On 28 Dec 2007 at 21:29, Pawel Veselov wrote:
> Hi,
>
> Just had some experience installing 4.2 on ASUS m2a-vm... Wasn't pleasant.
Try -current, it will work better, with some gotchas thou.
> 3Gbs drive shows max of 0.2MBs tranfer rate (according to iostat). My
> old drive shows appx 30MB on IDE bus. Tested using dd if=/dev/zero
> of=file. Any disk access takes forever.
The drive is in pio-mode
> Selecting SATA interface as AHCI doesn't work (doesn't show up, or
> reboots the system when discovery attepmted).
In -current you can install to ahci/sata, but then generic doesn't boot.
You need to boot -c and disable ahci, change fstab to wd and then compile
a kernel with a KASSERT removed (in dev/pci/ahci.c, line 1757)
Change fstab again, and reboot. You'll get some ahci warnings, but it will work
> Installing 64bit version reboots the installer at the time disks were
> accessed.
>
> There seem to be some problems with built-in card, as in it won't send
> any packets, at least with 10MB media (re driver).
Still doesn't work in -current
Other quirks, the radeonhd driver doesn't work if you (only) use a dvi cable.
With an vga and a dvi cable you can run X
OpenBSD 4.2-current (MICRO.MP) #8: Sat Dec 29 13:01:47 CET 2007
[EMAIL PROTECTED]:/sys/arch/amd64/compile/MICRO.MP
real mem = 2011688960 (1918MB)
avail mem = 1941458944 (1851MB)
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.4 @ 0xf0000 (58 entries)
bios0: vendor Phoenix Technologies, LTD version "ASUS M2A-VM ACPI BIOS Revision
1603" date 11/30/2007
bios0: ASUSTeK Computer INC. M2A-VM
acpi0 at bios0: rev 2
acpi0: tables DSDT FACP SSDT HPET MCFG APIC
acpi0: wakeup devices USB0(S5) USB1(S5) USB2(S5) USB3(S5) USB4(S5) USB5(S5)
AZAL(S3) P2P_(S5) PCE2(S4) PCE3(S4) PCE4(S4) PCE5(S4) PCE6(S4) PCE7(S4)
PCE8(S4) UAR1(S5) UAR2(S5) PS2M(S5) PS2K(S5) PCI0(S5)
acpitimer0 at acpi0: 3579545 Hz, 32 bits
acpihpet0 at acpi0: 14318180 Hz
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: AMD Athlon(tm) X2 Dual Core Processor BE-2350, 2100.22 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW
cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB 64b/line
16-way L2 cache
cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu0: apic clock running at 199MHz
cpu1 at mainbus0: apid 1 (application processor)
cpu1: AMD Athlon(tm) X2 Dual Core Processor BE-2350, 2099.92 MHz
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW
cpu1: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 512KB 64b/line
16-way L2 cache
cpu1: ITLB 32 4KB entries fully associative, 8 4MB entries fully associative
cpu1: DTLB 32 4KB entries fully associative, 8 4MB entries fully associative
ioapic0 at mainbus0 apid 4 pa 0xfec00000, version 21, 24 pins
ioapic0: misconfigured as apic 0, remapped to apid 4
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 3 (P2P_)
acpiprt2 at acpi0: bus -1 (PCE2)
acpiprt3 at acpi0: bus -1 (PCE3)
acpiprt4 at acpi0: bus -1 (PCE4)
acpiprt5 at acpi0: bus -1 (PCE5)
acpiprt6 at acpi0: bus -1 (PCE6)
acpiprt7 at acpi0: bus 2 (PCE7)
acpiprt8 at acpi0: bus -1 (PCE8)
acpiprt9 at acpi0: bus 1 (AGP_)
acpicpu0 at acpi0: PSS
acpicpu1 at acpi0: PSS
acpitz0 at acpi0: critical temperature 75 degC
acpibtn0 at acpi0: PWRB
cpu0: PowerNow! K8 2099 MHz: speeds: 2100 2000 1800 1000 MHz
pci0 at mainbus0 bus 0: configuration mode 1
pchb0 at pci0 dev 0 function 0 "ATI RS690 Host" rev 0x00
ppb0 at pci0 dev 1 function 0 "ATI RS690 PCIE" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 5 function 0 "ATI Radeon X1250" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ppb1 at pci0 dev 7 function 0 "ATI RS690 PCIE" rev 0x00
pci2 at ppb1 bus 2
re0 at pci2 dev 0 function 0 "Realtek 8168" rev 0x01: RTL8168 2 (0x3800), apic
4 int 19 (irq 5), address 00:1b:fc:8b:7c:9c
rgephy0 at re0 phy 7: RTL8169S/8110S PHY, rev. 2
ahci0 at pci0 dev 18 function 0 "ATI IXP600 SATA" rev 0x00: apic 4 int 22 (irq
11), AHCI 1.1
scsibus0 at ahci0: 32 targets
sd0 at scsibus0 targ 0 lun 0: <ATA, Hitachi HDT72503, V54O> SCSI3 0/direct fixed
sd0: 305245MB, 38913 cyl, 255 head, 63 sec, 512 bytes/sec, 625142448 sec total
ahci0: stopping the port, softreset slot 5 was still active.
atascsi_atapi_cmd_done, timeout
ahci0: stopping the port, softreset slot 7 was still active.
atascsi_atapi_cmd_done, timeout
ahci0: stopping the port, softreset slot 9 was still active.
atascsi_atapi_cmd_done, timeout
ahci0: stopping the port, softreset slot 11 was still active.
atascsi_atapi_cmd_done, timeout
ahci0: stopping the port, softreset slot 13 was still active.
atascsi_atapi_cmd_done, timeout
ahci0: stopping the port, softreset slot 15 was still active.
atascsi_atapi_cmd_done, timeout
cd0 at scsibus0 targ 2 lun 0: <ASUS, DVD-E616A3T, 1.10> SCSI0 5/cdrom removable
ohci0 at pci0 dev 19 function 0 "ATI IXP600 USB" rev 0x00: apic 4 int 16 (irq
11), version 1.0, legacy support
ohci1 at pci0 dev 19 function 1 "ATI IXP600 USB" rev 0x00: apic 4 int 17 (irq
5), version 1.0, legacy support
ohci2 at pci0 dev 19 function 2 "ATI IXP600 USB" rev 0x00: apic 4 int 18 (irq
3), version 1.0, legacy support
ohci3 at pci0 dev 19 function 3 "ATI IXP600 USB" rev 0x00: apic 4 int 17 (irq
5), version 1.0, legacy support
ohci4 at pci0 dev 19 function 4 "ATI IXP600 USB" rev 0x00: apic 4 int 18 (irq
3), version 1.0, legacy support
ehci0 at pci0 dev 19 function 5 "ATI IXP600 USB2" rev 0x00: apic 4 int 19 (irq
5)
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "ATI EHCI root hub" rev 2.00/1.00 addr 1
piixpm0 at pci0 dev 20 function 0 "ATI IXPX00 SMBus" rev 0x14: SMI
iic0 at piixpm0
spdmem0 at iic0 addr 0x50: 1GB DDR2 SDRAM non-parity PC2-6400CL5
spdmem1 at iic0 addr 0x51: 1GB DDR2 SDRAM non-parity PC2-6400CL5
pciide0 at pci0 dev 20 function 1 "ATI IXP600 IDE" rev 0x00: DMA, channel 0
configured to compatibility, channel 1 configured to compatibility
azalia0 at pci0 dev 20 function 2 "ATI IXP600 HD Audio" rev 0x00: apic 4 int 16
(irq 11)
azalia0: codec[s]: Realtek ALC883
audio0 at azalia0
pcib0 at pci0 dev 20 function 3 "ATI IXP600 LPC" rev 0x00
ppb2 at pci0 dev 20 function 4 "ATI IXP600 PCI" rev 0x00
pci3 at ppb2 bus 3
em0 at pci3 dev 5 function 0 "Intel PRO/1000MT (82541GI)" rev 0x00: apic 4 int
20 (irq 10), address 00:0e:0c:5f:c4:8f
puc0 at pci3 dev 6 function 0 "Lava Quad Serial" rev 0x00: ports: 4 com
com2 at puc0 port 0 apic 4 int 21 (irq 10): ns16550a, 16 byte fifo
com3 at puc0 port 1 apic 4 int 21 (irq 10): ns16550a, 16 byte fifo
com4 at puc0 port 2 apic 4 int 21 (irq 10): ns16550a, 16 byte fifo
com5 at puc0 port 3 apic 4 int 21 (irq 10): ns16550a, 16 byte fifo
puc1 at pci3 dev 6 function 1 "Lava Quad Serial" rev 0x00: ports: 4 com
com6 at puc1 port 0 apic 4 int 21 (irq 10): ns16550a, 16 byte fifo
com7 at puc1 port 1 apic 4 int 21 (irq 10): ns16550a, 16 byte fifo
com8 at puc1 port 2 apic 4 int 21 (irq 10): ns16550a, 16 byte fifo
com9 at puc1 port 3 apic 4 int 21 (irq 10): ns16550a, 16 byte fifo
pchb1 at pci0 dev 24 function 0 "AMD AMD64 HyperTransport" rev 0x00
pchb2 at pci0 dev 24 function 1 "AMD AMD64 Address Map" rev 0x00
pchb3 at pci0 dev 24 function 2 "AMD AMD64 DRAM Cfg" rev 0x00
pchb4 at pci0 dev 24 function 3 "AMD AMD64 Misc Cfg" rev 0x00
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb2 at ohci1: USB revision 1.0
uhub2 at usb2 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb3 at ohci2: USB revision 1.0
uhub3 at usb3 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb4 at ohci3: USB revision 1.0
uhub4 at usb4 "ATI OHCI root hub" rev 1.00/1.00 addr 1
usb5 at ohci4: USB revision 1.0
uhub5 at usb5 "ATI OHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
it0 at isa0 port 0x228/8: IT8716F rev 0x01
uhidev0 at uhub2 port 1 configuration 1 interface 0 "Logitech Trackball" rev
1.10/2.20 addr 2
uhidev0: iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir.
wsmouse0 at ums0 mux 0
softraid0 at root
root on sd0a swap on sd0b dump on sd0b
