Hi,
I installed snapshot(08/06) on my thinkpad 240x.When I tried to start X,
the lcd flickered and then went black. I was not able to switch consoles
and the only thing to do would be ssh to the machine and reboot or
powercycle it. This apparently has been a known problem for a few
years?and I read reports It was broken in X 4.2.0 release.
Is anyone working on this (Todd?). Can I help?How?I was thinking to
forward port 4.1.0 siliconmotion code, would that be a recommended
approach?
Regards
Mohamed
Below is the output of dmesg and X's log
Dmesg:
OpenBSD 4.4 (GENERIC) #1019: Wed Aug 6 13:24:57 MDT 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III ("GenuineIntel" 686-class) 498 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,
SSE
real mem = 200830976 (191MB)
avail mem = 185638912 (177MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 12/21/99, BIOS32 rev. 0 @ 0xfd8b0,
SMBIOS re
v. 2.3 @ 0xec390 (31 entries)
bios0: vendor IBM version "1.03.09" date 12/21/1999
bios0: IBM 260961U
apm0 at bios0: Power Management spec V1.2
apm0: battery life expectancy 100%
apm0: AC on, battery charge high
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 2.1 @ 0xfd8b0/0x750
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf60/128 (6 entries)
pcibios0: PCI Interrupt Router at 000:07:0 ("Intel 82371FB ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0xc000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82440MX Host" rev 0x01
pcib0 at pci0 dev 7 function 0 "Intel 82440MX ISA" rev 0x01
pciide0 at pci0 dev 7 function 1 "Intel 82440MX IDE" rev 0x00: DMA,
channel 0 wire
d to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <IC25N080ATMR04-0>
wd0: 16-sector PIO, LBA, 73252MB, 150020514 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 disabled (no drives)
uhci0 at pci0 dev 7 function 2 "Intel 82440MX USB" rev 0x00: irq 11
piixpcib0 at pci0 dev 7 function 3 "Intel 82440MX Power" rev 0x00
vga1 at pci0 dev 9 function 0 "Silicon Motion LynxEM+" rev 0xa0
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
drm at vga1 unsupported
cbb0 at pci0 dev 10 function 0 "TI PCI1211 CardBus" rev 0x00: irq
11clct0 at pci0 dev 11 function 0 "Cirrus Logic CS4281 CrystalClear" rev
0x01 irq 5
ac97: codec id 0x43525914 (Cirrus Logic CS4297A rev 4)
ac97: codec features headphone, 20 bit DAC, 18 bit ADC, Crystal Semi 3D
audio0 at clct0
"AT&T/Lucent LTMODEM" rev 0x01 at pci0 dev 12 function 0 not configured
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0lpt2 at isa0 port 0x3bc/4: polled
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
usb0 at uhci0: USB revision 1.0
uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa at piixpcib0 not configured
cbb0: bad Vcc request. sock_ctrl 0x0, sock_status 0x30000b20
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 1 device 0 cacheline 0x0, lattimer 0x20
pcmcia0 at cardslot0
biomask efc5 netmask efc5 ttymask ffdf
mtrr: Pentium Pro MTRR support
cbb0: bad Vcc request. sock_ctrl 0x30, sock_status 0x30000b20
rl0 at cardbus0 dev 0 function 0 "Realtek 8139" rev 0x10: irq 11,
address 00:14:d1
:51:87:c9
rlphy0 at rl0 phy 0: RTL internal PHY
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
Xorg.0.log snippet
(WW) Silicon Motionremove MTRR fd400000 - fd800000
(==) Silicon MotionWrite-combining range (0xfd400000,0x400000) was
already clear
(WW) Silicon Motionset MTRR fd000000 - fd200000
(==) Silicon MotionWrite-combining range (0xfd000000,0x200000)
(II) Silicon MotionCursor Offset: 001FFC00
(II) Silicon MotionReserved: 001FF800
(II) Silicon MotionvgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset
is 0x0000
(WW) Silicon Motionremove MTRR a0000 - b0000
(==) Silicon MotionWrite-combining range (0xa0000,0x10000) was already
clear
(WW) Silicon Motionremove MTRR a0000 - c0000
(==) Silicon MotionWrite-combining range (0xa0000,0x20000) was already
clear
(II) Silicon MotionPrimary V_BIOS segment is: 0xc000
(WW) Silicon Motionremove MTRR 0 - 1000
(==) Silicon MotionWrite-combining range (0x0,0x1000) was already clear
(II) Silicon MotionCurrent mode 0x00.
(II) Silicon Motion SMI_GEReset called from
/tmp_mnt/cvs/cvs.d/hack/todd/x/xenocara/driver/xf86-video-siliconmotio
n/src/smi_driver.c line 1566
(II) Silicon Motion SMI_GEReset called from
/tmp_mnt/cvs/cvs.d/hack/todd/x/xenocara/driver/xf86-video-siliconmotio
n/src/smi_accel.c line 267
(II) Silicon Motion SMI_GEReset called from
/tmp_mnt/cvs/cvs.d/hack/todd/x/xenocara/driver/xf86-video-siliconmotio
n/src/smi_accel.c line 267
(II) Silicon Motion SMI_GEReset called from
/tmp_mnt/cvs/cvs.d/hack/todd/x/xenocara/driver/xf86-video-siliconmotio
n/src/smi_accel.c line 267
(II) Silicon Motion SMI_GEReset called from
/tmp_mnt/cvs/cvs.d/hack/todd/x/xenocara/driver/xf86-video-siliconmotio
n/src/smi_accel.c line 267
(II) Silicon Motion SMI_GEReset called from
/tmp_mnt/cvs/cvs.d/hack/todd/x/xenocara/driver/xf86-video-siliconmotio
n/src/smi_accel.c line 267
(II) Silicon Motion SMI_GEReset called from
/tmp_mnt/cvs/cvs.d/hack/todd/x/xenocara/driver/xf86-video-siliconmotio
n/src/smi_accel.c line 267
(II) Silicon Motion SMI_GEReset called from
/tmp_mnt/cvs/cvs.d/hack/todd/x/xenocara/driver/xf86-video-siliconmotio
n/src/smi_accel.c line 267
This keeps going till I powercycle the machine.
Regards
Mohamed
