Hi
Two (unrelated) problems with the axe device:
1. Is altq/pf not implemented for USB-Ethernet devices like axe0 ?
I can't get the axe0 device to work with queuing rules of pf:
Device according to dmesg (full dmesg see end of email):
axe0 at uhub0 port 1 configuration 1 interface 0
axe0: Cisco-Linksys USB200M v2, rev 2.00/0.01, addr 2, AX88772, address
00:10:60:06:5e:4d
ukphy0 at axe0 phy 16: Generic IEEE 802.3u media interface, rev. 1: OUI
0x000ec6, model 0x0001
pf.conf part which makes the device unsuable (no packet will flow through
anymore)
# variable substitutions
internal=axe0
external=gem0
local_net = "192.168.100.0/23"
voip_ports = "{ 5060, 5061 , 9999 >< 20001 }"
voip_tcp = "{ 5060 5061 }"
voip_server = "{ xxx.yyy.200.79 xxx.yyy.200.80 xxx.yyy.200.81
xxx.yyy.200.148 }"
altq on $internal cbq bandwidth 3Mb queue { std_in, voip_in, dns_in }
queue std_in bandwidth 2.6Mb cbq(default)
queue voip_in bandwidth 220Kb priority 4
queue dns_in bandwidth 120Kb priority 5
pass out on $internal proto { tcp udp } from any port domain to
$local_net queue dns_in
pass out on $internal proto tcp from any port $voip_tcp to
$local_net queue(std_in, voip_in)
pass out on $internal proto udp from any port $voip_ports
to $local_net queue voip_in
pass out on $internal proto udp from $voip_server to
$local_net port 9999 >< 20001 queue voip_in
queuing on the gem0 device works fine (rules ommited here)
The same pf.conf was actice and nicely working on a different (meanwhile
dead ) machine with rl0 and rl1 IFs
2. after some time the axe0 device gets into a error state (as if
detached, but it isn't):
axe0: usb errors on rx: IOERROR
axe0: usb errors on rx: IOERROR
axe0: at uhub0 port 1 (addr 2) disconnected
ukphy0 detached
axe0 detached
axe0 at uhub0 port 1 configuration 1 interface 0
axe0: Cisco-Linksys USB200M v2, rev 2.00/0.01, addr 2, AX88772, address
00:10:60:06:5e:4d
ukphy0 at axe0 phy 16: Generic IEEE 802.3u media interface, rev. 1: OUI
0x000ec6, model 0x0001
What could cause this? (detaching it by hand doesn't invole the IOERROR
message...)
Greetings & thanks
cmb
complete dmesg, kernel compiled by me, as all generic kernel since 3.3
hang on the (non-existant) second USB1.1 device
OpenBSD 4.0 (GENERIC.new) #0: Fri Nov 17 01:52:41 CET 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/macppc/compile/GENERIC.new
real mem = 167772160 (163840K)
avail mem = 142712832 (139368K)
using 1254 buffers containing 8388608 bytes (8192K) of memory
mainbus0 (root): model PowerBook2,1
cpu0 at mainbus0: 750 (Revision 0x8300): 299 MHz: 512KB backside cache
memc0 at mainbus0: uni-n
ki2c0 at memc0 offset 0xf8001000: cannot get i2c-rate
mpcpcibr0 at mainbus0 pci: uni-north, Revision 0xff
pci0 at mpcpcibr0 bus 0
pchb0 at pci0 dev 11 function 0 "Apple Uni-N AGP" rev 0x00
vgafb0 at pci0 dev 16 function 0 "ATI Mach64 LN" rev 0x64, mmio
wsdisplay0 at vgafb0 mux 1: console (std, vt100 emulation)
mpcpcibr1 at mainbus0 pci: uni-north, Revision 0x0
pci1 at mpcpcibr1 bus 0
pchb1 at pci1 dev 11 function 0 "Apple Uni-N" rev 0x00
macobio0 at pci1 dev 23 function 0 "Apple Keylargo" rev 0x02
openpic0 at macobio0 offset 0x40000: version 0x4614
macgpio0 at macobio0 offset 0x50
macgpio1 at macgpio0 irq 47
"programmer-switch" at macgpio0 not configured
"extint-gpio12" at macgpio0 not configured
daca0 at macobio0 offset 0x10000: irq 30,1,2
"escc-legacy" at macobio0 offset 0x12000 not configured
zsc0 at macobio0 offset 0x13000: irq 22,50
zstty0 at zsc0 channel 0
zstty1 at zsc0 channel 1
"timer" at macobio0 offset 0x15000 not configured
adb0 at macobio0 offset 0x16000 irq 25: via-pmu, 3 targets
akbd0 at adb0 addr 2: PowerBook G4 keyboard (Inverted T)
wskbd0 at akbd0: console keyboard, using wsdisplay0
ams0 at adb0 addr 3: EMP trackpad <tpad> 2-button, 400 dpi
wsmouse0 at ams0 mux 0
abtn0 at adb0 addr 7: brightness/volume/eject buttons
apm0 at adb0: battery flags 0x5, 100% charged
"battery" at macobio0 offset 0x0 not configured
"backlight" at macobio0 offset 0xf300 not configured
ki2c1 at macobio0 offset 0x18000
iic0 at ki2c1
wdc0 at macobio0 offset 0x1f000 irq 19: DMA
wd0 at wdc0 channel 0 drive 0: <TOSHIBA MK3211MAT>
wd0: 16-sector PIO, LBA, 3102MB, 6354432 sectors
wd0(wdc0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2
wdc1 at macobio0 offset 0x20000 irq 20: DMA
atapiscsi0 at wdc1 channel 0 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <MATSHITA, CD-ROM CR-175, 5AAE> SCSI0
5/cdrom removable
cd0(wdc1:0:0): using BIOS timings, DMA mode 2
wdc2 at macobio0 offset 0x21000 irq 21: DMA
audio0 at daca0
ohci0 at pci1 dev 24 function 0 "Apple USB" rev 0x00: irq 27, version 1.0
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Apple OHCI root hub, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
"Apple USB" rev 0x00 at pci1 dev 25 function 0 not configured
mpcpcibr2 at mainbus0 pci: uni-north, Revision 0x16
pci2 at mpcpcibr2 bus 0
pchb2 at pci2 dev 11 function 0 "Apple Uni-N Eth" rev 0x00
gem0 at pci2 dev 15 function 0 "Apple Uni-N GMAC" rev 0x00: irq 41,
address 00:0a:27:8d:9a:e8
bmtphy0 at gem0 phy 0: BCM5201 10/100 PHY, rev. 2
axe0 at uhub0 port 1 configuration 1 interface 0
axe0: Cisco-Linksys USB200M v2, rev 2.00/0.01, addr 2, AX88772, address
00:10:60:06:5e:4d
ukphy0 at axe0 phy 16: Generic IEEE 802.3u media interface, rev. 1: OUI
0x000ec6, model 0x0001
bootpath: '/[EMAIL PROTECTED]/[EMAIL PROTECTED]/[EMAIL PROTECTED]/[EMAIL
PROTECTED]/bsd'
boot device: wd0.
root on wd0a
rootdev=0x0 rrootdev=0xb00 rawdev=0xb02
axe0: usb errors on rx: IOERROR
axe0: usb errors on rx: IOERROR
axe0: at uhub0 port 1 (addr 2) disconnected
ukphy0 detached
axe0 detached
axe0 at uhub0 port 1 configuration 1 interface 0
axe0: Cisco-Linksys USB200M v2, rev 2.00/0.01, addr 2, AX88772, address
00:10:60:06:5e:4d
ukphy0 at axe0 phy 16: Generic IEEE 802.3u media interface, rev. 1: OUI
0x000ec6, model 0x0001
