I've got a "Cisco" Atheros card, it shows up in dmesg as:
ath0 at cardbus1 dev 0 function 0 "Atheros Communications, Inc.,
AR5001-0000-0000, Wireless LAN Reference Card": irq 11
ath0: AR5213 5.6 phy 4.1 rf5112 3.6, FCC1A, address 00:40:96:a1:49:3c
I can associate and connect to a Linksys AP (802.11b) without WEP, but
when I try to connect to an OpenBSD AP (802.11g, AP has a ral card) I
get "ath0: bogus xmit rate 0x0 (idx 0x7)" and "ath0: unable to reset
hardware; hal status 3819281708". I've tried both 3.9 and -current.
Full dmesg below. Is this a configuration issue, or is something broken
with this card?
hostname.ath0:
dhcp NONE NONE NONE nwid cerberusG nwkey 0xsomething
OpenBSD 4.0 (GENERIC) #1107: Sat Sep 16 19:15:58 MDT 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel(R) Pentium(R) 4 Mobile CPU 1.70GHz ("GenuineIntel"
686-class) 1.70 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM
real mem = 267415552 (261148K)
avail mem = 236179456 (230644K)
using 3289 buffers containing 13471744 bytes (13156K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(f5) BIOS, date 07/08/03, BIOS32 rev. 0 @
0xfd7e0, SMBIOS rev. 2.31 @ 0xe0010 (50 entries)
bios0: IBM 2653H6U
apm0 at bios0: Power Management spec V1.2
apm0: battery life expectancy 94%
apm0: AC on, battery charge high
apm0: flags 30102 dobusy 0 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xfd770/0x890
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdeb0/256 (14 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev 0x00)
pcibios0: PCI bus #6 is the last bus
bios0: ROM list: 0xc0000/0x10000 0xd0000/0x1000 0xd1000/0x1000
0xdc000/0x4000! 0xe0000/0x10000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82845 Host" rev 0x04
ppb0 at pci0 dev 1 function 0 "Intel 82845 AGP" rev 0x04
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 vendor "ATI", unknown product 0x4c58 rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
uhci0 at pci0 dev 29 function 0 "Intel 82801CA/CAM USB" rev 0x02: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1 "Intel 82801CA/CAM USB" rev 0x02: irq 11
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2 "Intel 82801CA/CAM USB" rev 0x02: irq 11
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ppb1 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0x42
pci2 at ppb1 bus 2
cbb0 at pci2 dev 0 function 0 "Ricoh 5C476 CardBus" rev 0xa8: irq 11
cbb1 at pci2 dev 0 function 1 "Ricoh 5C476 CardBus" rev 0xa8: irq 11
"Ricoh 5C552 Firewire" rev 0x00 at pci2 dev 0 function 2 not configured
wi0 at pci2 dev 2 function 0 "Intersil PRISM2.5" rev 0x01: irq 11
wi0: PRISM2.5 ISL3874A(Mini-PCI) (0x8013), Firmware 1.0.7 (primary),
1.3.6 (station), address 00:20:e0:8c:07:9f
fxp0 at pci2 dev 8 function 0 "Intel PRO/100 VE" rev 0x42, i82562: irq
11, address 00:d0:59:c0:16:30
inphy0 at fxp0 phy 1: i82562ET 10/100 PHY, rev. 0
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 3 device 0 cacheline 0x0, lattimer 0xb0
pcmcia0 at cardslot0
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 6 device 0 cacheline 0x0, lattimer 0xb0
pcmcia1 at cardslot1
ichpcib0 at pci0 dev 31 function 0 "Intel 82801CAM LPC" rev 0x02: SpeedStep
pciide0 at pci0 dev 31 function 1 "Intel 82801CAM IDE" rev 0x02: DMA,
channel 0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <IC25T060ATCS05-0>
wd0: 16-sector PIO, LBA, 57231MB, 117210240 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <MATSHITA, DVD-ROM SR-8177, NB21> SCSI0
5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
ichiic0 at pci0 dev 31 function 3 "Intel 82801CA/CAM SMBus" rev 0x02: irq 11
iic0 at ichiic0
auich0 at pci0 dev 31 function 5 "Intel 82801CA/CAM AC97" rev 0x02: irq
11, ICH3 AC97
ac97: codec id 0x41445348 (Analog Devices AD1881A)
ac97: codec features headphone, Analog Devices Phat Stereo
audio0 at auich0
"Intel 82801CA/CAM Modem" rev 0x02 at pci0 dev 31 function 6 not configured
isa0 at ichpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt2 at isa0 port 0x3bc/4: polled
npx0 at isa0 port 0xf0/16: using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
biomask effd netmask effd ttymask ffff
pctr: user-level cycle counter enabled
ath0 at cardbus1 dev 0 function 0 "Atheros Communications, Inc.,
AR5001-0000-0000, Wireless LAN Reference Card": irq 11
ath0: AR5213 5.6 phy 4.1 rf5112a 3.6, FCC1A, address 00:40:96:a1:49:3c
uaudio0 at uhub1 port 2 configuration 1 interface 0: XITEL MD-PORT DG2,
rev 1.00/1.00, addr 2
uaudio0: ignored setting with precision 20
uaudio0: ignored setting with precision 20
uaudio0: audio rev 1.00, 4 mixer controls
audio1 at uaudio0
uhidev0 at uhub1 port 2 configuration 1 interface 2
uhidev0: XITEL MD-PORT DG2, rev 1.00/1.00, addr 2, iclass 3/0
uhid0 at uhidev0: input=1, output=1, feature=0
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
