On Wed, Jul 28, 2010 at 2:43 AM, Fred Crowson <fred.crow...@gmail.com> wrote: > On 28 July 2010 06:57, Nathan Sandver <nsand...@gmail.com> wrote: >> >> The swap partition I created at wd1b is correctly listed in /etc/fstab: >> # cat /mnt/etc/fstab >> /dev/wd1b none swap sw 0 0 >> /dev/wd0a / ffs rw 1 1 >> /dev/wd1a /usr ffs rw,nodev 1 2 >> > > What happens when you remove the wd1b line from fstab?
Exactly the same thing. The system hangs at the same point, with the same message (dmesg output below). Rebooting with command: boot Boot device: disk File and args: OpenBSD IEEE 1275 Bootblock 1.3 ..>> OpenBSD BOOT 1.3 Trying bsd... Booting /p...@1f,0/p...@1,1/i...@3/d...@0,0:a/bsd 6372...@0x1000000+616@0x1613d98+190...@0x1800000+4004176@0x182e6b0 symbols @ 0xfef642c0 81+390912+244649 start=0x1000000 [ using 636360 bytes of bsd ELF symbol table ] console is /p...@1f,0/p...@1,1/e...@1/s...@14,400000:b Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2010 OpenBSD. All rights reserved. http://www.OpenBSD.org OpenBSD 4.7 (GENERIC) #258: Wed Mar 17 23:40:34 MDT 2010 dera...@sparc64.openbsd.org:/usr/src/sys/arch/sparc64/compile/GENERIC real mem = 134217728 (128MB) avail mem = 115802112 (110MB) mainbus0 at root: Sun Ultra 5/10 UPA/PCI (UltraSPARC-IIi 360MHz) cpu0 at mainbus0: SUNW,UltraSPARC-IIi (rev 9.1) @ 360 MHz cpu0: physical 16K instruction (32 b/l), 16K data (32 b/l), 256K external (64 b/l) psycho0 at mainbus0 addr 0xfffc4000: SUNW,sabre, impl 0, version 0, ign 7c0 psycho0: bus range 0-2, PCI bus 0 psycho0: dvma map c0000000-dfffffff pci0 at psycho0 ppb0 at pci0 dev 1 function 1 "Sun Simba PCI-PCI" rev 0x13 pci1 at ppb0 bus 1 ebus0 at pci1 dev 1 function 0 "Sun PCIO EBus2" rev 0x01 auxio0 at ebus0 addr 726000-726003, 728000-728003, 72a000-72a003, 72c000-72c003, 72f000-72f003 power0 at ebus0 addr 724000-724003 ivec 0x25 "SUNW,pll" at ebus0 addr 504000-504002 not configured sab0 at ebus0 addr 400000-40007f ivec 0x2b: rev 3.2 sabtty0 at sab0 port 0 sabtty1 at sab0 port 1: console comkbd0 at ebus0 addr 3083f8-3083ff ivec 0x29: no keyboard comms0 at ebus0 addr 3062f8-3062ff ivec 0x2a wsmouse0 at comms0 mux 0 lpt0 at ebus0 addr 3043bc-3043cb, 30015c-30015d, 700000-70000f ivec 0x22: polled clock1 at ebus0 addr 0-1fff: mk48t59 "flashprom" at ebus0 addr 0-fffff not configured audioce0 at ebus0 addr 200000-2000ff, 702000-70200f, 704000-70400f, 722000-722003 ivec 0x23 ivec 0x24: nvaddrs 0 audio0 at audioce0 hme0 at pci1 dev 1 function 1 "Sun HME" rev 0x01: ivec 0x7e1, address 08:00:20:d1:7e:f8 nsphy0 at hme0 phy 1: DP83840 10/100 PHY, rev. 1 machfb0 at pci1 dev 2 function 0 "ATI Mach64" rev 0x5c machfb0: ATY,GT-C, 1152x900 wsdisplay0 at machfb0 mux 1 wsdisplay0: screen 0 added (std, sun emulation) pciide0 at pci1 dev 3 function 0 "CMD Technology PCI0646" rev 0x03: DMA, channel 0 configured to native-PCI, channel 1 configured to native-PCI pciide0: using ivec 0x7e0 for native-PCI interrupt wd0 at pciide0 channel 0 drive 0: <LEXAR ATA FLASH> wd0: 4-sector PIO, LBA, 489MB, 1001952 sectors wd1 at pciide0 channel 0 drive 1: <ST34313A> wd1: 32-sector PIO, LBA, 4112MB, 8421840 sectors wd0(pciide0:0:0): using PIO mode 4 wd1(pciide0:0:1): using PIO mode 4, DMA mode 2 atapiscsi0 at pciide0 channel 1 drive 0 scsibus0 at atapiscsi0: 2 targets cd0 at scsibus0 targ 0 lun 0: <LG, CD-ROM CRD-8322B, 1.05> ATAPI 5/cdrom removable cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 ppb1 at pci0 dev 1 function 0 "Sun Simba PCI-PCI" rev 0x13 pci2 at ppb1 bus 2 vscsi0 at root scsibus1 at vscsi0: 256 targets softraid0 at root bootpath: /p...@1f,0/p...@1,1/i...@3,0/d...@0,0 root on wd0a swap on wd0b dump on wd0b -- Nathan Sandver <nsand...@gmail.com>