On Sat, Jun 17, 2006 at 01:41:27AM +0000, Travers Buda wrote:
> Looks like a crappy bios (pardon the redundancy,) try
>
> boot> boot -c
>
> UKC > disable pcibios
> UKC > quit
I tried your suggestion, as well as:
change pcibios
1,2,20
disable ppb
On both bsd & bsd.mp to no effect.
I flashed the bois to the lastest firmware, and tried the above again,
no good.
The only way I could get it to boot was with:
boot hd0a:/bsd.rd -a
and set the root device to wd0a.
Thanks for the help, dmesg from bsd.rd below:
OpenBSD 3.9 (RAMDISK_CD) #1025: Thu Mar 2 02:43:29 MST 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
cpu0: Intel Pentium III ("GenuineIntel" 686-class, 128KB L2 cache) 635 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
real mem = 199729152 (195048K)
avail mem = 176427008 (172292K)
using 2463 buffers containing 10088448 bytes (9852K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 01/15/99, BIOS32 rev. 0 @ 0xfdb70
apm0 at bios0: Power Management spec V1.2
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI BIOS has 9 Interrupt Routing table entries
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801AA LPC" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x8000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82810E" rev 0x03: rng active, 8Kb/sec
vga1 at pci0 dev 1 function 0 "Intel 82810E Graphics" rev 0x03
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
ppb0 at pci0 dev 30 function 0 "Intel 82801AA Hub-to-PCI" rev 0x02
pci1 at ppb0 bus 1
rl0 at pci1 dev 0 function 0 "Realtek 8139" rev 0x10: irq 11, address
00:90:47:05:99:6d
rlphy0 at rl0 phy 0: RTL internal PHY
ichpcib0 at pci0 dev 31 function 0 "Intel 82801AA LPC" rev 0x02
pciide0 at pci0 dev 31 function 1 "Intel 82801AA IDE" rev 0x02: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <Maxtor 6Y080P0>
wd0: 16-sector PIO, LBA, 78167MB, 160086528 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TEAC, DV-516D, 1.06> SCSI0 5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
uhci0 at pci0 dev 31 function 2 "Intel 82801AA USB" rev 0x02: irq 5
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
"Intel 82801AA SMBus" rev 0x02 at pci0 dev 31 function 3 not configured
"Intel 82801AA AC97" rev 0x02 at pci0 dev 31 function 5 not configured
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask f7e5 netmask ffe5 ttymask ffe7
rd0: fixed, 3800 blocks
uhidev0 at uhub0 port 1 configuration 1 interface 0
uhidev0: Logitech Optical USB Mouse, rev 2.00/3.40, addr 2, iclass 3/1
uhid at uhidev0 not configured
dkcsum: wd0 matches BIOS drive 0x80
root device? wd0a
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
> > I've just installed 3.9 RELEASE on an i386 and got a kernel page
> > fault.
> >
> > Booted the box from the floppy39.fs, sliced the disk, installed some
> > sets & rebooted, as per normal.
> >
> > [ using 493460 bytes of bsd ELF symbol table ]
> > Copyright (c) 1982, 1986, 1989, 1991, 1993
> > The Regents of the University of California. All rights
> > reserved. Copyright (c) 1995-2006 OpenBSD. All rights reserved.
> > http://www.OpenBSD.org
> >
> > OpenBSD 3.9 (GENERIC) #617: Thu Mar 2 02:26:48 MST 2006
> > [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
> > cpu0: Intel Pentium III ("GenuineIntel" 686-class, 128KB L2 cache)
> > 635 MHz cpu0:
> > FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE=
> > 36,MMX,FXSR,SSE real mem =3D 199729152 (195048K)
> > avail mem =3D 175271936 (171164K)
> > using 2463 buffers containing 10088448 bytes (9852K) of memory
> > mainbus0 (root)
> > bios0 at mainbus0: AT/286+(00) BIOS, date 01/15/99, BIOS32 rev. 0 @
> > 0xfdb70 apm0 at bios0: Power Management spec V1.2
> > apm0: AC on, battery charge unknown
> > apm0: flags 30102 dobusy 0 doidle 1
> > pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
> > pcibios0: PCI BIOS has 9 Interrupt Routing table entries
> > pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82801AA LPC" rev
> > 0x00) pcibios0: PCI bus #1 is the last bus
> > bios0: ROM list: 0xc0000/0x8000
> > uvm_fault(0xd05c2f60, 0xdeeb8000, 0, 1) -> e
> > kernel: page fault trap, code=3D0
> > Stopped at scan_smbios+0xb9: cmpb $0,0(%ebx)
> > ddb
