I still could not get the audio and now it seems it cannot detect the video card at all.
Do you know if it would be easier to setup a PVR-250 given that it is my first time? Ian. On Thu, 20 Jan 2005 21:21:02 -0600, Robert Denier <[EMAIL PROTECTED]> wrote: > It should be noted that I never got the remote working with this card, > but then I didn't try really hard either. I used a sound card for > audio, although according to lspci its standard bt878 audio, so you > should be able to get it using the antennae connection.. I think.. (I > haven't tried yet.) I used a separate ati rf remote. > > I noticed a hauppage WinTV-GO card on pricewatch.com from > surpluscomputers.com for $19 with free shipping. Note that I think this > card is only coaxial (antenae/cable) and composite. Further note the > 57% positive feedback rating on pricewatch.com. This is certainly not a > recommendation to do business with them, since unlike newegg I am not > familiar with them. Its just an FYI. I might order one. > > Does anyone know if the lower cost newer hauppage pvr 150? cards are > ready for use with myth? > > lspci info for the kword card, if it helps someone.. > > 01:06.0 Multimedia video controller: Brooktree Corporation Bt878 Video > Capture (rev 11) > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (4000ns min, 10000ns max) > Interrupt: pin A routed to IRQ 12 > Region 0: Memory at e0000000 (32-bit, prefetchable) [size=4K] > Capabilities: [44] Vital Product Data > Capabilities: [4c] Power Management version 2 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 01:06.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture > (rev 11) > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr- Stepping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (1000ns min, 63750ns max) > Interrupt: pin A routed to IRQ 12 > Region 0: Memory at e0001000 (32-bit, prefetchable) [size=4K] > Capabilities: [44] Vital Product Data > Capabilities: [4c] Power Management version 2 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > Ian Connor wrote: > > >I just purchased this card from newegg and have been following the > >guide on http://www.wilsonet.com/mythtv/ to get it working FC3. > > > >The video and changing cannels now seem to work (back and front end on > >the same shuttle pc that I am using). > > > >However, audio and remote controller not so lucky. I was able to use > >the script at: http://www.mind.lu/%7Eyg/ftvco/ > > > >Is there any such handy scripts to help me get the audio and remote > >working? Has anyone got the magic script? > > > >thanks for any advice - ian > > > > > >On Sat, 08 Jan 2005 04:37:29 -0600, Robert Denier <[EMAIL PROTECTED]> wrote: > > > > > >>I picked up an x-pert tv-pvr by v-stream on newegg > >> > >>TV TUNER KWRLD CAPTR VS-TV878RF (Qty=1,Price=$36.50) > >> > >>It seems to allow mpeg4 encoding and playing back on athlon 2500 systems > >>although I think if you turn the settings way up, you get a little slow > >>down. I probably need to switch away from reiserfs as per the > >>recomendations eventually. (kernel 2.6.10) > >> > >> > > _______________________________________________ > mythtv-users mailing list > mythtv-users@mythtv.org > http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users >
_______________________________________________ mythtv-users mailing list mythtv-users@mythtv.org http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users