Send Motion-user mailing list submissions to
[email protected]
To subscribe or unsubscribe via the World Wide Web, visit
https://lists.sourceforge.net/lists/listinfo/motion-user
or, via email, send a message with subject or body 'help' to
[email protected]
You can reach the person managing the list at
[email protected]
When replying, please edit your Subject line so it is more specific
than "Re: Contents of Motion-user digest..."
Today's Topics:
1. Re: unable to start motion after it worked for many weeks
(David Bate)
----------------------------------------------------------------------
Message: 1
Date: Mon, 28 May 2018 10:43:02 +0100
From: "David Bate" <[email protected]>
To: "'Motion discussion list'" <[email protected]>
Subject: Re: [Motion-user] unable to start motion after it worked for
many weeks
Message-ID: <[email protected]>
Content-Type: text/plain; charset="utf-8"
Jack,
I am not sure what you are responding to but I just put up a notice asking if
anyone knew about what could be wrong with my Pi camera and Motion software. I
eventually found that it was the camera cable being faulty. I have replaced it
and it is OK now.
Hope someone resolves your problem for you.
Regards
David Bate
1 Belgrave Place
Birkdale
Southport
Merseyside
PR8 2EF
01704 564 132
07836 328 614
From: jack bean <[email protected]>
Sent: 27 May 2018 23:18
To: Motion discussion list <[email protected]>
Subject: Re: [Motion-user] unable to start motion after it worked for many weeks
ok, but what does that have to do with my camera? it is a brand new usb camera,
and extension cable. it was working fine. the only thing i can think of is
updating the system somehow screwed up the settings or perhaps reinstalling
motion did. if i could box out the built in camera and use only the usb camera
before, then why not now? is there anything in the log file i am missing? it
cant be the camera, because i test it out with cheese to see if it even works,
and sure enough it is working flawlessly. so it is somewhere in the motion
settings, just where?
On Sat, May 26, 2018 at 2:12 PM, David Bate <[email protected]
<mailto:[email protected]> > wrote:
Jack,
Thanks for your reply. I have been using Motion on this Pi for over a year. It
is set up as a CCTV on the front of our house.
I bought another sd card yesterday and installed motion from"
https://jarlowrey.com/blog/rpi-with-motion.html"; today
Same problem.
Eventually found that the cable video cable is faulty
I now have a spare pi setup sd.
Incidentally I have to have Daemon turned off in the conf file.
My original Motion set up was using
"http://www.joakimlahtinen.se/2016/installing-motion-on-raspberry-pi-2-jessie/";
which still works fine since I changed the video cable.
Best Regards
David Bate
1 Belgrave Place
Birkdale
Southport
Merseyside
PR8 2EF
01704 564 132
07836 328 614
From: jack bean <[email protected] <mailto:[email protected]> >
Sent: 26 May 2018 19:49
To: [email protected]
<mailto:[email protected]>
Subject: [Motion-user] unable to start motion after it worked for many weeks
i had my share of hiccups starting it and getting it to record, until i just
started using sudo motion and then sudo killall motion to shut it down. it
recorded fine. i had dropbox linked to the record folder. the config file is
the same as it was when it worked, but now it will not work. motion starts, but
will not recors anything, no matter what i do, or how many times i jump up and
down in front of the camera. before it quit working it only took a bit of
movement to record video and stills. now it wont do anything. i also
reinstalled motion in synaptic.
here is the log file in case it has something i dont recognize as the issue.
[8831360] [NTC] [ALL] [May 26 13:01:59] motion_startup: Using log type (ALL)
log level (NTC)
[8831360] [NTC] [ALL] [May 26 13:01:59] become_daemon: Motion going to daemon
mode
[8831360] [NTC] [ALL] [May 26 13:01:59] become_daemon: Created process id file
/var/run/motion/motion.pid. Process ID is 31776
[8831360] [NTC] [ALL] [May 26 13:01:59] motion_startup: Motion running as
daemon process
[8831360] [NTC] [ENC] [May 26 13:01:59] ffmpeg_init: ffmpeg LIBAVCODEC_BUILD
3685476 LIBAVFORMAT_BUILD 3680357
[0] [NTC] [ALL] [May 26 13:01:59] main: Thread 1 is from
/home/stealth/.motion/motion.conf
[0] [NTC] [ALL] [May 26 13:01:59] main: Thread 1 is device: /dev/video1 input -1
[0] [NTC] [ALL] [May 26 13:01:59] main: Stream port 8081
[0] [NTC] [ALL] [May 26 13:01:59] main: Waiting for threads to finish, pid:
31776
[0] [NTC] [STR] [May 26 13:01:59] httpd_run: motion-httpd testing : IPV4 addr:
127.0.0.1 port: 8080
[0] [NTC] [STR] [May 26 13:01:59] httpd_run: motion-httpd Bound : IPV4 addr:
127.0.0.1 port: 8080
[0] [NTC] [STR] [May 26 13:01:59] httpd_run: motion-httpd/3.2.12+git20140228
running, accepting connections
[0] [NTC] [STR] [May 26 13:01:59] httpd_run: motion-httpd: waiting for data on
127.0.0.1 port TCP 8080
[1] [NTC] [ALL] [May 26 13:01:59] motion_init: Thread 1 started , motion
detection Enabled
[1] [NTC] [VID] [May 26 13:01:59] vid_v4lx_start: Using videodevice /dev/video1
and input -1
[1] [NTC] [VID] [May 26 13:01:59] v4l2_get_capability:
------------------------
cap.driver: "uvcvideo"
cap.card: "HP Webcam: HP Webcam"
cap.bus_info: "usb-0000:00:1d.7-5"
cap.capabilities=0x84200001
------------------------
[1] [NTC] [VID] [May 26 13:01:59] v4l2_get_capability: - VIDEO_CAPTURE
[1] [NTC] [VID] [May 26 13:01:59] v4l2_get_capability: - STREAMING
[1] [NTC] [VID] [May 26 13:01:59] v4l2_select_input: name = "Camera 1", type
0x00000002, status 00000000
[1] [NTC] [VID] [May 26 13:01:59] v4l2_select_input: - CAMERA
[1] [WRN] [VID] [May 26 13:01:59] v4l2_select_input: Device doesn't support
VIDIOC_G_STD
[1] [NTC] [VID] [May 26 13:01:59] v4l2_set_pix_format: Config palette index 17
(YU12) doesn't work.
[1] [NTC] [VID] [May 26 13:01:59] v4l2_set_pix_format: Supported palettes:
[1] [NTC] [VID] [May 26 13:01:59] v4l2_set_pix_format: (0) YUYV (YUYV 4:2:2)
[1] [NTC] [VID] [May 26 13:01:59] v4l2_set_pix_format: 0 - YUYV 4:2:2
(compressed : 0) (0x56595559)
[1] [NTC] [VID] [May 26 13:01:59] v4l2_set_pix_format Selected palette YUYV
[1] [NTC] [VID] [May 26 13:01:59] v4l2_do_set_pix_format: Testing palette YUYV
(320x240)
[1] [NTC] [VID] [May 26 13:01:59] v4l2_do_set_pix_format: Using palette YUYV
(320x240) bytesperlines 640 sizeimage 153600 colorspace 00000008
[1] [NTC] [VID] [May 26 13:01:59] v4l2_scan_controls: found control 0x00980900,
"Brightness", range -64,64
[1] [NTC] [VID] [May 26 13:01:59] v4l2_scan_controls: "Brightness", default
5, current 5
[1] [NTC] [VID] [May 26 13:01:59] v4l2_scan_controls: found control 0x00980901,
"Contrast", range 0,95
[1] [NTC] [VID] [May 26 13:01:59] v4l2_scan_controls: "Contrast", default
30, current 30
[1] [NTC] [VID] [May 26 13:01:59] v4l2_scan_controls: found control 0x00980902,
"Saturation", range 0,128
[1] [NTC] [VID] [May 26 13:01:59] v4l2_scan_controls: "Saturation", default
80, current 80
[1] [NTC] [VID] [May 26 13:01:59] v4l2_scan_controls: found control 0x00980903,
"Hue", range -40,40
[1] [NTC] [VID] [May 26 13:01:59] v4l2_scan_controls: "Hue", default 0,
current 0
[1] [NTC] [VID] [May 26 13:01:59] v4l2_scan_controls: found control 0x00980910,
"Gamma", range 72,500
[1] [NTC] [VID] [May 26 13:01:59] v4l2_scan_controls: "Gamma", default 120,
current 120
[1] [NTC] [VID] [May 26 13:01:59] v4l2_scan_controls: found control 0x00980913,
"Gain", range 0,100
[1] [NTC] [VID] [May 26 13:01:59] v4l2_scan_controls: "Gain", default 0,
current 0
[1] [NTC] [VID] [May 26 13:01:59] vid_v4lx_start: Using V4L2
[1] [NTC] [ALL] [May 26 13:01:59] image_ring_resize: Resizing pre_capture
buffer to 1 items
[1] [NTC] [STR] [May 26 13:02:00] http_bindsock: motion-stream testing : IPV4
addr: 127.0.0.1 port: 8081
[1] [NTC] [STR] [May 26 13:02:00] http_bindsock: motion-stream Bound : IPV4
addr: 127.0.0.1 port: 8081
[1] [NTC] [ALL] [May 26 13:02:00] motion_init: Started motion-stream server in
port 8081 auth Disabled
[1] [NTC] [ALL] [May 26 13:05:05] motion_loop: End of event 1
[1] [NTC] [ALL] [May 26 13:05:05] motion_loop: Thread exiting
[1] [NTC] [STR] [May 26 13:05:05] stream_stop: Closing motion-stream listen
socket & active motion-stream sockets
[1] [NTC] [STR] [May 26 13:05:05] stream_stop: Closed motion-stream listen
socket & active motion-stream sockets
[1] [NTC] [VID] [May 26 13:05:05] vid_close: Closing video device /dev/video1
[0] [NTC] [ALL] [May 26 13:05:05] main: Threads finished
[0] [NTC] [STR] [May 26 13:05:05] httpd_run: motion-httpd - Finishing
[0] [NTC] [STR] [May 26 13:05:05] httpd_run: motion-httpd Closing
[0] [NTC] [STR] [May 26 13:05:05] motion_web_control: motion-httpd thread exit
[0] [NTC] [ALL] [May 26 13:05:06] main: Motion terminating
[0] [NTC] [ALL] [May 26 13:05:06] motion_remove_pid: Removed process id file
(pid file).
[0] [NTC] [ALL] [May 26 13:05:06] motion_remove_pid: Closing logfile
(/var/log/motion/motion.log).
[10338688] [NTC] [ALL] [May 26 13:18:48] motion_startup: Using log type (ALL)
log level (NTC)
[10338688] [NTC] [ALL] [May 26 13:18:48] become_daemon: Motion going to daemon
mode
[10338688] [NTC] [ALL] [May 26 13:18:48] become_daemon: Created process id file
/var/run/motion/motion.pid. Process ID is 1746
[10338688] [NTC] [ALL] [May 26 13:18:48] motion_startup: Motion running as
daemon process
[10338688] [NTC] [ENC] [May 26 13:18:48] ffmpeg_init: ffmpeg LIBAVCODEC_BUILD
3685476 LIBAVFORMAT_BUILD 3680357
[0] [NTC] [ALL] [May 26 13:18:48] main: Thread 1 is from
/home/stealth/.motion/motion.conf
[0] [NTC] [ALL] [May 26 13:18:48] main: Thread 1 is device: /dev/video1 input -1
[0] [NTC] [ALL] [May 26 13:18:48] main: Stream port 8081
[0] [NTC] [ALL] [May 26 13:18:48] main: Waiting for threads to finish, pid: 1746
[0] [NTC] [STR] [May 26 13:18:48] httpd_run: motion-httpd testing : IPV4 addr:
127.0.0.1 port: 8080
[0] [NTC] [STR] [May 26 13:18:48] httpd_run: motion-httpd Bound : IPV4 addr:
127.0.0.1 port: 8080
[0] [NTC] [STR] [May 26 13:18:48] httpd_run: motion-httpd/3.2.12+git20140228
running, accepting connections
[0] [NTC] [STR] [May 26 13:18:48] httpd_run: motion-httpd: waiting for data on
127.0.0.1 port TCP 8080
[1] [NTC] [ALL] [May 26 13:18:48] motion_init: Thread 1 started , motion
detection Enabled
[1] [NTC] [VID] [May 26 13:18:48] vid_v4lx_start: Using videodevice /dev/video1
and input -1
[1] [NTC] [VID] [May 26 13:18:48] v4l2_get_capability:
------------------------
cap.driver: "uvcvideo"
cap.card: "HP Webcam: HP Webcam"
cap.bus_info: "usb-0000:00:1d.7-5"
cap.capabilities=0x84200001
------------------------
[1] [NTC] [VID] [May 26 13:18:48] v4l2_get_capability: - VIDEO_CAPTURE
[1] [NTC] [VID] [May 26 13:18:48] v4l2_get_capability: - STREAMING
[1] [NTC] [VID] [May 26 13:18:48] v4l2_select_input: name = "Camera 1", type
0x00000002, status 00000000
[1] [NTC] [VID] [May 26 13:18:48] v4l2_select_input: - CAMERA
[1] [WRN] [VID] [May 26 13:18:48] v4l2_select_input: Device doesn't support
VIDIOC_G_STD
[1] [NTC] [VID] [May 26 13:18:48] v4l2_set_pix_format: Config palette index 17
(YU12) doesn't work.
[1] [NTC] [VID] [May 26 13:18:48] v4l2_set_pix_format: Supported palettes:
[1] [NTC] [VID] [May 26 13:18:48] v4l2_set_pix_format: (0) YUYV (YUYV 4:2:2)
[1] [NTC] [VID] [May 26 13:18:48] v4l2_set_pix_format: 0 - YUYV 4:2:2
(compressed : 0) (0x56595559)
[1] [NTC] [VID] [May 26 13:18:48] v4l2_set_pix_format Selected palette YUYV
[1] [NTC] [VID] [May 26 13:18:48] v4l2_do_set_pix_format: Testing palette YUYV
(320x240)
[1] [NTC] [VID] [May 26 13:18:48] v4l2_do_set_pix_format: Using palette YUYV
(320x240) bytesperlines 640 sizeimage 153600 colorspace 00000008
[1] [NTC] [VID] [May 26 13:18:48] v4l2_scan_controls: found control 0x00980900,
"Brightness", range -64,64
[1] [NTC] [VID] [May 26 13:18:48] v4l2_scan_controls: "Brightness", default
5, current 5
[1] [NTC] [VID] [May 26 13:18:48] v4l2_scan_controls: found control 0x00980901,
"Contrast", range 0,95
[1] [NTC] [VID] [May 26 13:18:48] v4l2_scan_controls: "Contrast", default
30, current 30
[1] [NTC] [VID] [May 26 13:18:48] v4l2_scan_controls: found control 0x00980902,
"Saturation", range 0,128
[1] [NTC] [VID] [May 26 13:18:48] v4l2_scan_controls: "Saturation", default
80, current 80
[1] [NTC] [VID] [May 26 13:18:48] v4l2_scan_controls: found control 0x00980903,
"Hue", range -40,40
[1] [NTC] [VID] [May 26 13:18:48] v4l2_scan_controls: "Hue", default 0,
current 0
[1] [NTC] [VID] [May 26 13:18:48] v4l2_scan_controls: found control 0x00980910,
"Gamma", range 72,500
[1] [NTC] [VID] [May 26 13:18:48] v4l2_scan_controls: "Gamma", default 120,
current 120
[1] [NTC] [VID] [May 26 13:18:48] v4l2_scan_controls: found control 0x00980913,
"Gain", range 0,100
[1] [NTC] [VID] [May 26 13:18:48] v4l2_scan_controls: "Gain", default 0,
current 0
[1] [NTC] [VID] [May 26 13:18:48] vid_v4lx_start: Using V4L2
[1] [NTC] [ALL] [May 26 13:18:48] image_ring_resize: Resizing pre_capture
buffer to 1 items
[1] [NTC] [STR] [May 26 13:18:49] http_bindsock: motion-stream testing : IPV4
addr: 127.0.0.1 port: 8081
[1] [NTC] [STR] [May 26 13:18:49] http_bindsock: motion-stream Bound : IPV4
addr: 127.0.0.1 port: 8081
[1] [NTC] [ALL] [May 26 13:18:49] motion_init: Started motion-stream server in
port 8081 auth Disabled
[1] [NTC] [ALL] [May 26 13:21:07] motion_loop: End of event 1
[1] [NTC] [ALL] [May 26 13:21:07] motion_loop: Thread exiting
[1] [NTC] [STR] [May 26 13:21:07] stream_stop: Closing motion-stream listen
socket & active motion-stream sockets
[1] [NTC] [STR] [May 26 13:21:07] stream_stop: Closed motion-stream listen
socket & active motion-stream sockets
[1] [NTC] [VID] [May 26 13:21:07] vid_close: Closing video device /dev/video1
[0] [NTC] [ALL] [May 26 13:21:07] main: Threads finished
[0] [NTC] [STR] [May 26 13:21:07] httpd_run: motion-httpd - Finishing
[0] [NTC] [STR] [May 26 13:21:07] httpd_run: motion-httpd Closing
[0] [NTC] [STR] [May 26 13:21:07] motion_web_control: motion-httpd thread exit
[0] [NTC] [ALL] [May 26 13:21:08] main: Motion terminating
[0] [NTC] [ALL] [May 26 13:21:08] motion_remove_pid: Removed process id file
(pid file).
[0] [NTC] [ALL] [May 26 13:21:08] motion_remove_pid: Closing logfile
(/var/log/motion/motion.log).
where it says devices, it indicates it is trying to use the internal webcam
instead of the external one, but why did it revert to that when i specifically
changed it in the config file?
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org! http://sdm.link/slashdot
_______________________________________________
Motion-user mailing list
[email protected] <mailto:[email protected]>
https://lists.sourceforge.net/lists/listinfo/motion-user
https://motion-project.github.io/
Unsubscribe: https://lists.sourceforge.net/lists/options/motion-user
-------------- next part --------------
An HTML attachment was scrubbed...
------------------------------
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org! http://sdm.link/slashdot
------------------------------
Subject: Digest Footer
_______________________________________________
Motion-user mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/motion-user
------------------------------
End of Motion-user Digest, Vol 143, Issue 30
********************************************
