Send Motion-user mailing list submissions to
[email protected]
To subscribe or unsubscribe via the World Wide Web, visit
https://lists.sourceforge.net/lists/listinfo/motion-user
or, via email, send a message with subject or body 'help' to
[email protected]
You can reach the person managing the list at
[email protected]
When replying, please edit your Subject line so it is more specific
than "Re: Contents of Motion-user digest..."
Today's Topics:
1. Re: Can't pause motion detection at startup (MrDave)
2. Re: Can't pause motion detection at startup (Postgarage Graz IT)
----------------------------------------------------------------------
Message: 1
Date: Tue, 6 Dec 2022 07:11:47 -0700
From: MrDave <[email protected]>
To: [email protected]
Subject: Re: [Motion-user] Can't pause motion detection at startup
Message-ID: <[email protected]>
Content-Type: text/plain; charset="utf-8"; Format="flowed"
Thanks for reporting.? The temporary workaround that should work is to
specify it in the configuration file.? (When it was added as a new
parameter it ignored the command line option.)
As a side note.....the log also indicates? "Unable to start MHD".? You
may need a reboot to fix that...or you may be running multiple instances
of Motion....If Motion continues with the message that it is unable to
start MHD, there will not be a method to "un-pause" after it starts.?
(MHD is the web interface.)
On 12/6/2022 4:46 AM, tosiara wrote:
> Hi, I also reproduced this. Created an issue:
>
> https://github.com/Motion-Project/motion/issues/1600
>
> On Tue, Dec 6, 2022 at 1:26 PM Postgarage Graz IT via Motion-user
> <[email protected]> wrote:
>
> Hello!
>
> I'm having the problem, that when I startup motion there's always an
> immediate event detected.
> So I want to start motion with the "-m" parameter but it's either
> ignored or I completely missunderstand its usage.
>
> I installed motion by using the
> pi_bullseye_motion_4.5.0-1_armhf.deb packages from the release
> page and
> I'm running it on Raspbian 11.5.
>
> Thanks in advance
>
>
> pi@minerva:~$ motion -n -m
> [0:motion] [NTC] [ALL] conf_load: Processing thread 0 - config file
> /etc/motion/motion.conf
> [0:motion] [NTC] [ALL] motion_startup: Logging to syslog
> [0:motion] [NTC] [STR] webu_strm_ntc: Started camera 0 stream on
> port 8081
> [0:motion] [NTC] [STR] webu_start_ctrl: Starting webcontrol on
> port 8080
> [0:motion] [NTC] [STR] webu_start_ctrl: Unable to start MHD
> [0:motion] [NTC] [ENC] ffmpeg_global_init: ffmpeg libavcodec version
> 58.91.100 libavformat version 58.45.100
> [0:motion] [NTC] [ALL] motion_startup: Using log type (ALL) log
> level (NTC)
> [0:motion] [NTC] [STR] webu_start_strm: Starting all camera
> streams on
> port 8081
> [0:motion] [NTC] [STR] webu_strm_ntc: Started camera 0 stream on
> port 8081
> [0:motion] [NTC] [STR] webu_start_ctrl: Starting webcontrol on
> port 8080
> [0:motion] [NTC] [STR] webu_start_ctrl: Unable to start MHD
> [0:motion] [NTC] [ENC] ffmpeg_global_init: ffmpeg libavcodec version
> 58.91.100 libavformat version 58.45.100
> [0:motion] [NTC] [ALL] translate_init: Language: English
> [0:motion] [NTC] [ALL] motion_start_thread: Camera ID: 0 is from
> /etc/motion/motion.conf
> [0:motion] [NTC] [ALL] motion_start_thread: Camera ID: 0 Camera Name:
> (null) Service: rtsp:
> [0:motion] [NTC] [ALL] main: Waiting for threads to finish, pid: 6332
> [1:ml1] [NTC] [ALL] motion_init: Camera 0 started: motion
> detection Enabled
> [1:ml1] [NTC] [VID] vid_start: Opening Netcam RTSP
> [1:ml1] [NTC] [NET] motion_init: Substream not available. Image sizes
> not modulo 16.
> [1:ml1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer
> to 1
> items
> [2:nc2] [NTC] [NET] netcam_rtsp_handler: norm: Camera handler
> thread [2]
> started
> [2:nc2] [NTC] [NET] netcam_rtsp_connect: norm: Camera ((null))
> connected
> [1:ml1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer
> to 4
> items
> [1:ml1] [NTC] [ALL] motion_detected: Motion detected - starting
> event 1.
> [1:ml1] [NTC] [EVT] event_newfile: Writing movie to file:
> /home/pi/motion-images/0-01-2022-12-06-11-37-09.mkv
> [1:ml1] [NTC] [EVT] event_newfile: Writing image to file:
> /home/pi/motion-images/2022-12-06-11-37-11-00.jpg
> [1:ml1] [NTC] [ALL] mlp_actions: End of event 1
> ^C[1:ml1] [NTC] [ALL] motion_loop: Thread exiting
> [1:ml1] [NTC] [NET] netcam_rtsp_cleanup: Normal resolution: Shut down
> complete.
> [0:motion] [NTC] [ALL] main: Threads finished
> [0:motion] [NTC] [ALL] main: Motion terminating
>
>
> _______________________________________________
> Motion-user mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/motion-user
> https://motion-project.github.io/
>
> Unsubscribe: https://lists.sourceforge.net/lists/options/motion-user
>
>
>
> _______________________________________________
> Motion-user mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/motion-user
> https://motion-project.github.io/
>
> Unsubscribe:https://lists.sourceforge.net/lists/options/motion-user
-------------- next part --------------
An HTML attachment was scrubbed...
------------------------------
Message: 2
Date: Tue, 6 Dec 2022 16:10:06 +0100
From: Postgarage Graz IT <[email protected]>
To: [email protected]
Subject: Re: [Motion-user] Can't pause motion detection at startup
Message-ID: <[email protected]>
Content-Type: text/plain; charset=UTF-8; format=flowed
On 12/6/22 15:11, MrDave wrote:
> Thanks for reporting.? The temporary workaround that should work is to
> specify it in the configuration file.? (When it was added as a new
> parameter it ignored the command line option.)
Ahh, thanks! That works and solves my problem - it's even better,
otherwise I would have had to modify how systemd starts the daemon. I
wasn't aware that I can set it in the config file too.
> As a side note.....the log also indicates? "Unable to start MHD".? You
> may need a reboot to fix that...or you may be running multiple instances
> of Motion....If Motion continues with the message that it is unable to
> start MHD, there will not be a method to "un-pause" after it starts.
> (MHD is the web interface.)
Didn't notice that yet, but it was just an already used port.
>
>
> On 12/6/2022 4:46 AM, tosiara wrote:
>> Hi, I also reproduced this. Created an issue:
>>
>> https://github.com/Motion-Project/motion/issues/1600
>>
>> On Tue, Dec 6, 2022 at 1:26 PM Postgarage Graz IT via Motion-user
>> <[email protected]> wrote:
>>
>> ??? Hello!
>>
>> ??? I'm having the problem, that when I startup motion there's always an
>> ??? immediate event detected.
>> ??? So I want to start motion with the "-m" parameter but it's either
>> ??? ignored or I completely missunderstand its usage.
>>
>> ??? I installed motion by using the
>> ??? pi_bullseye_motion_4.5.0-1_armhf.deb packages from the release
>> ??? page and
>> ??? I'm running it on Raspbian 11.5.
>>
>> ??? Thanks in advance
>>
>>
>> ??? pi@minerva:~$ motion -n -m
>> ??? [0:motion] [NTC] [ALL] conf_load: Processing thread 0 - config file
>> ??? /etc/motion/motion.conf
>> ??? [0:motion] [NTC] [ALL] motion_startup: Logging to syslog
>> ??? [0:motion] [NTC] [STR] webu_strm_ntc: Started camera 0 stream on
>> ??? port 8081
>> ??? [0:motion] [NTC] [STR] webu_start_ctrl: Starting webcontrol on
>> ??? port 8080
>> ??? [0:motion] [NTC] [STR] webu_start_ctrl: Unable to start MHD
>> ??? [0:motion] [NTC] [ENC] ffmpeg_global_init: ffmpeg libavcodec version
>> ??? 58.91.100 libavformat version 58.45.100
>> ??? [0:motion] [NTC] [ALL] motion_startup: Using log type (ALL) log
>> ??? level (NTC)
>> ??? [0:motion] [NTC] [STR] webu_start_strm: Starting all camera
>> ??? streams on
>> ??? port 8081
>> ??? [0:motion] [NTC] [STR] webu_strm_ntc: Started camera 0 stream on
>> ??? port 8081
>> ??? [0:motion] [NTC] [STR] webu_start_ctrl: Starting webcontrol on
>> ??? port 8080
>> ??? [0:motion] [NTC] [STR] webu_start_ctrl: Unable to start MHD
>> ??? [0:motion] [NTC] [ENC] ffmpeg_global_init: ffmpeg libavcodec version
>> ??? 58.91.100 libavformat version 58.45.100
>> ??? [0:motion] [NTC] [ALL] translate_init: Language: English
>> ??? [0:motion] [NTC] [ALL] motion_start_thread: Camera ID: 0 is from
>> ??? /etc/motion/motion.conf
>> ??? [0:motion] [NTC] [ALL] motion_start_thread: Camera ID: 0 Camera Name:
>> ??? (null) Service: rtsp:
>> ??? [0:motion] [NTC] [ALL] main: Waiting for threads to finish, pid: 6332
>> ??? [1:ml1] [NTC] [ALL] motion_init: Camera 0 started: motion
>> ??? detection Enabled
>> ??? [1:ml1] [NTC] [VID] vid_start: Opening Netcam RTSP
>> ??? [1:ml1] [NTC] [NET] motion_init: Substream not available. Image sizes
>> ??? not modulo 16.
>> ??? [1:ml1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer
>> ??? to 1
>> ??? items
>> ??? [2:nc2] [NTC] [NET] netcam_rtsp_handler: norm: Camera handler
>> ??? thread [2]
>> ??? started
>> ??? [2:nc2] [NTC] [NET] netcam_rtsp_connect: norm: Camera ((null))
>> ??? connected
>> ??? [1:ml1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer
>> ??? to 4
>> ??? items
>> ??? [1:ml1] [NTC] [ALL] motion_detected: Motion detected - starting
>> ??? event 1.
>> ??? [1:ml1] [NTC] [EVT] event_newfile: Writing movie to file:
>> ??? /home/pi/motion-images/0-01-2022-12-06-11-37-09.mkv
>> ??? [1:ml1] [NTC] [EVT] event_newfile: Writing image to file:
>> ??? /home/pi/motion-images/2022-12-06-11-37-11-00.jpg
>> ??? [1:ml1] [NTC] [ALL] mlp_actions: End of event 1
>> ??? ^C[1:ml1] [NTC] [ALL] motion_loop: Thread exiting
>> ??? [1:ml1] [NTC] [NET] netcam_rtsp_cleanup: Normal resolution: Shut down
>> ??? complete.
>> ??? [0:motion] [NTC] [ALL] main: Threads finished
>> ??? [0:motion] [NTC] [ALL] main: Motion terminating
>>
>>
>> ??? _______________________________________________
>> ??? Motion-user mailing list
>> ??? [email protected]
>> ??? https://lists.sourceforge.net/lists/listinfo/motion-user
>> ??? https://motion-project.github.io/
>>
>> ??? Unsubscribe: https://lists.sourceforge.net/lists/options/motion-user
>>
>>
>>
>> _______________________________________________
>> Motion-user mailing list
>> [email protected]
>> https://lists.sourceforge.net/lists/listinfo/motion-user
>> https://motion-project.github.io/
>>
>> Unsubscribe:https://lists.sourceforge.net/lists/options/motion-user
>
>
> _______________________________________________
> Motion-user mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/motion-user
> https://motion-project.github.io/
>
> Unsubscribe: https://lists.sourceforge.net/lists/options/motion-user
------------------------------
------------------------------
Subject: Digest Footer
_______________________________________________
Motion-user mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/motion-user
------------------------------
End of Motion-user Digest, Vol 196, Issue 5
*******************************************
