It sounds like you either haven't obtained the B:: module, or there was
a compilation problem. You can try to get your current server up and
running
by commenting out the "PerlModule B:: ..." references, then try starting it
up.
Check on the Perl and Apache web sites (www.perl.org, www.apache.org) for
information
about properly incorporating/using modules with Apache and mod_perl. The
perl site
has PerlModules available for download if you need the code.
Hope this helps,
Laurie
Laurie Knox
AT&T - NETAC
[EMAIL PROTECTED]
-----Original Message-----
From: Gilberto Diaz [mailto:[EMAIL PROTECTED]]
Sent: Thursday, October 04, 2001 4:55 PM
To: [EMAIL PROTECTED]
Subject: shared libraries
Hello everybody
I'm triying to start a mod_perl apache in a Sun enterprise 450 with
solaris 2.6. Everything compile very well, but when I try to start the
server
the following error message is displayed.
**********************************************************************
cronos:/usr/local/apache/bin# ./apachectl start
Syntax error on line 72 of /usr/local/apache/conf/httpd.conf:
Can't load '/usr/local/lib/perl5/5.6.1/sun4-solaris/auto/B/B.so' for module
B: ld.so.1: /usr/local/apache/bin/httpd: fatal: relocation error: file
/usr/local/lib/perl5/5.6.1/sun4-solaris/auto/B/B.so: symbol main: referenced
symbol not found at /usr/local/lib/perl5/5.6.1/sun4-solaris/XSLoader.pm line
75.
at /usr/local/lib/perl5/5.6.1/sun4-solaris/B.pm line 284
Compilation failed in require at
/usr/local/lib/perl5/5.6.1/sun4-solaris/B/Terse.pm line 3.
BEGIN failed--compilation aborted at
/usr/local/lib/perl5/5.6.1/sun4-solaris/B/Terse.pm line 4.
Compilation failed in require at (eval 3) line 3.
./apachectl start: httpd could not be started
*****************************************************************
I have followed this set of instruction to compile everything
****************************************************************
> a. Unpack the apache and mod_perl distributions:
>
> gunzip apache_1.3.14.tar.gz
> tar -xvf apache_1.3.14.tar
> gunzip mod_perl-1.24_01.tar.gz
> tar -xvf mod_perl-1.24_01.tar
>
> b. Using the perl version 5.6.0 to compile into apache:
>
> cd mod_perl-1.24_01
> /path/to/perl5.6.0 Makefile.PL \
> < APACHE_SRC=../apache_1.3.14/src \
> < USE_APACI=1 \
> < EVERYTHING=1 \
> < DO_HTTPD=1
>
> make
> make install
>
> cd ../apache_1.3.14/src
> configure \
> < --prefix=/path/to/install/of/www \
> < --activate-module=src/modules/perl/libperl.a \
> < --enable-module=unique_id \
> < --enable-module=info
> make
> make install
>
> Editing httpd.conf (Apache/mod_perl installations only):
> Set these values in httpd.conf in addition to other normal configuration
> settings. NOTE: This is for Apache/mod_perl installations only. If you
> choose not to take advantage of this configuration, edit your httpd.conf
in
> the usual manner.
> # Do NOT adjust MaxRequestsPerChild or ExcessRequestsPerChild!
> MaxRequestsPerChild 50
> ExcessRequestsPerChild 1
> ExtendedStatus On
> # Do NOT set these next 4 settings too low, or too high or
> performance will suffer
> # Adjust according to hardware capabilities
> MinSpareServers 5
> MaxSpareServers 200
> StartServers 20
> MaxClients 256
>
> PerlTaintCheck Off
> PerlWarn Off
> # Do NOT turn PerlFreshRestart On
> PerlFreshRestart Off
>
> PerlModule B::Terse
> PerlModule B::LexInfo
> PerlModule B::Deparse
> PerlPassEnv TERM EDITOR NOCHANCE USER PERL5LIB
> PerlSetEnv KeyForPerlSetEnv OK
> PerlSetVar KeyForPerlSetVar OK
>
> # This sets @INC for the applications modules
> PerlRequire lib/perl/startup.pl
>
> Alias /perl/ "/path/to/server_root/lib/perl/"
> <Location /perl>
> SetHandler perl-script
> PerlHandler Apache::Registry::handler
> PerlInitHandler Apache::StatINC
> Options +ExecCGI
> PerlSendHeader On
> </Location>
>
> <Location /server-info>
> order deny,allow
> deny from all
> allow from add.your.ip.here
> SetHandler server info
> </Location>
>
> <Location /server-status>
> order deny,allow
> deny from all
> allow from add.your.ip.here
> SetHandler server status
> </Location>
>
> <Location /perl-status>
> order deny,allow
> deny from all
> allow from add.your.ip.here
> PerlSetVar StatusOptionsAll On
> PerlSetVar StatusDeparse On
> PerlSetVar StatusTerse On
> PerlSetVar StatusLexInfo On
> SetHandler perl-script
> PerlHandler +Apache::Status
> </Location>
>
> <Directory "/path/to/install/WoS">
> Options FollowSymLinks ExecCGI
> AllowOverride None
> Order allow,deny
> allow from all
> DirectoryIndex CIW.cgi
> <Files ~ "CIW\.cgi$">
> SetHandler perl-script
> PerlHandler Apache::Registry::handler
> Options +ExecCGI
> PerlSendHeader On
> </Files>
> </Directory>
****************************************************************
Thanks in advance for any help.
Best regards
Gilberto Diaz
CeCalCULA
--
Saludos/Best regards | e-mail: [EMAIL PROTECTED]
Gilberto Diaz (CeCalCULA) | [EMAIL PROTECTED]
Centro de Calculo Cientifico |
Universidad de Los Andes | http://www.cecalc.ula.ve/~gilberto
