Hi list,
i updated my OpenBSD box this weekend and it seems, my usb-devices
aren't working anymore; they did before. I updated my 4.6-stable to 4.7
and then to 4.7-stable. I tried a printer, a mouse and a harddisk, none
gets recognized by the system; the harddisk powers on though. is there
any chance, an upgrade to 4.8-beta will fix things for me?
fwiw, i have outputs from my fedora on my notebook when i connect the
devices (don't have a different OpenBSD installation at the moment,
dmesg at the end of this mail).
printer:
usb 1-5: new high speed USB device using ehci_hcd and address 3
usb 1-5: New USB device found, idVendor=04b4, idProduct=6560
usb 1-5: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-5:1.0: USB hub found
hub 1-5:1.0: 4 ports detected
usb 1-5.1: new full speed USB device using ehci_hcd and address 4
usb 1-5.1: New USB device found, idVendor=0482, idProduct=0011
usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-5.1: Product: Kyocera Mita FS-920
usb 1-5.1: Manufacturer: Kyocera Mita
usb 1-5.1: SerialNumber: XLG5523438
usblp0: USB Bidirectional printer dev 4 if 0 alt 0 proto 2 vid 0x0482
pid 0x0011
usbcore: registered new interface driver usblp
mouse:
usb 5-1: USB disconnect, address 2
usb 5-1: new low speed USB device using uhci_hcd and address 3
usb 5-1: New USB device found, idVendor=046d, idProduct=c043
usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 5-1: Product: USB-PS/2 Optical Mouse
usb 5-1: Manufacturer: Logitech
input: Logitech USB-PS/2 Optical Mouse as
/devices/pci0000:00/0000:00:1d.3/usb5/5-1/5-1:1.0/input/input9
generic-usb 0003:046D:C043.0002: input,hidraw0: USB HID v1.10 Mouse
[Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.3-1/input0
harddisk:
usb 1-5: new high speed USB device using ehci_hcd and address 5
usb 1-5: New USB device found, idVendor=04fc, idProduct=0c15
usb 1-5: New USB device strings: Mfr=2, Product=3, SerialNumber=1
usb 1-5: Product: USB to Serial-ATA bridge
usb 1-5: Manufacturer: Sunplus Technology Inc.
usb 1-5: SerialNumber: FUJITSU MH NW9ST7126D12
Initializing USB Mass Storage driver...
scsi2 : usb-storage 1-5:1.0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
scsi 2:0:0:0: Direct-Access FUJITSU MHV2120BH PL PQ: 0 ANSI: 2
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 2:0:0:0: [sdb] 234441648 512-byte logical blocks: (120 GB/111 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 38 00 00 00
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] Attached SCSI disk
here's the dmesg (i tried all three devices, but none shows up):
~ $ dmesg
OpenBSD 4.7-stable (GENERIC) #1: Sun Aug 8 10:18:26 CEST 2010
r...@xxx:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III ("GenuineIntel" 686-class) 1 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
real mem = 266891264 (254MB)
avail mem = 249896960 (238MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 07/15/02, BIOS32 rev. 0 @ 0xfd880,
SMBIOS rev. 2.31 @ 0xefce0 (77 entries)
bios0: vendor FUJITSU SIEMENS // Phoenix Technologies Ltd. version "4.06
Rev. 1.12.1215" date 07/15/2002
bios0: FUJITSU SIEMENS SCENIC xS/SCOVERY xS
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 2.1 @ 0xfd880/0x780
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf20/192 (10 entries)
pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0xc000! 0xcc000/0x4000! 0xd0000/0x1800
0xd1800/0x1000 0xd2800/0x4800 0xdf000/0x1000!
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82815 Host" rev 0x04
vga1 at pci0 dev 2 function 0 "Intel 82815 Video" rev 0x04
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
intagp0 at vga1
agp0 at intagp0: aperture at 0xf8000000, size 0x4000000
ppb0 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x05
pci1 at ppb0 bus 1
fxp0 at pci1 dev 8 function 0 "Intel 82562" rev 0x03, i82562: irq 9,
address 00:30:05:2f:80:de
inphy0 at fxp0 phy 1: i82562EM 10/100 PHY, rev. 0
em0 at pci1 dev 9 function 0 "Intel PRO/1000GT (82541GI)" rev 0x05: irq
11, address 00:1b:21:3a:2a:53
pciide0 at pci1 dev 11 function 0 "CMD Technology SiI3512 SATA" rev
0x01: DMA
pciide0: using irq 9 for native-PCI interrupt
pciide0: port 0: device present, speed: 1.5Gb/s
wd0 at pciide0 channel 0 drive 0: <WDC WD1000FYPS-01ZKB1>
wd0: 16-sector PIO, LBA48, 953869MB, 1953525168 sectors
wd0(pciide0:0:0): using BIOS timings, Ultra-DMA mode 6
ichpcib0 at pci0 dev 31 function 0 "Intel 82801BA LPC" rev 0x05: 24-bit
timer at 3579545Hz
pciide1 at pci0 dev 31 function 1 "Intel 82801BA IDE" rev 0x05: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd1 at pciide1 channel 0 drive 0: <FC256>
wd1: 1-sector PIO, LBA, 249MB, 511056 sectors
wd1(pciide1:0:0): using PIO mode 4
pciide1: channel 1 disabled (no drives)
uhci0 at pci0 dev 31 function 2 "Intel 82801BA USB" rev 0x05: irq 9
ichiic0 at pci0 dev 31 function 3 "Intel 82801BA SMBus" rev 0x05: irq 5
iic0 at ichiic0
spdmem0 at iic0 addr 0x55: 128MB SDRAM non-parity PC133CL2
spdmem1 at iic0 addr 0x56: 128MB SDRAM non-parity PC133CL2
uhci1 at pci0 dev 31 function 4 "Intel 82801BA USB" rev 0x05: irq 11
auich0 at pci0 dev 31 function 5 "Intel 82801BA AC97" rev 0x05: irq 5,
ICH2 AC97
ac97: codec id 0x41445360 (Analog Devices AD1885)
ac97: codec features headphone, Analog Devices Phat Stereo
audio0 at auich0
isa0 at ichpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
usb0 at uhci0: USB revision 1.0
uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb1 at uhci1: USB revision 1.0
uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
biomask ff67 netmask ff67 ttymask ffff
mtrr: Pentium Pro MTRR support
uhub2 at uhub0 port 2 "Cypress Semiconductor USB2 Hub" rev 2.00/0.0b addr 2
vscsi0 at root
scsibus0 at vscsi0: 256 targets
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
