Same here on a Thinkpad x31. Mitja
> -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] > On Behalf Of Emilio Perea > Sent: Sunday, August 03, 2008 6:29 AM > To: misc@openbsd.org > Subject: Problem with current i386 snapshot > > This build seems to go into an endless reboot cycle, rebooting before > anything shows up in the console of a Soekris net4801. The previous > snapshot (build #1004) works fine. Unfortunately I have > nothing to show > for it as far as filing a proper bug report. BIOS screen followed by > the changing console to com0 message followed by the BIOS screen etc. > > Problem build: > OpenBSD 4.4-beta (GENERIC) #1010: Sat Aug 2 12:39:46 MDT 2008 > [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC > > Last working version dmesg: > OpenBSD 4.4-beta (GENERIC) #1004: Thu Jul 31 00:42:16 MDT 2008 > [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC > cpu0: Geode(TM) Integrated Processor by National Semi ("Geode > by NSC" 586-class) 267 MHz > cpu0: FPU,TSC,MSR,CX8,CMOV,MMX > cpu0: TSC disabled > real mem = 133787648 (127MB) > avail mem = 120946688 (115MB) > mainbus0 at root > bios0 at mainbus0: AT/286+ BIOS, date 20/80/03, BIOS32 rev. 0 > @ 0xf7840 > pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000 > pcibios0: pcibios_get_intr_routing - function not supported > pcibios0: PCI IRQ Routing information unavailable. > pcibios0: PCI bus #0 is the last bus > bios0: ROM list: 0xc8000/0x9000 > cpu0 at mainbus0 > pci0 at mainbus0 bus 0: configuration mode 1 (bios) > pchb0 at pci0 dev 0 function 0 "Cyrix GXm PCI" rev 0x00 > sis0 at pci0 dev 6 function 0 "NS DP83815 10/100" rev 0x00, > DP83816A: irq 10, address 00:00:24:c2:9e:30 > nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1 > sis1 at pci0 dev 7 function 0 "NS DP83815 10/100" rev 0x00, > DP83816A: irq 10, address 00:00:24:c2:9e:31 > nsphyter1 at sis1 phy 0: DP83815 10/100 PHY, rev. 1 > sis2 at pci0 dev 8 function 0 "NS DP83815 10/100" rev 0x00, > DP83816A: irq 10, address 00:00:24:c2:9e:32 > nsphyter2 at sis2 phy 0: DP83815 10/100 PHY, rev. 1 > gscpcib0 at pci0 dev 18 function 0 "NS SC1100 ISA" rev 0x00 > gpio0 at gscpcib0: 64 pins > "NS SC1100 SMI" rev 0x00 at pci0 dev 18 function 1 not configured > pciide0 at pci0 dev 18 function 2 "NS SCx200 IDE" rev 0x01: > DMA, channel 0 wired to compatibility, channel 1 wired to > compatibility > wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFX-2048> > wd0: 4-sector PIO, LBA, 1953MB, 4001760 sectors > wd0(pciide0:0:0): using PIO mode 4 > geodesc0 at pci0 dev 18 function 5 "NS SC1100 X-Bus" rev > 0x00: iid 6 revision 3 wdstatus 0 > ohci0 at pci0 dev 19 function 0 "Compaq USB OpenHost" rev > 0x08: irq 11, version 1.0, legacy support > isa0 at gscpcib0 > isadma0 at isa0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > com0: console > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard > pcppi0 at isa0 port 0x61 > midi0 at pcppi0: <PC speaker> > spkr0 at pcppi0 > nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 9: GPIO VLM TMS > gpio1 at nsclpcsio0: 29 pins > gscsio0 at isa0 port 0x15c/2: SC1100 SIO rev 1: > npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 > usb0 at ohci0: USB revision 1.0 > uhub0 at usb0 "Compaq OHCI root hub" rev 1.00/1.00 addr 1 > biomask fbe5 netmask ffe5 ttymask ffff > softraid0 at root > root on wd0a swap on wd0b dump on wd0b
