From: Stephen Warren <swar...@nvidia.com> The Synopsys DWC EQoS is a configurable IP block which supports multiple options for bus type, clocking and reset structure, and feature list. Extend the DT binding to define a "compatible value" for the configuration contained in NVIDIA's Tegra186 SoC, and define some new properties and list property entries required by that configuration.
Signed-off-by: Stephen Warren <swar...@nvidia.com> --- .../bindings/net/snps,dwc-qos-ethernet.txt | 60 ++++++++++++++++++++-- 1 file changed, 56 insertions(+), 4 deletions(-) diff --git a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt index 51f8d2eba8d8..6cd4129364a9 100644 --- a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt +++ b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt @@ -1,21 +1,72 @@ * Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC) +This binding supports the Synopsys Designware Ethernet QoS (Quality Of Service) +IP block. The IP supports multiple options for bus type, clocking and reset +structure, and feature list. Consequently, a number of properties and list +entries in properties are marked as optional, or only required in specific HW +configurations. Required properties: -- compatible: Should be "snps,dwc-qos-ethernet-4.10" +- compatible: One of: + - "snps,dwc-qos-ethernet-4.10" + - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10" - reg: Address and length of the register set for the device -- clocks: Phandles to the reference clock and the bus clock -- clock-names: Should be "phy_ref_clk" for the reference clock and "apb_pclk" - for the bus clock. +- clocks: Phandle and clock specifiers for each entry in clock-names, in the + same order. See ../clock/clock-bindings.txt. +- clock-names: May contain any/all of the following depending on the IP + configuration, in any order: + - "phy_ref_clk". The reference clock provided directly to the PHY. + Only required if under SW control, i.e. not provided by some fixed source + such as a crystal. + - "apb_pclk" (alternate name "slave_bus"; only one alternate must appear). + The CPU/slave-bus (CSR) interface clock. Despite the name, this applies to + any bus type; APB, AHB, AXI, etc. The HW signal name is hclk_i (AHB) or + clk_csr_i (other buses). + - "master_bus". The master bus interface clock. Only required in + configurations that use a separate clock for the master and slave bus + interfaces. The HW signal name is hclk_i (AHB) or aclk_i (AXI). + - "rx". The receive path clock. The HW signal name is clk_rx_i. + - "tx". The transmit path clock. The HW signal name is clk_tx_i. + - "ptp_ref". The PTP reference clock. The HW signal name is clk_ptp_ref_i. + + Note: Support for additional HW configurations may require adding the + following clocks to this list in the future: clk_rx_125_i, clk_tx_125_i, + clk_pmarx_0_i, clk_pmarx1_i, clk_rmii_i. + + The following compatible values require the following set of clocks: + - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10": + - "slave_bus" + - "master_bus" + - "rx" + - "tx" + - "ptp_ref" + - "snps,dwc-qos-ethernet-4.10": + - "phy_ref_clk" + - "apb_clk" - interrupt-parent: Should be the phandle for the interrupt controller that services interrupts for this device - interrupts: Should contain the core's combined interrupt signal - phy-mode: See ethernet.txt file in the same directory +- resets: Phandle and reset specifiers for each entry in reset-names, in the + same order. See ../reset/reset.txt. +- reset-names: May contain any/all of the following depending on the IP + configuration, in any order: + - "eqos". The reset to the entire module. The HW signal name is hreset_n + (AHB) or aresetn_i (AXI). + + The following compatible values require the following set of clocks: + (the reset properties may be omitted if empty) + - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10": + - "eqos". + - "snps,dwc-qos-ethernet-4.10": + - None. Optional properties: - dma-coherent: Present if dma operations are coherent - mac-address: See ethernet.txt in the same directory - local-mac-address: See ethernet.txt in the same directory +- phy-reset-gpios: Phandle and specifier for any GPIO used to reset the PHY. + See ../gpio/gpio.txt. - snps,en-lpi: If present it enables use of the AXI low-power interface - snps,write-requests: Number of write requests that the AXI port can issue. It depends on the SoC configuration. @@ -52,6 +103,7 @@ ethernet2@40010000 { reg = <0x40010000 0x4000>; phy-handle = <&phy2>; phy-mode = "gmii"; + phy-reset-gpios = <&gpioctlr 43 GPIO_ACTIVE_LOW>; snps,en-tx-lpi-clockgating; snps,en-lpi; -- 2.9.3