People have been asking me about env settings to boot a R12k.
Here comes everything you need, and now it will be found in the
archives by anyone.
--
/Bachman
---------------------------------------------------------------
Logs which worked with my R12k are shared without any guarantees.
/bkw
bahkha AT gmail DOT com
### TO BOOT INSTALL CDROM ###
printenv
AutoLoad=Yes
diskless=0
dbaud=9600
volume=80
sgilogo=y
monitor=h
TimeZone=PST8PDT
netaddr=192.0.2.1
crt_option=1
SystemPartition=pci(0)scsi(0)disk(2)rdisk(0)partition(8)
OSLoadPartition=pci(0)scsi(0)disk(2)rdisk(0)partition(0)
OSLoader=boot
OSLoadOptions=auto
console=d
ConsoleOut=serial(0)
ConsoleIn=serial(0)
cpufreq=270
eaddr=08:00:69:0e:9b:ab
videostatus=illegal_env_var
OSLoadFilename=/bsd.rd
### WHEN INSTALLATION FINNISHED SUCCESSFULLY, MAKE SURE THE
ENVIRONMENT SETTINGS ARE AS BELOW ###
Cannot connect to keyboard -- check the cable.
Cannot open keyboard() for input
Cannot connect to keyboard -- check the cable.
Cannot open keyboard() for input
Running power-on diagnostics...
System Maintenance Menu
1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor
Option? 1
Starting up the system...
arg 0: pci(0)scsi(0)disk(2)rdisk(0)partition(8)/boot
arg 1: OSLoadOptions=auto
arg 2: ConsoleIn=serial(0)
arg 3: ConsoleOut=serial(0)
arg 4: SystemPartition=pci(0)scsi(0)disk(2)rdisk(0)partition(8)
arg 5: OSLoader=boot
arg 6: OSLoadPartition=pci(0)scsi(0)disk(2)rdisk(0)partition(0)
arg 7: OSLoadFilename=/bsd
OpenBSD/sgi Arcbios boot
Boot: pci(0)scsi(0)disk(2)rdisk(0)partition(0)/bsd
|/-\|Loading ELF64 file
0xffffffff80100000:0x310c40,
/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-Zero
0xffffffff80410c40:0x5bb80, Loading symbol tab
le
\|/-\|/-\|/-\|/-\|Start at 0xffffffff80100000
ARCS32 Firmware Version 1.10
SR=34050080
Found SGI-IP32, setting up.
Initial setup done, switching console.
NOTE: TLB code too large, using trampolines
[ using 267936 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2005 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 3.8 (GENERIC) #164: Sat Sep 10 17:10:35 MDT 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/sgi/compile/GENERIC
real mem = 268435456
rsvd mem = 7020544
avail mem = 228618240
using 3276 buffers containing 13418496 bytes of memory
mainbus0 (root)
cpu0 at mainbus0: MIPS R12000 CPU rev 2.3 270 MHz with R10000 FPU rev 0.0
cpu0: cache L1-I 32KB D 32KB 2 way, L2 1024KB 2 way
macebus0 at mainbus0: crime rev 10.1
clock0 at macebus0: TOD with DS1687, ticker on int5 using count register
macepcibr0 at macebus0: mace rev 1, host system O2
pci0 at macepcibr0 bus 0
ahc0 at pci0 dev 1 function 0 "Adaptec AIC-7880" rev 0x00: irq 9
ahc0: Host Adapter Bios disabled. Using default SCSI device parameters
scsibus0 at ahc0: 16 targets
sd0 at scsibus0 targ 2 lun 0: <SGI, IBM DNES-309170Y, SA30> SCSI3 0/direct fixed
sd0: 8682MB, 11474 cyl, 5 head, 309 sec, 512 bytes/sec, 17781520 sec total
cd0 at scsibus0 targ 4 lun 0: <TOSHIBA, CD-ROM XM-6201TA, 1037> SCSI2 5/cdrom re
movable
ahc1 at pci0 dev 2 function 0 "Adaptec AIC-7880" rev 0x00: irq 10
ahc1: Host Adapter Bios disabled. Using default SCSI device parameters
scsibus1 at ahc1: 16 targets
com0 at macebus0: ns16550a, 16 byte fifo
com0: console
com1 at macebus0: ns16550a, 16 byte fifo
mec0 at macebus0: MAC-110 rev 1, address 08:00:69:0e:9b:ab
nsphy0 at mec0 phy 8: DP83840 10/100 PHY, rev. 1
mavb0 at macebus0: AD1843 rev 1
audio0 at mavb0
boot device: sd0.
root on sd0a
ahc0: target 2 using 16bit transfers
ahc0: target 2 synchronous at 10.0MHz, offset = 0x8
rootdev=0x0 rrootdev=0x900 rawdev=0x902
Automatic boot in progress: starting file system checks.
/dev/rsd0a: file system is clean; not checking
/dev/rsd0h: file system is clean; not checking
/dev/rsd0d: file system is clean; not checking
/dev/rsd0g: file system is clean; not checking
/dev/rsd0e: file system is clean; not checking
setting tty flags
starting network
DHCPREQUEST on mec0 to 255.255.255.255 port 67
DHCPACK from 192.168.1.1
bound to 192.168.1.6 -- renewal in 21600 seconds.
starting system logger
starting rpc daemons:.
savecore: no core dump
checking quotas: done.
building ps databases: kvm dev.
clearing /tmp
starting pre-securelevel daemons:.
setting kernel security level: kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files
starting network daemons: sendmail inetd sshd.
starting local daemons:.
standard daemons: cron.
Fri May 19 18:08:58 CEST 2006
OpenBSD/sgi (silikon) (tty00)
login:
