Hello all, This works.....thanks a lot, i checked every thing but missed on the most evident one.
@Michele: I inserted the Ip address of the swicth which was missing in my .cfg file. Thanks a lot for your time and help... :) :) --Anjini On Wed, Aug 27, 2008 at 10:59 AM, Anson Rinesmith < [EMAIL PROTECTED]> wrote: > So replace the name fcswitch with the ip address or put fcswitch in your > hosts file with the IP you want to use. The answer to you problem is right > in the error message. > > > > Skipping host fcswitch as it does not resolve to an IPv4 address > > > > > ------------------------------ > > *From:* [EMAIL PROTECTED] [mailto: > [EMAIL PROTECTED] *On Behalf Of *anjini shukla > *Sent:* Wednesday, August 27, 2008 12:53 PM > *To:* anjini shukla > *Cc:* [email protected] > *Subject:* Re: [mrtg] MRTG Brocade switch monitoring error > > > > I can ping this host, and reply is IP.xx.xx.xx is alive. I can also do an > snmpwalk with this ip address.:( > > > Thanks, > Anjini > > On Wed, Aug 27, 2008 at 5:02 AM, Matthew Petach <[EMAIL PROTECTED]> wrote: > > > The crucial line is > > WARNING: Skipping host fcswitch as it does not resolve to an IPv4 address > > Make sure that the name you put in your config file is the right > name for the device; if you can't ping it by that name, MRTG can't > do anything as far as monitoring it. > > Matt > > > > ----- Original Message ---- > From: anjini shukla <[EMAIL PROTECTED]> > To: [email protected] > Sent: Tuesday, August 26, 2008 4:56:12 PM > Subject: [mrtg] MRTG Brocade switch monitoring error > > Hello, > I am trying to plot graphs for my Brocade 4100 SAN switch and am using > Solaris 10, I am following the documentation given: > http://www.xolution.ch/mrtg/ i have written my config file: > > ~ snip > Target[switch.IP_0]: > 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.12.1&1.3.6.1.4.1.1588.2.1.1.1.6.2.1.11.1:[EMAIL > PROTECTED] > Title[switch.IP_0]: fc throughput on switch fcswitch port 0 (mysun jnic0 > slot7) > PageTop[switch.IP_0]: <H1>fc throughput on switch fcswswitch port 0 (mysun > jnic0 slot7)</H1> > > ~snip > > the error message i am getting is: > > 2008-08-26 12:03:22: WARNING: Skipping host fcswitch as it does not resolve > to an IPv4 address > 2008-08-26 12:03:22: WARNING: no data for > 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.12&1.3.6.1.4.1.1588.2.1.1.1.6.2.1.11:[EMAIL > PROTECTED] > Skipping further queries for Host fcswitch in this round. > 2008-08-26 12:03:22: ERROR: Target[xxx.xxx.xxx.xx_0][_IN_] ' > $target->[0]{$mode} > ' did not eval into defined data > > 2008-08-26 12:03:22: ERROR: Target[xxx.xxx.xxx.xx_0][_OUT_] ' > $target->[0]{$mode} > ' did not eval into defined data > > > > can any one give me any insight on this, ?? > Thanks > > > > >
_______________________________________________ mrtg mailing list [email protected] https://lists.oetiker.ch/cgi-bin/listinfo/mrtg
