I just got my soekris net4511 in the mail today. I've got it setup to my
liking minus wep support. Below is my /etc/hostname.ral0 and my dmesg.
When I use nwkey 0x00000... my clients can no longer connect to the
wireless network. I was wondering if this is the method you use to set a
wep
key in hostap mode or if there is another way to do so.
Also I set "/dev/wd0a / ffs ro,noatime 1 1" is my /etc/fstab, but it
doesn't seem to mount read-only. I can still write to the system and my
chan
ges stay after a reboot. I get a Device-busy when it attempts to mount
during bootup.
Thanks.
/etc/hostname.ral0:
inet 192.168.1.1 255.255.255.0 NONE media autoselect mediaopt hostap mode
11g nwid soek
ris nwkey 0x4782cacc2983fefa894ff45863 chan 9
dmesg:
OpenBSD 4.0 (GENERIC) #1107: Sat Sep 16 19:15:58 MDT 2006
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: AMD Am486DX4 W/B or Am5x86 W/B 150 ("AuthenticAMD" 486-class)
cpu0: FPU
real mem = 66678784 (65116K)
avail mem = 52568064 (51336K)
using 839 buffers containing 3436544 bytes (3356K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 20/50/27, BIOS32 rev. 0 @ 0xf7840
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc8000/0x9000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
elansc0 at pci0 dev 0 function 0 "AMD ElanSC520 PCI" rev 0x00: product 0
stepping 1.1, CPU clock 100MHz, reset 40<SCP>
gpio0 at elansc0: 32 pins
cbb0 at pci0 dev 9 function 0 "TI PCI1410 CardBus" rev 0x02: irq 10
ral0 at pci0 dev 16 function 0 "Ralink RT2561" rev 0x00: irq 11, address
00:13:d3:85:7e:b4
ral0: MAC/BBP RT2561C, RF RT2527
sis0 at pci0 dev 18 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq
5, address 00:00:24:c6:c3:a8
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
sis1 at pci0 dev 19 function 0 "NS DP83815 10/100" rev 0x00, DP83816A: irq
9, address 00:00:24:c6:c3:a9
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 1 device 0 cacheline 0x10, lattimer 0x3f
pcmcia0 at cardslot0
isa0 at mainbus0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
wdc0 at isa0 port 0x1f0/8 irq 14
wd0 at wdc0 channel 0 drive 0: <SanDisk SDCFB-1024>
wd0: 4-sector PIO, LBA, 977MB, 2001888 sectors
wd0(wdc0:0:0): using BIOS timings
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
biomask f5c5 netmask ffe5 ttymask ffe7
pctr: no performance counters in CPU
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
