Greetings, I have been attempting to get a Netgear WG302, firmware 3.0.7 to graph under MRTG. I am running MRTG/RRDTool/Routers2 with great success (thanks once again to all who helped make these sessional pieces of software) but I can only get empty graphs with this device. I used cfgmaker to make the initial Config, but all interfaces were remarked out, so I enabled all of them in the Config, but all come up empty. Does anyone know of a special OID that needs to be used, on their website they say it supports MIB I & II. below is the config, names & ip's changed to protect the guilty... ------------------------------------------------------------------------ -- ###################################################################### # System: Rm25AP # Description: NETGEAR WG302 3.0.7 # Contact: # Location: ###################################################################### ### Interface 1 >> Descr: 'lo' | Name: '' | Ip: '127.0.0.1' | Eth: '' ### ### The following interface is commented out because: ### * has a speed of which makes no sense ### * got 'Received SNMP response with error code ### error status: noSuchName ### index 1 (OID: 1.3.6.1.2.1.2.2.1.10.1) ### SNMPv1_Session (remote host: "1.1.1.1" [1.1.1.1].161) ### community: "<something-here>" ### request ID: 36302426 ### PDU bufsize: 8000 bytes ### timeout: 2s ### retries: 5 ### backoff: 1)' from interface when trying to query # Target[1.1.1.1_1]: 1:<something-here>@1.1.1.1: SetEnv[1.1.1.1_1]: MRTG_INT_IP="127.0.0.1" MRTG_INT_DESCR="lo" MaxBytes[1.1.1.1_1]: 12500000 Title[1.1.1.1_1]: Traffic Analysis for 1 -- Rm25AP PageTop[1.1.1.1_1]: <H1>Traffic Analysis for 1 -- Rm25AP</H1> # <TABLE> # <TR><TD>System:</TD> <TD>Rm25AP in </TD></TR> # <TR><TD>Maintainer:</TD> <TD></TD></TR> # <TR><TD>Description:</TD><TD>lo </TD></TR> # <TR><TD>ifType:</TD> <TD>Other (1)</TD></TR> # <TR><TD>ifName:</TD> <TD></TD></TR> # <TR><TD>Max Speed:</TD> <TD>0.0 Bytes/s</TD></TR> # <TR><TD>Ip:</TD> <TD>127.0.0.1 (localhost.localdomain)</TD></TR> # </TABLE>
### Interface 2 >> Descr: 'ixp0' | Name: '' | Ip: '0.0.0.0' | Eth: '' ### ### The following interface is commented out because: ### * has a speed of which makes no sense ### * got 'Received SNMP response with error code ### error status: noSuchName ### index 1 (OID: 1.3.6.1.2.1.2.2.1.10.2) ### SNMPv1_Session (remote host: "1.1.1.1" [1.1.1.1].161) ### community: "<something-here>" ### request ID: 36302427 ### PDU bufsize: 8000 bytes ### timeout: 2s ### retries: 5 ### backoff: 1)' from interface when trying to query # # Target[1.1.1.1_2]: 2:<something-here>@1.1.1.1: # SetEnv[1.1.1.1_2]: MRTG_INT_IP="0.0.0.0" MRTG_INT_DESCR="ixp0" # MaxBytes[1.1.1.1_2]: 0 # Title[1.1.1.1_2]: Traffic Analysis for 2 -- Rm25AP # PageTop[1.1.1.1_2]: <H1>Traffic Analysis for 2 -- Rm25AP</H1> # <TABLE> # <TR><TD>System:</TD> <TD>Rm25AP in </TD></TR> # <TR><TD>Maintainer:</TD> <TD></TD></TR> # <TR><TD>Description:</TD><TD>ixp0 </TD></TR> # <TR><TD>ifType:</TD> <TD>Other (1)</TD></TR> # <TR><TD>ifName:</TD> <TD></TD></TR> # <TR><TD>Max Speed:</TD> <TD>0.0 Bytes/s</TD></TR> # <TR><TD>Ip:</TD> <TD>0.0.0.0 ()</TD></TR> # </TABLE> ### Interface 3 >> Descr: 'ixp1' | Name: '' | Ip: '' | Eth: '00-02-b3-02-02-02' ### ### The following interface is commented out because: ### * it is administratively DOWN ### * it is operationally DOWN ### * has a speed of which makes no sense ### * got 'Received SNMP response with error code ### error status: noSuchName ### index 1 (OID: 1.3.6.1.2.1.2.2.1.10.3) ### SNMPv1_Session (remote host: "1.1.1.1" [1.1.1.1].161) ### community: "<something-here>" ### request ID: 36302428 ### PDU bufsize: 8000 bytes ### timeout: 2s ### retries: 5 ### backoff: 1)' from interface when trying to query # # Target[1.1.1.1_3]: 3:<something-here>@1.1.1.1: # SetEnv[1.1.1.1_3]: MRTG_INT_IP="" MRTG_INT_DESCR="ixp1" # MaxBytes[1.1.1.1_3]: 0 # Title[1.1.1.1_3]: Traffic Analysis for 3 -- Rm25AP # PageTop[1.1.1.1_3]: <H1>Traffic Analysis for 3 -- Rm25AP</H1> # <TABLE> # <TR><TD>System:</TD> <TD>Rm25AP in </TD></TR> # <TR><TD>Maintainer:</TD> <TD></TD></TR> # <TR><TD>Description:</TD><TD>ixp1 </TD></TR> # <TR><TD>ifType:</TD> <TD>Other (1)</TD></TR> # <TR><TD>ifName:</TD> <TD></TD></TR> # <TR><TD>Max Speed:</TD> <TD>0.0 Bytes/s</TD></TR> # </TABLE> ### Interface 4 >> Descr: 'eth0' | Name: '' | Ip: '' | Eth: '' ### ### The following interface is commented out because: ### * has a speed of which makes no sense ### * got 'Received SNMP response with error code ### error status: noSuchName ### index 1 (OID: 1.3.6.1.2.1.2.2.1.10.4) ### SNMPv1_Session (remote host: "1.1.1.1" [1.1.1.1].161) ### community: "<something-here>" ### request ID: 36302429 ### PDU bufsize: 8000 bytes ### timeout: 2s ### retries: 5 ### backoff: 1)' from interface when trying to query # # Target[1.1.1.1_4]: 4:<something-here>@1.1.1.1: # SetEnv[1.1.1.1_4]: MRTG_INT_IP="" MRTG_INT_DESCR="eth0" # MaxBytes[1.1.1.1_4]: 0 # Title[1.1.1.1_4]: Traffic Analysis for 4 -- Rm25AP # PageTop[1.1.1.1_4]: <H1>Traffic Analysis for 4 -- Rm25AP</H1> # <TABLE> # <TR><TD>System:</TD> <TD>Rm25AP in </TD></TR> # <TR><TD>Maintainer:</TD> <TD></TD></TR> # <TR><TD>Description:</TD><TD>eth0 </TD></TR> # <TR><TD>ifType:</TD> <TD>Other (1)</TD></TR> # <TR><TD>ifName:</TD> <TD></TD></TR> # <TR><TD>Max Speed:</TD> <TD>0.0 Bytes/s</TD></TR> # </TABLE> ### Interface 5 >> Descr: 'bridge0' | Name: '' | Ip: '1.1.1.1' | Eth: '' ### ### The following interface is commented out because: ### * has a speed of which makes no sense ### * got 'Received SNMP response with error code ### error status: noSuchName ### index 1 (OID: 1.3.6.1.2.1.2.2.1.10.5) ### SNMPv1_Session (remote host: "1.1.1.1" [1.1.1.1].161) ### community: "<something-here>" ### request ID: 36302430 ### PDU bufsize: 8000 bytes ### timeout: 2s ### retries: 5 ### backoff: 1)' from interface when trying to query # Target[1.1.1.1_5]: 5:<something-here>@1.1.1.1: SetEnv[1.1.1.1_5]: MRTG_INT_IP="1.1.1.1" MRTG_INT_DESCR="bridge0" MaxBytes[1.1.1.1_5]: 12500000 Title[1.1.1.1_5]: Traffic Analysis for 5 -- Rm25AP PageTop[1.1.1.1_5]: <H1>Traffic Analysis for 5 -- Rm25AP</H1> # <TABLE> # <TR><TD>System:</TD> <TD>Rm25AP in </TD></TR> # <TR><TD>Maintainer:</TD> <TD></TD></TR> # <TR><TD>Description:</TD><TD>bridge0 </TD></TR> # <TR><TD>ifType:</TD> <TD>Other (1)</TD></TR> # <TR><TD>ifName:</TD> <TD></TD></TR> # <TR><TD>Max Speed:</TD> <TD>0.0 Bytes/s</TD></TR> # <TR><TD>Ip:</TD> <TD>1.1.1.1 ()</TD></TR> # </TABLE> ------------------------------------------------------------------------ ------------------------------------------------- Cheers ... Ash Ashley Morrison, MCSE MCP DCE Network Administrator St. Michael's College 15 Mitton Ave Henley Beach, SA, 5022 Ph: +61 8 8356 5966 Internet: www.smc.sa.edu.au <http://www.smc.sa.edu.au/> -- Unsubscribe mailto:[EMAIL PROTECTED] Archive http://lists.ee.ethz.ch/mrtg FAQ http://faq.mrtg.org Homepage http://www.mrtg.org WebAdmin http://lists.ee.ethz.ch/lsg2.cgi
