----- Original Message ----- From: "Tom E. Craddock Jr." <[EMAIL PROTECTED]> To: "Discussion about mythtv" <mythtv-users@mythtv.org> Sent: Wednesday, September 21, 2005 5:56 PM Subject: Re: [mythtv-users] 6200ch 1394 Drivers & such
> brett olah wrote: > > >----- Original Message ----- > >From: "Ian Forde" <[EMAIL PROTECTED]> > >To: "Discussion about mythtv" <mythtv-users@mythtv.org> > >Sent: Tuesday, September 20, 2005 10:12 PM > >Subject: Re: [mythtv-users] 6200ch 1394 Drivers & such > > > > > > > > > >>On Tue, 2005-09-20 at 21:26 -0700, brett olah wrote: > >> > >> > >>>I compiled 0.18.1 ... no problems > >>> > >>>but ... > >>> > >>>Where/How do I turn it on? I think I've exhausted > >>> > >>> > >mythtv-setup/mythfrontend > > > > > >>>setup, did I miss it? > >>> > >>> Brett;] > >>> > >>>depmod: > >>>ieee1394: Initialized config rom entry `ip1394' > >>>ohci1394: $Rev: 1223 $ Ben Collins <[EMAIL PROTECTED]> > >>>ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[209] > >>> > >>> > >MMIO=[f8025000-f80257ff] > > > > > >>>Max Packet=[2048] > >>>ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d80000181b03] > >>>ieee1394: Node added: ID:BUS[0-01:1023] GUID[0014e8fffe19dd19] > >>>ieee1394: raw1394: /dev/raw1394 device initialized > >>> > >>># 1394 Drivers :) > >>>raw1394 33325 0 > >>>dv1394 24461 0 > >>>ohci1394 37849 1 dv1394 > >>>ieee1394 308216 3 raw1394,dv1394,ohci1394 > >>> > >>> > >>>configure output: > >>>FireWire support yes > >>>compiled w/ no Errors only unrelated warnings: > >>>vbitext/cc.cpp:119: warning: 'int webtv_check(char*, int)' defined but > >>> > >>> > >not > > > > > >>>used > >>>mpeg/mpegstreamdata.h:139: warning: unused parameter 'tspacket' > >>> > >>> > >>Well, my master backend (the one with the firewire port) has > >>libiec61883, libavc1394, librom1394, libraw1394, and libdc1394. It goes > >>without saying that I have the -devel versions installed too. I > >>compared your lsmod output to mine and they're the same. So that looks > >>fine on your end. In mythtv-setup, when you setup a firewire input, you > >>should see the option for internal firewire channel changing in the same > >>place that you normally see it for capture cards - in "Input > >>Connections", leave the "External Channel Changing Program" field > >>blank... > >> > >>-I > >> > >> > >> > >> > > > > > >Hmmm yup yup yup , > >I may be dense ... lemme walk through this ... > ># mythtv-setup > > > Select 4. Input Connectors > > > Select SVideo-0 < main (Which is my digital Line Up) > >(This is the Dialog where the External Channel Change App Input Box is > >[Note: it's blank]) > >There is however no mention (on this screen) of the word Firewire or 1934 or > >6200 > > > >Initially (using the 6200ch in contrib) I received the following: > > node 1: vendor_id = 0x000011d8 model_id = 0x00000000 > > Could not find Motorola DCT-6200 on the 1394 bus. > > > >I read some docs ... attempted to hack it and add my id's > >a tweak on the output and: > > node 1: vendor_id = 0x000011d8 model_id = 0x00000000 > > Warning: Your Unit Spec ID (0x0000005e) is unexpected. > > Warning: Your Unit Software Version (0x00000001) is unexpected. > > AV/C Command: 007 = Op1=0x00487C20 Op2=0x00487C20 Op3=0x00487C27 > >then the channel change fails. > > > >My box is brand new (just picked it up last week) and clearly the CTL_CMD0 > >(Op1,2&3) > >is not a signal that my box is happy with. > > > >Any way to find out if this 6200's ID's are listed/supported by the current > >implementation? > > > > Brett > > > > > > Is MythTV getting the TV signal from a firewire input or from S-vid? If > its s-vid, I dont think you can use the firewire connection to change > the channels for that input. As I understand it (which very possibly > could be wrong) you can only change the channel thru firewire if the TV > Signal comming to your MythTV box is thru firewire. Reading the > response from Ian, he says "In mythtv-setup, when you setup a *firewire > input*, you should see the option for internal firewire channel changing > in the same place that you normally see it for capture cards - in "Input > Connections", leave the "External Channel Changing Program" field > blank..." he says to set up a FireWire INPUT, not s-vid. > > Tom > Are you sure? .../mythtv-0.18.1/contrib/6200ch-README "6200ch is a small program that Stacey Son ([EMAIL PROTECTED]) wrote to change channels on a Motorola DCT-6200 cable box via a 1394 (aka. Firewire) connection." # 6200ch <your_favorite_channel_number> I was under the impression that this functionality was added in 0.18.1 as an internal app instead of an external config/shell call. He implies that it is not for capture ... just channel. Brett > _______________________________________________ > mythtv-users mailing list > mythtv-users@mythtv.org > http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users > _______________________________________________ mythtv-users mailing list mythtv-users@mythtv.org http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users