x03
ahci0 at pci0 dev 31 function 2 "Intel 82801I AHCI" rev 0x03: msi, AHCI 1.2 
ahci0: port 0: 3.0Gb/s
ahci0: port 1: 1.5Gb/s
ahci0: PHY offline on port 4
ahci0: PHY offline on port 5
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <ATA, CT120BX500SSD1, M6C> naa.0000000000000000 
sd0: 114473MB, 512 bytes/sector, 234441648 sectors, thin
cd0 at scsibus1 targ 1 lun 0: <TSSTcorp, CDDVDW TS-L633C, AC01> removable ichiic0 at pci0 dev 31 function 3 "Intel 82801I SMBus" rev 0x03: apic 2 int 19 
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 2GB DDR3 SDRAM PC3-8500 SO-DIMM
spdmem1 at iic0 addr 0x52: 2GB DDR3 SDRAM PC3-8500 SO-DIMM
usb2 at uhci0: USB revision 1.0
uhub2 at usb2 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00 addr 1 
usb3 at uhci1: USB revision 1.0
uhub3 at usb3 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00 addr 1 
usb4 at uhci2: USB revision 1.0
uhub4 at usb4 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00 addr 1 
usb5 at uhci3: USB revision 1.0
uhub5 at usb5 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00 addr 1 
usb6 at uhci4: USB revision 1.0
uhub6 at usb6 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00 addr 1 
usb7 at uhci5: USB revision 1.0
uhub7 at usb7 configuration 1 interface 0 "Intel UHCI root hub" rev 1.00/1.00 addr 1 
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0: console keyboard
pms0 at pckbc0 (aux slot)
wsmouse0 at pms0 mux 0
pms0: Synaptics touchpad, firmware 7.2, 0x1c0b1 0xa44000 0x0 0xd04731 0xa0000 
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
uvideo0 at uhub1 port 8 configuration 1 interface 0 "SuYin Video WebCam" rev 2.00/5.00 addr 2 
video0 at uvideo0
uhidev0 at uhub4 port 1 configuration 1 interface 0 "2.4G 2.4G Wireless Device" rev 1.10/10.01 addr 2 
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 variable keys, 6 key codes
wskbd1 at ukbd0 mux 1
uhidev1 at uhub4 port 1 configuration 1 interface 1 "2.4G 2.4G Wireless Device" rev 1.10/10.01 addr 2 
uhidev1: iclass 3/1, 186 report ids
ums0 at uhidev1 reportid 1: 5 buttons, Z and W dir
wsmouse1 at ums0 mux 0
uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
uhid1 at uhidev1 reportid 3: input=2, output=0, feature=0
uhid2 at uhidev1 reportid 4: input=1, output=0, feature=0
uhid3 at uhidev1 reportid 186: input=31, output=31, feature=0
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
sd1 at scsibus3 targ 1 lun 0: <OPENBSD, SR CRYPTO, 006>
sd1: 114470MB, 512 bytes/sector, 234435953 sectors
root on sd1a (fc79adbb28d62767.a) swap on sd1b dump on sd1b
inteldrm0: 1366x768, 32bpp
wsdisplay0 at inteldrm0 mux 1: console (std, vt100 emulation), using wskbd0 
wskbd1: connecting to wsdisplay0
wsdisplay0: screen 1-5 added (std, vt100 emulation)
alc0: could not disable RxQ/TxQ (0xffffffff)!
alc0: could not disable Rx/Tx MAC(0xffffffff)!
alc0: master reset timeout!
alc0: reset timeout(0xffffffff)!

The net is not accessible.If I remove the bank the net is OK.

Why?Any idea?
Thanks.
Luciano.

Reply via email to