Did you reissue the "load" command, and get a good response before running the code?
I have done this frequently with no noticeable problems. Walt ----- Original Message ----- From: "David Brown" <[email protected]> To: <[email protected]> Sent: Friday, December 20, 2002 9:44 AM Subject: Re: [Mspgcc-users] Problems burning flash with pyjtag, gdb > > Actually, I think things are worse than this - using GDB in this way gets > something running on the processor, but I am pretty convinced now that it is > not correctly burning the program. I find that when I use GDB and get the > E00 error, the program works mostly, but I get bugs or crashes that were not > there before. I am now convinced these are caused by incorrect burning of > the program. > > mvh. > > David > > > > > I too have had problems with loading via pyjtag. It's fast when it works, > > but it's abhorrent at other times. I usually run it from a script that > > checks the return code and retries on failure. Often it works after only > > two or three attempts and sometimes it takes more like a dozen attempts > > before it is successful. Then there are the times that is just will not > > work at all. As you suggest, often changing only a few bytes of code will > > make the difference between pyjtag working on the first attempt, or not > > working at all. > > > > Whenever pyjtag is being particularly uncooperative, I resort to the > > GDB/rproxy/FET combination for loading. This is generally really really > > slow, but it pretty much always works. I often get the same error "Remote > > failure reply: E00" when the load completes. However, if I issue the > "load" > > command a second time immediately following the error, it completes > > successfully and in a very short time. > > > > I would greatly appreciate any pointers/fixes from the rest of the > > community, as this business is slowing my development to the point where I > > am almost ready to buy the IAR tools and work under Windows instead of my > > favored OS which is of course Linux. > > > > Walt > > > > ----- Original Message ----- > > From: "David Brown" <[email protected]> > > To: <[email protected]> > > Sent: Thursday, December 19, 2002 4:22 AM > > Subject: [Mspgcc-users] Problems burning flash with pyjtag, gdb > > > > > > > Hi, > > > > > > I use pyjtag to burn my programs into the msp430. Mostly it works fine, > > but > > > sometimes I get a verify error. As far as I can tell, this depends > > entirely > > > on the hex file to burn - if a particular build of the program fails > once, > > > then it will always fail to burn with pyjtag. It will also have > problems > > if > > > I try to burn it with gdb - downloading from gdb gives the error "Remote > > > failure reply: E00". I can download the program with c-spy without > > problem. > > > My workaround at the moment is to make some minor change in the code and > > > hope that the new build will burn properly. > > > > > > I also find burning via gdb to be extremly slow. It is not a big issue > > for > > > me, since I burn via pyjtag before debugging, but it will probably be > > > inconvenient for people who prefer the more graphical interfaces like > > > Insight. > > > > > > mvh. > > > > > > David > > > > > > > > > > > > > > > > > > ------------------------------------------------------- > > > This SF.NET email is sponsored by: Geek Gift Procrastinating? > > > Get the perfect geek gift now! Before the Holidays pass you by. > > > T H I N K G E E K . C O M http://www.thinkgeek.com/sf/ > > > _______________________________________________ > > > Mspgcc-users mailing list > > > [email protected] > > > https://lists.sourceforge.net/lists/listinfo/mspgcc-users > > > > > > > > > > > ------------------------------------------------------- > > This SF.NET email is sponsored by: Geek Gift Procrastinating? > > Get the perfect geek gift now! Before the Holidays pass you by. > > T H I N K G E E K . C O M http://www.thinkgeek.com/sf/ > > _______________________________________________ > > Mspgcc-users mailing list > > [email protected] > > https://lists.sourceforge.net/lists/listinfo/mspgcc-users > > > > > > > > > ------------------------------------------------------- > This SF.NET email is sponsored by: The Best Geek Holiday Gifts! > Time is running out! Thinkgeek.com has the coolest gifts for > your favorite geek. Let your fingers do the typing. Visit Now. > T H I N K G E E K . C O M http://www.thinkgeek.com/sf/ > _______________________________________________ > Mspgcc-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/mspgcc-users >
