This is a net4801-50 with a 1G SanDisk Ultra II...
The system booted but did get DMA errors on the "disk"
any Ideas?
(this is not a GENERIC kernel but one based on the flashdist settings)
comBIOS ver. 1.28 20050529 Copyright (C) 2000-2005 Soekris Engineering.
net4801
0128 Mbyte Memory CPU Geode 266 Mhz
Pri Mas SanDisk SDCFH-1024 LBA Xlt 993-32-63 1001 Mbyte
Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int
-------------------------------------------------------------------
0:00:0 1078 0001 06000000 0107 0280 00 00 00 00000000 00000000
0:06:0 100B 0020 02000000 0107 0290 00 3F 00 0000E101 A0000000 10
0:07:0 100B 0020 02000000 0107 0290 00 3F 00 0000E201 A0001000 10
0:08:0 100B 0020 02000000 0107 0290 00 3F 00 0000E301 A0002000 10
0:18:2 100B 0502 01018001 0005 0280 00 00 00 00000000 00000000
0:19:0 0E11 A0F8 0C031008 0117 0280 08 38 00 A0003000 00000000 11
1 Seconds to automatic boot. Press Ctrl-P for entering Monitor.
Using drive 0, partition 3.
Loading.....
probing: pc0 com0 com1 pci mem[639K 127M a20=on]
disk: hd0+
>> OpenBSD/i386 BOOT 2.10
switching console to com0
>> OpenBSD/i386 BOOT 2.10
com0: 9600 baud
boot>
booting hd0a:/bsd: 2398616+268216 [52+126672+114163]=0x2c5fbc
entry point at 0x200120
[ using 241260 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2006 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 4.0 (DroidOS) #5: Sun Sep 17 16:00:48 PDT 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/DroidOS
cpu0: Geode(TM) Integrated Processor by National Semi ("Geode by NSC"
586-class) 267 MHz
cpu0: FPU,TSC,MSR,CX8,CMOV,MMX
cpu0: TSC disabled
real mem = 133787648 (130652K)
avail mem = 118575104 (115796K)
using 1658 buffers containing 6791168 bytes (6632K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 20/50/29, BIOS32 rev. 0 @ 0xf7840
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0x9000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00
sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq
10, address 00:00:24:c1:c8:60
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq
10, address 00:00:24:c1:c8:61
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq
10, address 00:00:24:c1:c8:62
nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1
gscpcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00
gpio0 at gscpcib0: 64 pins
"NS SC1100 SMI" rev 0x00 at pci0 dev 18 function 1 not configured
pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFH-1024>
wd0: 4-sector PIO, LBA, 977MB, 2001888 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev 0x00: iid 6
revision 3 wdstatus 0
ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq 11,
version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Compaq OHCI root hub, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
isa0 at gscpcib0
isadma0 at isa0
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
gpio1 at nsclpcsio0: 29 pins
gscsio0 at isa0 port 0x15c/2: SC1100 SIO rev 1:
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
biomask fbe7 netmask ffe7 ttymask ffe7
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
wd0(pciide0:0:0): timeout
type: ata
c_bcount: 8192
c_skip: 0
pciide0:0:0: bus-master DMA error: missing interrupt, status=0x21
wd0a: device timeout reading fsbn 128 of 128-143 (wd0 bn 191; cn 0 tn 3 sn
2), retrying
wd0(pciide0:0:0): timeout
type: ata
c_bcount: 8192
c_skip: 0
pciide0:0:0: bus-master DMA error: missing interrupt, status=0x21
wd0: transfer error, downgrading to PIO mode 4
wd0(pciide0:0:0): using PIO mode 4
wd0a: device timeout reading fsbn 128 of 128-143 (wd0 bn 191; cn 0 tn 3 sn
2), retrying
wd0: soft error (corrected)
/dev/rwd0a: file system is clean; not checking
mfs: mounting /tmp...
Warning: inode blocks/cyl group (12) >= data blocks (8) in last
cylinder group. This implies 256 sector(s) cannot be allocated.
mfs: populating /tmp...
databases: dev
securelevel: kern.securelevel: 0 -> 1
watchdog: kern.watchdog.period: 0 -> 32
watchdog: kern.watchdog.auto: 1 -> 1
ip forwarding:net.inet.ip.forwarding: 0 -> 1
hostname: setting hostname to ecotopia...
inet: configuring IP on system interfaces...
route: adding default route...
add net default: gateway 66.92.185.1
pf/nat: configuring and enabling...
pf enabled
syslogd: starting log daemon...
starting DNS: named
ssh: starting daemon...
OpenBSD/i386 (ecotopia) (tty00)
login:
