Revision: 405be73e7092
Author: [email protected] <[email protected]>
Date: Thu Jun 7 02:54:21 2012
Log: Added SS7 Intro wiki
http://code.google.com/p/jss7/source/detail?r=405be73e7092&repo=wiki
Added:
/SS7Introduction.wiki
Modified:
/SideBar.wiki
=======================================
--- /dev/null
+++ /SS7Introduction.wiki Thu Jun 7 02:54:21 2012
@@ -0,0 +1,34 @@
+This wiki is meant to give a very small introduction on SS7. There are
many books available which can provide complete details of SS7. Below are
few of my recommendations
+ *
[http://www.amazon.com/Signaling-System-No-SS7-Architecture/dp/1587050404
Signaling System No. 7 (SS7/C7): Protocol, Architecture, and Services
(Networking Technology)]
+ *
[http://www.amazon.com/Signaling-System-McGraw-Hill-Computer-Communications/dp/007146879X/ref=sr_1_1?s=books&ie=UTF8&qid=1339062422&sr=1-1
Signaling System #7, Fifth Edition (McGraw-Hill Computer Communications
Series)]
+
+=== SS7 Introduction ===
+Common Channel Signaling System No. 7 (i.e., SS7 or C7) is a global
standard for telecommunications defined by the
[http://www.voip-info.org/wiki/view/ITU International Telecommunication
Union] (ITU) Telecommunication Standardization Sector (ITU-T). The standard
defines the procedures and protocol by which network elements in the public
switched telephone network (PSTN) exchange information over a digital
signaling network to effect wireless (cellular) and wireline call setup,
routing and control. The ITU definition of SS7 allows for national variants
such as the American National Standards Institute (ANSI) and Bell
Communications Research (Telcordia Technologies) standards used in North
America and the [http://www.voip-info.org/wiki/view/ETSI European
Telecommunications Standards Institute] ( ETSI ) standard used in Europe.
+
+
+==== SS7 Protocol Stack overview ====
+The hardware and software functions of the SS7 protocol are divided into
functional abstractions called "levels". These levels map loosely to the
Open Systems Interconnect (OSI) 7-layer model defined by the International
Standards Organization (ISO).
+
+
+===== Message Transfer Part =====
+The Message Transfer Part (MTP) is divided into three levels. The lowest
level, *MTP Level 1*, is equivalent to the OSI Physical Layer. MTP Level 1
defines the physical, electrical, and functional characteristics of the
digital signaling link. Physical interfaces defined include E-1 (2048 kb/s;
32 64 kb/s channels), DS-1 (1544 kb/s; 24 64kb/s channels), V.35 (64 kb/s),
DS-0 (64 kb/s), and DS-0A (56 kb/s).
+
+*MTP Level 2* ensures accurate end-to-end transmission of a message across
a signaling link. Level 2 implements flow control, message sequence
validation, and error checking. When an error occurs on a signaling link,
the message (or set of messages) is retransmitted. MTP Level 2 is
equivalent to the OSI Data Link Layer.
+
+*MTP Level 3* provides message routing between signaling points in the SS7
network. MTP Level 3 re-routes traffic away from failed links and signaling
points and controls traffic when congestion occurs. MTP Level 3 is
equivalent to the OSI Network Layer.
+
+
+===== ISDN User Part (ISUP) =====
+The ISDN User Part (ISUP) defines the protocol used to set-up, manage, and
release trunk circuits that carry voice and data between terminating line
exchanges (e.g., between a calling party and a called party). ISUP is used
for both ISDN and non-ISDN calls. However, calls that originate and
terminate at the same switch do not use ISUP signaling.
+
+
+===== Telephone User Part (TUP) =====
+In some parts of the world (e.g., China, Brazil), the Telephone User Part
(TUP) is used to support basic call setup and tear-down. TUP handles analog
circuits only. In many countries, ISUP has replaced TUP for call management.
+
+
+===== Signaling Connection Control Part (SCCP) =====
+SCCP provides connectionless and connection-oriented network services and
global title translation (GTT) capabilities above MTP Level 3. A global
title is an address (e.g., a dialed 800 number, calling card number, or
mobile subscriber identification number) which is translated by SCCP into a
destination point code and subsystem number. A subsystem number uniquely
identifies an application at the destination signaling point. SCCP is used
as the transport layer for TCAP-based services.
+
+
+===== Transaction Capabilities Applications Part (TCAP) =====
+TCAP supports the exchange of non-circuit related data between
applications across the SS7 network using the SCCP connectionless service.
Queries and responses sent between SSPs and SCPs are carried in TCAP
messages. For example, an SSP sends a TCAP query to determine the routing
number associated with a dialed 800/888 number and to check the personal
identification number (PIN) of a calling card user. In mobile networks
(IS-41 and GSM), TCAP carries Mobile Application Part (MAP) messages sent
between mobile switches and databases to support user authentication,
equipment identification, and roaming.
=======================================
--- /SideBar.wiki Thu Jun 7 02:16:34 2012
+++ /SideBar.wiki Thu Jun 7 02:54:21 2012
@@ -3,3 +3,4 @@
* [Downloads Downloads]
*
[http://code.google.com/p/jss7/issues/list?can=1&q=Roadmap%3DDate+OR+Roadmap%3DIssue+OR+Roadmap%3DFix&sort=priority+version&groupby=version&colspec=Summary+Type+Status+ID&cells=tiles
Roadmap]
* [Contribute How to Contribute]
+ * [SS7Introduction SS7 Introduction]