Hello everyone, I am a beginner to the SNMP protocal. These days I'm trying to
configure the snmpd.conf, but it failed. Because I checked the website, it said
that I need find the "com2sec notConfigUser...", but actually my snmpd.conf
doesnt have this content, so I dont know how to configure my snmpd.conf. I will
paste the content of my snmpd.conf to you.Thank you so much for your time and
instruction.
###############################################################################
#
# EXAMPLE.conf:
# An example configuration file for configuring the Net-SNMP agent ('snmpd')
# See the 'snmpd.conf(5)' man page for details
#
# Some entries are deliberately commented out, and will need to be explicitly
activated
#
###############################################################################
#
# AGENT BEHAVIOUR
#
# Listen for connections from the local system only
agentAddress udp:127.0.0.1:161
# Listen for connections on all interfaces (both IPv4 *and* IPv6)
#agentAddress udp:161,udp6:[::1]:161
###############################################################################
#
# SNMPv3 AUTHENTICATION
#
# Note that these particular settings don't actually belong here.
# They should be copied to the file /var/lib/snmp/snmpd.conf
# and the passwords changed, before being uncommented in that file *only*.
# Then restart the agent
# createUser authOnlyUser MD5 "remember to change this password"
# createUser authPrivUser SHA "remember to change this one too" DES
# createUser internalUser MD5 "this is only ever used internally, but still
change the password"
# If you also change the usernames (which might be sensible),
# then remember to update the other occurances in this example config file to
match.
###############################################################################
#
# ACCESS CONTROL
#
# system + hrSystem groups
only
view systemonly included .1.3.6.1.2.1.1
view systemonly included .1.3.6.1.2.1.25.1
# Full access from the local
host
#rocommunity public localhost
# Default access to basic
system info
rocommunity public default -V systemonly
# Full access from an example
network
# Adjust this network
address to match your local
# settings, change the
community string,
# and check the
'agentAddress' setting above
#rocommunity secret 10.0.0.0/16
# Full read-only access for
SNMPv3
rouser authOnlyUser
# Full write access for
encrypted requests
# Remember to activate the
'createUser' lines above
#rwuser authPrivUser priv
# It's no longer typically necessary to use the full 'com2sec/group/access'
configuration
# r[ow]user and r[ow]community, together with suitable views, should cover
most requirements
###############################################################################
#
# SYSTEM INFORMATION
#
# Note that setting these values here, results in the corresponding MIB
objects being 'read-only'
# See snmpd.conf(5) for more details
sysLocation Sitting on the Dock of the Bay
sysContact Me <m...@example.org>
# Application + End-to-End
layers
sysServices 72
#
# Process Monitoring
#
# At least one 'mountd' process
proc mountd
# No more than 4 'ntalkd' processes - 0 is OK
proc ntalkd 4
# At least one 'sendmail' process, but no more
than 10
proc sendmail 10 1
# Walk the UCD-SNMP-MIB::prTable to see the resulting output
# Note that this table will be empty if there are no "proc" entries in the
snmpd.conf file
#
# Disk Monitoring
#
# 10MBs required on root disk, 5% free on /var,
10% free on all other disks
disk / 10000
disk /var 5%
includeAllDisks 10%
# Walk the UCD-SNMP-MIB::dskTable to see the resulting output
# Note that this table will be empty if there are no "disk" entries in the
snmpd.conf file
#
# System Load
#
# Unacceptable 1-, 5-, and 15-minute load
averages
load 12 10 5
# Walk the UCD-SNMP-MIB::laTable to see the resulting output
# Note that this table *will* be populated, even without a "load" entry in the
snmpd.conf file
###############################################################################
#
# ACTIVE MONITORING
#
# send SNMPv1 traps
trapsink localhost public
# send SNMPv2c traps
#trap2sink localhost public
# send SNMPv2c INFORMs
#informsink localhost public
# Note that you typically only want *one* of these three lines
# Uncommenting two (or all three) will result in multiple copies of each
notification.
#
# Event MIB - automatically generate alerts
#
# Remember to activate the 'createUser'
lines above
iquerySecName internalUser
rouser internalUser
# generate traps on UCD error conditions
defaultMonitors yes
# generate traps on linkUp/Down
linkUpDownNotifications yes
###############################################################################
#
# EXTENDING THE AGENT
#
#
# Arbitrary extension commands
#
extend test1 /bin/echo Hello, world!
extend-sh test2 echo Hello, world! ; echo Hi there ; exit 35
#extend-sh test3 /bin/sh /tmp/shtest
# Note that this last entry requires the script '/tmp/shtest' to be created
first,
# containing the same three shell commands, before the line is uncommented
# Walk the NET-SNMP-EXTEND-MIB tables (nsExtendConfigTable,
nsExtendOutput1Table
# and nsExtendOutput2Table) to see the resulting output
# Note that the "extend" directive supercedes the previous "exec" and "sh"
directives
# However, walking the UCD-SNMP-MIB::extTable should still returns the same
output,
# as well as the fuller results in the above tables.
#
# "Pass-through" MIB extension command
#
#pass .1.3.6.1.4.1.8072.2.255 /bin/sh PREFIX/local/passtest
#pass .1.3.6.1.4.1.8072.2.255 /usr/bin/perl PREFIX/local/passtest.pl
# Note that this requires one of the two 'passtest' scripts to be installed
first,
# before the appropriate line is uncommented.
# These scripts can be found in the 'local' directory of the source
distribution,
# and are not installed automatically.
# Walk the NET-SNMP-PASS-MIB::netSnmpPassExamples subtree to see the resulting
output
#
# AgentX Sub-agents
#
# Run as an AgentX master agent
master agentx
# Listen for network connections
(from localhost)
# rather than the default named
socket /var/agentx/master
#agentXSocket tcp:localhost:705
That is my snmpd.conf, do you know how to configure this? really thank you for
your time.
------------------------------------------------------------------------------
Download BIRT iHub F-Type - The Free Enterprise-Grade BIRT Server
from Actuate! Instantly Supercharge Your Business Reports and Dashboards
with Interactivity, Sharing, Native Excel Exports, App Integration & more
Get technology previously reserved for billion-dollar corporations, FREE
http://pubads.g.doubleclick.net/gampad/clk?id=164703151&iu=/4140/ostg.clktrk
_______________________________________________
Net-snmp-users mailing list
Net-snmp-users@lists.sourceforge.net
Please see the following page to unsubscribe or change other options:
https://lists.sourceforge.net/lists/listinfo/net-snmp-users
