Hello,
I have Alix 2D3 (and another 2D13) with Tonze PC-620C miniPCI. It mostly
works ok, but I am still hunting some problem - one or two times for a
month it falls to ddb> prompt. I build OpenBSD completelly from cvs just
about every month - it seems it is time for new build of -current.
Best regards,
Alexander
# ifconfig ral0
ral0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu
1500
lladdr 00:17:b7:30:41:ab
priority: 4
groups: wlan
media: IEEE802.11 autoselect mode 11g hostap
status: active
ieee80211: nwid **** chan 7 bssid 00:17:b7:30:41:ab wpapsk
0x**** wpaprotos wpa1,wpa2 wpaakms psk wpaciphers ccmp wpagroupcipher
ccmp 100dBm
inet 192.168.254.1 netmask 0xffffff00 broadcast 192.168.254.255
inet **** netmask 0xfffffff8 broadcast ****
# dmesg
OpenBSD 4.7-current (FLASHRD) #19: Wed Apr 14 23:29:29 CEST 2010
r...@kraken.gremlin.cz:/usr/src/sys/arch/i386/compile/FLASHRD
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD"
586-class) 499 MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX
real mem = 268009472 (255MB)
avail mem = 247640064 (236MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 12/10/07, BIOS32 rev. 0 @ 0xfceb2
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xe0000/0xa800
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x33
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
vr0 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 10,
address 00:0d:b9:17:23:d4
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
vr1 at pci0 dev 10 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11,
address 00:0d:b9:17:23:d5
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
vr2 at pci0 dev 11 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12,
address 00:0d:b9:17:23:d6
ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
ral0 at pci0 dev 12 function 0 "Ralink RT2561S" rev 0x00: irq 9, address
00:17:b7:30:41:ab
ral0: MAC/BBP RT2561C, RF RT2527
glxpcib0 at pci0 dev 15 function 0 "AMD CS5536 ISA" rev 0x03: rev 3,
32-bit 3579545Hz timer, watchdog, gpio
gpio0 at glxpcib0: 32 pins
pciide0 at pci0 dev 15 function 2 "AMD CS5536 IDE" rev 0x01: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <CF CARD 4GB>
wd0: 1-sector PIO, LBA, 3599MB, 7372512 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 15 function 4 "AMD CS5536 USB" rev 0x02: irq 15,
version 1.0, legacy support
ehci0 at pci0 dev 15 function 5 "AMD CS5536 USB" rev 0x02: irq 15
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
isa0 at glxpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
biomask e1ef netmask ffef ttymask ffff
mtrr: K6-family MTRR support (2 registers)
nvram: invalid checksum
rd0: fixed, 6080 blocks
umass0 at uhub0 port 1 configuration 1 interface 0 "Kingston
DataTraveler 2.0" rev 2.00/1.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <Kingston, DataTraveler 2.0, 1.00> SCSI2
0/direct removable
sd0: 7643MB, 512 bytes/sec, 15654848 sec total
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
root on rd0a swap on rd0b dump on rd0b
clock: unknown CMOS layout
On Mon, 2010-05-24 at 22:10 +0200, Piotr Komborski wrote:
> Hello,
>
> I'm going to set OpenBSD based AP on ALIX board. I've red ral(4) and ath(4)
> manpages but mentioned mPCI card models are really hard to find on the
> market. I found only Ralink RT2800 based Sparklan WMIR-200N which is too
> expensive for me (60$).
> Can anybody recommend me 802.11g miniPCI card that is able to work in host
> AP mode?
>
> regards
>
> Piotr
