Dear All,
I have a problem with Intel D102GGC2 board and DLink 580TX card, where
it did not detect the DLink 4 ports 10/100 ethernet on OpenBSD 4.0.
OpenBSD 4.0 only detect two ports ste2 and ste3.
I am wondering if it is the problem with detecting IRQ, It stated IRQ 11. Where
on Windows the Intel motherboard D102GGC2 could detect the DLink 4 ports,
with different IRQ.
Thanks and best regards,
Riwan
Attached is the dmesg:
OpenBSD 4.0 (GENERIC) #1107: Sat Sep 16 19:15:58 MDT 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
RTC BIOS diagnostic error 80<clock_battery>
cpu0: Intel(R) Pentium(R) 4 CPU 3.20GHz ("GenuineIntel" 686-class) 3.21 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,CNXT-ID,CX16
real mem = 937385984 (915416K)
avail mem = 846831616 (826984K)
using 4256 buffers containing 46972928 bytes (45872K) of memory
RTC BIOS diagnostic error 80<clock_battery>
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 05/02/06, SMBIOS rev. 2.4 @
0xe4cd0 (29 entries)
bios0: Intel Corporation D102GGC2
apm0 at bios0: Power Management spec V1.2
apm0: battery life expectancy 0%
apm0: AC off, battery charge unknown, estimated 0:00 hours
apm0: flags 30102 dobusy 0 doidle 1
pcibios at bios0 function 0x1a not configured
bios0: ROM list: 0xc0000/0xc000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 vendor "ATI", unknown product 0x5a33 rev 0x01
ppb0 at pci0 dev 1 function 0 "ATI RS480 PCIE" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 5 function 0 "ATI Radeon XPRESS 200" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pciide0 at pci0 dev 17 function 0 "ATI IXP400 SATA" rev 0x80: DMA
pciide0: using irq 10 for native-PCI interrupt
pciide1 at pci0 dev 18 function 0 "ATI IXP400 SATA" rev 0x80: DMA
pciide1: using irq 11 for native-PCI interrupt
piixpm0 at pci0 dev 20 function 0 "ATI IXP400 SMBus" rev 0x81: SMI
iic0 at piixpm0
adt0 at iic0 addr 0x2e: sch5017 rev 0x8a
pciide2 at pci0 dev 20 function 1 "ATI IXP400 IDE" rev 0x80: DMA, channel 0
configured to compatibility, channel 1 configured to compatibility
wd0 at pciide2 channel 0 drive 0: <ST3802110A>
wd0: 16-sector PIO, LBA48, 76319MB, 156301488 sectors
wd0(pciide2:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5
pcib0 at pci0 dev 20 function 3 "ATI IXP400 ISA" rev 0x80
ppb1 at pci0 dev 20 function 4 "ATI IXP400 PCI" rev 0x80
pci2 at ppb1 bus 2
rl0 at pci2 dev 2 function 0 "Realtek 8139" rev 0x10: irq 11, address
00:19:d1:0f:e3:b1
rlphy0 at rl0 phy 0: RTL internal PHY
ppb2 at pci2 dev 3 function 0 "Intel S21152BB PCI-PCI" rev 0x00
pci3 at ppb2 bus 3
ste0 at pci3 dev 4 function 0 "D-Link Systems 550TX" rev 0x15: irq 11ste0:
global reset never completed
ste0: eeprom failed to come ready
: failed to read station address
ste1 at pci3 dev 5 function 0 "D-Link Systems 550TX" rev 0x15: irq 11ste1:
global reset never completed
ste1: eeprom failed to come ready
: failed to read station address
ste2 at pci3 dev 6 function 0 "D-Link Systems 550TX" rev 0x15: irq 11,
address 00:0d:88:68:88:4a
ukphy0 at ste2 phy 1: Generic IEEE 802.3u media interface, rev. 0: OUI
0x0090c3, model 0x0004
ste3 at pci3 dev 7 function 0 "D-Link Systems 550TX" rev 0x15: irq 11,
address 00:0d:88:68:88:4b
ukphy1 at ste3 phy 1: Generic IEEE 802.3u media interface, rev. 0: OUI
0x0090c3, model 0x0004
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
biomask ffed netmask ffed ttymask ffef
pctr: user-level cycle counter enabled
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
