Hi,
On Wed, Mar 23, 2016 at 05:16:01PM +0300, Denis V. Lunev wrote:
> From: Pavel Borzenkov <[email protected]>
>
> There exist some cases when a client knows that the data it is going to
> write is all zeroes. Such cases include mirroring or backing up a device
> implemented by a sparse file.
>
> With current NBD command set, the client has to issue NBD_CMD_WRITE
> command with zeroed payload and transfer these zero bytes through the
> wire. The server has to write the data onto disk, effectively denying
> the sparseness.
>
> To remedy this, the patch adds WRITE_ZEROES extension with one new
> NBD_CMD_WRITE_ZEROES command.
>
> Signed-off-by: Pavel Borzenkov <[email protected]>
> Reviewed-by: Roman Kagan <[email protected]>
> Signed-off-by: Denis V. Lunev <[email protected]>
> CC: Wouter Verhelst <[email protected]>
> CC: Paolo Bonzini <[email protected]>
> CC: Kevin Wolf <[email protected]>
> CC: Stefan Hajnoczi <[email protected]>
> ---
> doc/proto.md | 44 ++++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 44 insertions(+)
>
> diff --git a/doc/proto.md b/doc/proto.md
> index 463ef8a..cda213c 100644
> --- a/doc/proto.md
> +++ b/doc/proto.md
> @@ -241,6 +241,8 @@ immediately after the global flags field in oldstyle
> negotiation:
> schedule I/O accesses as for a rotational medium
> - bit 5, `NBD_FLAG_SEND_TRIM`; should be set to 1 if the server supports
> `NBD_CMD_TRIM` commands
> +- bit 6, `NBD_FLAG_SEND_WRITE_ZEROES`; should be set to 1 if the server
> + supports `NBD_CMD_WRITE_ZEROES` commands
>
> ##### Client flags
>
> @@ -471,6 +473,10 @@ The following request types exist:
> about the contents of the export affected by this command, until
> overwriting it again with `NBD_CMD_WRITE`.
>
> +* `NBD_CMD_WRITE_ZEROES` (6)
> +
> + Defined by the experimental `WRITE_ZEROES` extension; see below.
> +
> * Other requests
>
> Some third-party implementations may require additional protocol
> @@ -594,6 +600,44 @@ option reply type.
> message if they do not also send it as a reply to the
> `NBD_OPT_SELECT` message.
>
> +### `WRITE_ZEROES` extension
> +
> +There exist some cases when a client knows that the data it is going to write
> +is all zeroes. Such cases include mirroring or backing up a device
> implemented
> +by a sparse file. With current NBD command set, the client has to issue
> +`NBD_CMD_WRITE` command with zeroed payload and transfer these zero bytes
> +through the wire. The server has to write the data onto disk, effectively
> +denying the sparseness.
> +
> +To remedy this, a `WRITE_ZEROES` extension is envisioned. This extension adds
> +one new command with two command flags.
> +
> +* `NBD_CMD_WRITE_ZEROES` (6)
> +
> + A write request with no payload. Length and offset define the location
> + and amount of data to be zeroed.
> +
> + The server MUST zero out the data on disk, and then send the reply
> + message. The server MAY send the reply message before the data has
> + reached permanent storage.
> +
> + If the `NBD_FLAG_SEND_FUA` flag ("Force Unit Access") was set in the
> + export flags field, the client MAY set the flag `NBD_CMD_FLAG_FUA` (bit
> 0)
> + in the command flags field. If this flag was set, the server MUST NOT
> send
> + the reply until it has ensured that the newly-zeroed data has reached
> + permanent storage.
> +
> + If the flag `NBD_CMD_FLAG_MAY_TRIM` (bit 1) was set by the client in the
> + command flags field, the server MAY use trimming to zero out the area,
> + but it MUST ensure that the data reads back as zero.
> +
> + If an error occurs, the server SHOULD set the appropriate error code
> + in the error field. The server MAY then close the connection.
> +
> +The server SHOULD return `ENOSPC` if it receives a write zeroes request
> +including one or more sectors beyond the size of the device. It SHOULD
> +return `EPERM` if it receives a write zeroes request on a read-only export.
> +
So, the semantics of your proposed WRITE_ZEROES are exactly the same as
the WRITE command, except that no payload is sent?
In that case, I think it's slightly more sensible if we don't add a new
command, but instead just have an NBD_CMD_FLAG_ZEROES added to the WRITE
command instead. After all, they're going to be (mostly) the same
anyway.
Did you propose a separate command for a specific reason that I'm
missing (or forgetting), or is that just an oversight?
--
< ron> I mean, the main *practical* problem with C++, is there's like a dozen
people in the world who think they really understand all of its rules,
and pretty much all of them are just lying to themselves too.
-- #debian-devel, OFTC, 2016-02-12
------------------------------------------------------------------------------
Transform Data into Opportunity.
Accelerate data analysis in your applications with
Intel Data Analytics Acceleration Library.
Click to learn more.
http://pubads.g.doubleclick.net/gampad/clk?id=278785351&iu=/4140
_______________________________________________
Nbd-general mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/nbd-general
