Send Motion-user mailing list submissions to
[email protected]
To subscribe or unsubscribe via the World Wide Web, visit
https://lists.sourceforge.net/lists/listinfo/motion-user
or, via email, send a message with subject or body 'help' to
[email protected]
You can reach the person managing the list at
[email protected]
When replying, please edit your Subject line so it is more specific
than "Re: Contents of Motion-user digest..."
Today's Topics:
1. Re: Trouble getting 2 USB ELP cameras going on rPi ( just 1
works fine ) (John D. Gwinner)
2. Re: Anyone using Wyze cameras? (Tom Kennelly)
3. Re: Anyone using Wyze cameras? (Alan McKay)
4. Re: Anyone using Wyze cameras? (Jake Stride)
----------------------------------------------------------------------
Message: 1
Date: Sun, 30 Dec 2018 17:57:15 +0000
From: "John D. Gwinner" <[email protected]>
To: Motion discussion list <[email protected]>
Subject: Re: [Motion-user] Trouble getting 2 USB ELP cameras going on
rPi ( just 1 works fine )
Message-ID:
<sn6pr01mb371148151efde3e8c1b01437c3...@sn6pr01mb3711.prod.exchangelabs.com>
Content-Type: text/plain; charset="iso-8859-1"
USB3.0 controller would be capable of more bandwidth with 2 USB 2.0 clients
running full USB 2.0 bandwidth than a USB 2.0 controller, would be my guess.
Total bandwidth *per controller* is the limit, and if you're saturating a
single line, adding another would have to go through the same pipe.
USB 3.0 is a lot better. The problem with USB 3.0 is that very few single board
computers have a USB 3.0 interface; especially the Raspberry Pi's.
I know, I checked *all* of them a while ago. There are a few SoC (System on
Chip) boards that do have USB 3.0, if you're interested I'll update you.
??????????????? == John ==
John Gwinner .
cto4you.com
------------------------------
Message: 2
Date: Sun, 30 Dec 2018 16:12:07 -0500
From: Tom Kennelly <[email protected]>
To: Motion discussion list <[email protected]>
Subject: Re: [Motion-user] Anyone using Wyze cameras?
Message-ID:
<[email protected]>
Content-Type: text/plain; charset=utf-8
Yes, I am using two 720p WiFi Waze camera?s with OpenIP. With the V2 cameras
the automated switch to night mode does not work however.
Tom
> On Dec 30, 2018, at 12:52 PM, Alan McKay <[email protected]> wrote:
>
> Hey folks is anyone using the Wyze cameras and in particular with the
> open source firmware installed?
>
> Or if you are not using the open source FW is there a way to get at
> the stream to feed it into motion or MotionEye?
>
> --
> "You should sit in nature for 20 minutes a day.
> Unless you are busy, then you should sit for an hour"
> - Zen Proverb
>
>
> _______________________________________________
> Motion-user mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/motion-user
> https://motion-project.github.io/
>
> Unsubscribe: https://lists.sourceforge.net/lists/options/motion-user
------------------------------
Message: 3
Date: Sun, 30 Dec 2018 16:33:35 -0500
From: Alan McKay <[email protected]>
To: Motion discussion list <[email protected]>
Subject: Re: [Motion-user] Anyone using Wyze cameras?
Message-ID:
<CAH8ZPG=bpdrx0gz9mc_ajwmoeswskmrwez2sagzyor7lxs7...@mail.gmail.com>
Content-Type: text/plain; charset="UTF-8"
> With the V2 cameras the automated switch to night mode does not work however
Can you switch manually at least?
------------------------------
Message: 4
Date: Mon, 31 Dec 2018 06:04:28 +0800
From: Jake Stride <[email protected]>
To: Motion discussion list <[email protected]>
Subject: Re: [Motion-user] Anyone using Wyze cameras?
Message-ID:
<CAOO87zNW-yZTJt0CWREgkpHLw_VxDpSZj5+3=z89eba6nck...@mail.gmail.com>
Content-Type: text/plain; charset="utf-8"
I am using the Xiaomi ones and the software mode works for night vision
On Mon., 31 Dec. 2018, 05:34 Alan McKay <[email protected] wrote:
> > With the V2 cameras the automated switch to night mode does not work
> however
>
> Can you switch manually at least?
>
>
> _______________________________________________
> Motion-user mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/motion-user
> https://motion-project.github.io/
>
> Unsubscribe: https://lists.sourceforge.net/lists/options/motion-user
>
-------------- next part --------------
An HTML attachment was scrubbed...
------------------------------
------------------------------
Subject: Digest Footer
_______________________________________________
Motion-user mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/motion-user
------------------------------
End of Motion-user Digest, Vol 150, Issue 13
********************************************
