Hi,
after upgrading from
OpenBSD 4.2-current (GENERIC) #599: Fri Dec 14 17:13:48 MST 2007
to
OpenBSD 4.3-current (GENERIC) #820: Wed Apr 16 21:01:55 MDT 2008
a few days ago the following SSH error with the Soekris 4801 + vpn14x1
is back:
Received disconnect from xxx.xxx.xxx.xxx: 2: Corrupted MAC on input
I hoped that it had been fixed for good by now... :-(
Michael
*dmesg of the old version which worked:*
OpenBSD 4.2-current (GENERIC) #599: Fri Dec 14 17:13:48 MST 2007
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by National Semi ("Geode by NSC"
586-class) 267 MHz
cpu0: FPU,TSC,MSR,CX8,CMOV,MMX
cpu0: TSC disabled
real mem = 268005376 (255MB)
avail mem = 251260928 (239MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 20/50/29, BIOS32 rev. 0 @ 0xf7840
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc8000/0x9000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00
sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 10, address 00:00:24:c7:7f:64
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 10, address 00:00:24:c7:7f:65
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 10, address 00:00:24:c7:7f:66
nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1
ppb0 at pci0 dev 10 function 0 "TI PCI2250 PCI-PCI" rev 0x02
pci1 at ppb0 bus 1
sis3 at pci1 dev 0 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 9, address 00:00:24:c7:4c:2c
nsphyter3 at sis3 phy 0: DP83815 10/100 PHY, rev. 1
sis4 at pci1 dev 1 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 5, address 00:00:24:c7:4c:2d
nsphyter4 at sis4 phy 0: DP83815 10/100 PHY, rev. 1
sis5 at pci1 dev 2 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 9, address 00:00:24:c7:4c:2e
nsphyter5 at sis5 phy 0: DP83815 10/100 PHY, rev. 1
sis6 at pci1 dev 3 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 5, address 00:00:24:c7:4c:2f
nsphyter6 at sis6 phy 0: DP83815 10/100 PHY, rev. 1
hifn0 at pci0 dev 14 function 0 "Hifn 7955/7954" rev 0x00: LZS 3DES ARC4
MD5 SHA1 RNG AES PK, 32KB dram, irq 11
gscpcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00
gpio0 at gscpcib0: 64 pins
"NS SC1100 SMI" rev 0x00 at pci0 dev 18 function 1 not configured
pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA, channel
0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <CF300>
wd0: 1-sector PIO, LBA, 983MB, 2014992 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev 0x00: iid 6
revision 3 wdstatus 9<WDRST,WDOVF>
ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq 5,
version 1.0, legacy support
isa0 at gscpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
gpio1 at nsclpcsio0: 29 pins
gscsio0 at isa0 port 0x15c/2: SC1100 SIO rev 1:
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "Compaq OHCI root hub" rev 1.00/1.00 addr 1
biomask f1e5 netmask ffe5 ttymask ffe7
ugen0 at uhub0 port 1 "American Power Conversion Back-UPS CS 500
FW:808.q5.I USB FW:q5" rev 1.10/0.06 addr 2
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
*dmesg of the new version with the error again:*
OpenBSD 4.3-current (GENERIC) #820: Wed Apr 16 21:01:55 MDT 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by National Semi ("Geode by NSC"
586-class) 267 MHz
cpu0: FPU,TSC,MSR,CX8,CMOV,MMX
cpu0: TSC disabled
real mem = 268005376 (255MB)
avail mem = 251047936 (239MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 20/50/29, BIOS32 rev. 0 @ 0xf7840
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc8000/0x9000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00
sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 10, address 00:00:24:c7:7f:64
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 10, address 00:00:24:c7:7f:65
nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1
sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 10, address 00:00:24:c7:7f:66
nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1
ppb0 at pci0 dev 10 function 0 "TI PCI2250 PCI-PCI" rev 0x02
pci1 at ppb0 bus 1
sis3 at pci1 dev 0 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 9, address 00:00:24:c7:4c:2c
nsphyter3 at sis3 phy 0: DP83815 10/100 PHY, rev. 1
sis4 at pci1 dev 1 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 5, address 00:00:24:c7:4c:2d
nsphyter4 at sis4 phy 0: DP83815 10/100 PHY, rev. 1
sis5 at pci1 dev 2 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 9, address 00:00:24:c7:4c:2e
nsphyter5 at sis5 phy 0: DP83815 10/100 PHY, rev. 1
sis6 at pci1 dev 3 function 0 "NS DP83815 10/100" rev 0x00, DP83816A:
irq 5, address 00:00:24:c7:4c:2f
nsphyter6 at sis6 phy 0: DP83815 10/100 PHY, rev. 1
hifn0 at pci0 dev 14 function 0 "Hifn 7955/7954" rev 0x00: LZS 3DES ARC4
MD5 SHA1 RNG AES PK, 32KB dram, irq 11
gscpcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00
gpio0 at gscpcib0: 64 pins
"NS SC1100 SMI" rev 0x00 at pci0 dev 18 function 1 not configured
pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: DMA, channel
0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <CF300>
wd0: 1-sector PIO, LBA, 983MB, 2014992 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev 0x00: iid 6
revision 3 wdstatus 0
ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev 0x08: irq 5,
version 1.0, legacy support
isa0 at gscpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS
gpio1 at nsclpcsio0: 29 pins
gscsio0 at isa0 port 0x15c/2: SC1100 SIO rev 1:
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "Compaq OHCI root hub" rev 1.00/1.00 addr 1
biomask f1e5 netmask ffe5 ttymask ffe7
ugen0 at uhub0 port 1 "American Power Conversion Back-UPS CS 500
FW:808.q5.I USB FW:q5" rev 1.10/0.06 addr 2
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
