fixed modprobe.conf.. same problem.. it's weird that it detected it with the typo in the first place..
On 23 Jul 2005 13:31:33 -0700, Jim Reith <[EMAIL PROTECTED]> wrote: > >downloaded the correct firmware and fixed the module options, still > >the same problem.. anymore idea? Thanks again. > > > >alias char-major-81 videodev > >alias char-major-81-0 ivtv > >alias char-major-81-1 ivtv > >options cx25480 i2c_enable=1,1 > >options saa7127 i2c_enable=-1,-1 > > HA! I see it... You have a typo in your options (if the above is > correct) cx25480 != cx25840 > > subtle... > > > > >ivtv: ==================== START INIT IVTV ==================== > >ivtv: version 0.3.7 (a) loading > >ivtv: Linux version: 2.6.11-1.35_FC3 686 REGPARM 4KSTACKS gcc-3.4 > >ivtv: In case of problems please include the debug info > >ivtv: between the START INIT IVTV and END INIT IVTV lines when > >ivtv: mailing the ivtv-devel mailinglist. > >ivtv: Autodetected WinTV PVR 150 card > >ivtv: Found an iTVC16 based chip > >ACPI: PCI interrupt 0000:03:08.0[A] -> GSI 11 (level, low) -> IRQ 11 > >ivtv: XXX PCI device: 0x1a30 vendor: 0x8086 > >tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8005926 > >tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) > >tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) > >tveeprom: audio_processor = MSP3410D (type = 5) > >ivtv: i2c attach [client=tveeprom[50],ok] > >tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 > >ivtv: i2c attach [client=(tuner unset),ok] > >cx25840: starting probe on adapter ivtv i2c driver #0 (0x10005) > >cx25840: detecting cx25840 client on address 0x88 > >cx25840: cx25843-23 found. Initializing... > >cx25840: requesting /lib/modules/HcwMakoA.ROM > >cx25840: firmware loaded > >ivtv: i2c attach [client=cx25840[50],ok] > >ivtv: i2c attach [client=wm8775[50],ok] > >ivtv: Tuner Type 57, Tuner formats 0x00001000, Radio: yes, Model > >0x00914652, Revision 0x00000001 > >ivtv: NTSC tuner detected > >ivtv: Radio detected > >ivtv: Encoder revision: 0x02040011 > >ivtv: Configuring WinTV PVR 150 card with 5 streams > >ivtv: Registered v4l2 device for encoder MPEG minor 0 > >ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) > >ivtv: Registered v4l2 device for encoder YUV minor 32 > >ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) > >ivtv: Registered v4l2 device for encoder VBI minor 224 > >ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total) > >ivtv: Registered v4l2 device for encoder PCM audio minor 24 > >ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) > >ivtv: Registered v4l2 device for encoder radio minor 64 > >ivtv: Create encoder radio stream > >ivtv: Setting Tuner 57 > >tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #0 > >cx25840: decoder set norm NTSC > >cx25840: decoder set input (6) > >cx25840: now setting Tuner input > >cx25840: set audio input (0) > >ivtv: Switching standard to NTSC. > >cx25840: decoder set norm NTSC > >ivtv: Initialized WinTV PVR 150, card #0 > >ivtv: Autodetected WinTV PVR 150 card > >ivtv: Found an iTVC16 based chip > >ACPI: PCI interrupt 0000:03:09.0[A] -> GSI 10 (level, low) -> IRQ 10 > >ivtv: XXX PCI device: 0x1a30 vendor: 0x8086 > >tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8005926 > >tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) > >tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x00001000) > >tveeprom: audio_processor = MSP3410D (type = 5) > >ivtv: i2c attach [client=tveeprom[50],ok] > >tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1 > >ivtv: i2c attach [client=(tuner unset),ok] > >cx25840: starting probe on adapter ivtv i2c driver #1 (0x10005) > >ivtv: i2c attach [client=wm8775[50],ok] > >ivtv: Tuner Type 57, Tuner formats 0x00001000, Radio: yes, Model > >0x00914652, Revision 0x00000001 > >ivtv: Radio detected > >ivtv: ivtv_enc_thread: pid = 11202, itv = 0xe2230d20 > >ivtv: ivtv_enc_vbi_thread: pid = 11203, itv = 0xe2230d20 > >ivtv: Encoder revision: 0x02040011 > >ivtv: Configuring WinTV PVR 150 card with 5 streams > >ivtv: Registered v4l2 device for encoder MPEG minor 1 > >ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) > >ivtv: Registered v4l2 device for encoder YUV minor 33 > >ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) > >ivtv: Registered v4l2 device for encoder VBI minor 225 > >ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total) > >ivtv: Registered v4l2 device for encoder PCM audio minor 25 > >ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) > >ivtv: Registered v4l2 device for encoder radio minor 65 > >ivtv: Create encoder radio stream > >ivtv: Setting Tuner 57 > >tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #1 > >ivtv: i2c client addr: 0x44 not found for command 0x40046403! > >ivtv: i2c client addr: 0x44 not found for command 0x40046404! > >ivtv: i2c client addr: 0x44 not found for command 0x4004646e! > >ivtv: Switching standard to NTSC. > >ivtv: i2c client addr: 0x44 not found for command 0x40046403! > >ivtv: Initialized WinTV PVR 150, card #1 > >ivtv: ==================== END INIT IVTV ==================== > >ivtv: ivtv_enc_thread: pid = 11315, itv = 0xe22542f4 > >ivtv: ivtv_enc_vbi_thread: pid = 11316, itv = 0xe22542f4 > > > >> ivtv: Encoder revision: 0x02050032 > >> ivtv: Encoder Firmware may be buggy, use version 0x02040011 > >> > >> Go here and get the correct firmware > >> http://ivtv.writeme.ch/tiki-index.php?page=FirmwareVersions > >> > >> Then try again. I don't have a PVR 500 so not sure it will work, but it > >> can't hurt to try. > >> > >> > >_______________________________________________ > >mythtv-users mailing list > >mythtv-users@mythtv.org > >http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users > > > -- who, what, where, when? _______________________________________________ mythtv-users mailing list mythtv-users@mythtv.org http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users