from the error it looks like it is looking for /etc/lib/libslb_rf72.so and can not find it. which reader.conf file is it looking at?
can u send the dump of the reader.conf teh LIBPATH if u want to use "/usr/local/pcsc/drivers/slbReflexUSB.bundle/Contents/Linux/reflex_usb" has to be LIBPATH /usr/local/pcsc/drivers/slbReflexUSB.bundle/Contents/Linux/reflex_usb/libslb_rf72.so satish -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Jonathan Sabo (Contractor) Sent: Tuesday, June 29, 2004 11:54 AM To: MUSCLE Subject: RE: [Muscle] help with schlumberger usb setup Yeah, thats exactly what I did and if you read the email I sent to the list it shows exactly that below. Me running the daemon with --debug to stdout and it defaults to reading the /etc/reader.conf which does exactly what you said, it follows the LIBPATH line. Unfortunatly, thats now how the documentation says it should be configured for USB. So how do I configure it for USB? On Tue, 29 Jun 2004, Bommareddy, Satish (Satish) wrote: > Try the following: > > % /usr/local/sbin/pcscd -c /etc/reader.conf --debug stdout > > make sure the LIBPATH in reader.conf points to where u want it to point to > and the channel id is correct > > good luck > > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] Behalf Of Jonathan Sabo > (Contractor) > Sent: Tuesday, June 29, 2004 11:29 AM > To: [EMAIL PROTECTED] > Subject: [Muscle] help with schlumberger usb setup > > > Hello list, > > I am trying to setup m.u.s.c.l.e with a schlumberger 32kv2 card and an > activcard card reader. I have this : > > ccid-0.4.1 pcsc-lite-1.1.1-1-redhat.i386.rpm > ccid-0.4.1.tar.gz slb_rf72 > libusb-0.1.7-5.i686.rpm slb_rf72-drv-1.1.0.tar.gz > libusb-devel-0.1.7-5.i686.rpm slb_rfUSB > muscleframework-1.1.3 slb_rfUSB-drv-0.9.0.tar.gz > muscleframework-1.1.3.tar.gz > > Initially I compiled the pcsc-lite from source but I was having trouble so > I used the rpm shown above. My card reader is a usb cardreader so I > should be using either the ccid or slb_rfUSB bundles but pcsc-lite always > reads /etc/reader.conf and looks for the bundle listed in the file. How > do i make it use the usb bundle? > > [EMAIL PROTECTED] CACCARDS]# /usr/local/sbin/pcscd --debug stdout > pcscdaemon.c:258 main: debug messages to stdout > readerfactory.c:1317 RFInitializeReader: Attempting startup of > Schlumberger Reflex 72 0 0. > dyn_unix.c:32 DYN_LoadLibrary: dlerror() reports /usr/lib/libslb_rf72.so: > cannot open shared object file: No such file or directory > readerfactory.c:219 RFAddReader: Schlumberger Reflex 72 init failed. > pcscdaemon.c:413 main: pcsc-lite daemon ready. > pcscdaemon.c:470 Preparing for suicide > winscard_msg.c:247 SHMProcessEvents: Select returns with failure: > Interrupted system callpcscdaemon.c:174 SVCServiceRun: Error in > SHMProcessEvents > readerfactory.c:1610 RFCleanupReaders: entering cleaning function > pcscdaemon.c:438 at_exit: cleaning /tmp/pcsc > > You can see above it is reading the /etc/reader.conf and expecting a > serial cardreader, unfortunatly thats not what I have. I would like to > use these bundles: > > /usr/local/pcsc/drivers/ifd-ccid.bundle/Contents/Linux/libccid.so.0.4.1 > > or > > /usr/local/pcsc/drivers/slbReflexUSB.bundle/Contents/Linux/reflex_usb > > How do I configure that? > > > Thanks, > > Jonathan > _______________________________________________ > Muscle mailing list > [EMAIL PROTECTED] > http://lists.drizzle.com/mailman/listinfo/muscle > > _______________________________________________ > Muscle mailing list > [EMAIL PROTECTED] > http://lists.drizzle.com/mailman/listinfo/muscle > _______________________________________________ Muscle mailing list [EMAIL PROTECTED] http://lists.drizzle.com/mailman/listinfo/muscle _______________________________________________ Muscle mailing list [EMAIL PROTECTED] http://lists.drizzle.com/mailman/listinfo/muscle
